CNB D2960N/D2960P Owner's manual

Brand: CNB

Model: D2960N/D2960P

Category: Security cameras

Type: Owner's manual

This manual is also suitable for

D2960NVD/D2960PVD

Axis

SDNR Camera Series

P/N : 3810-0091A

(Ver.0609E)

Color Dome Camera Series

Design and specifications are subject to

change without notice.

6 7

8 9

10 11

12 13

14 15

16 17

1918

2120

2322

24 25

26 27

28 29

3130

3332

3534

36 37

38 39

40 41

4342

4544

4746

OWNER'S MANUAL

DIGITAL COLOR DOME CAMERA

Digital Slow Shutter

High Resolution

DSS

On-Screen Display

OSD

Super Digital Noise Reduction

SDNR

Easy Install

COLOR DOME CAMERA

INFORMATION

This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15

of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at their own expense.

WARNING

The manufacturer could void the user's authority to operate the equipment.

CAUTION - To prevent electric shock and risk of fire hazards:

Do NOT use power sources except for that specified.

Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should abide to all local codes.

CAUTION!

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Explanation of two Symbols

The lightning flash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of un-insulated

"dangerous voltage" within the product's enclosure that may be of

sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to

alert the user to the presence of important operating and maintenance-

(servicing) instructions in the literature accompanying the appliance.

THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.

"WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE"

. User Information

1. SAFETY INSTRUCTIONS

2. PRECAUTIONS

3. FEATURES

4. COMPOSITION

5. INSTALLATION

6. NAME AND FUNCTIONS

7. CONNECTIONS

8. OPERATING CAMERA

9. SPECIFICATIONS

10. TROUBLESHOOTING

Before using this camera, please read this operation manual carefully to obtain

the best result and keep this manual for future reference.

Thank you for purchasing this COLOR VIDEO CAMERA.

If you have trouble operating your camera, refer to the following table.

If the guidelines do not enable you to solve the problem, contact an authorized technician.

. AC 24V / DC 12V Input Model

. DC 12V Input Model

. Vandal Proof Dome Camera

Flush Vandal Proof Dome Camera

. General Dome Camera

. Contents

Do not install the camera in extreme temperature

conditions.

Do use the camera under conditions where temperatures

are within -10C to 50C. Especially be careful for

ventilation under high temperature.

Do not install or use the camera in an environment

where the humidity is high.

It can cause the image quality to be poor.

Do not install the camera under unstable lighting

conditions.

Severe lighting change or flicker can cause the camera

to work improperly.

Never use the camera close to a gas or oil leak.

It can cause malfunctions to occur.

Do not disassemble the camera.

There are no user-serviceable parts inside it.

Do not drop the camera or subject them to physical

shocks.

It can cause malfunctions to occur.

Never keep the camera face to strong light directly.

It can damage CCD.

Do not expose the camera to rain or spill beverage on it.

If it gets wet, wipe it dry immediately. Liquids can

contain minerals that corrode the electronic components.

Note

When this camera is installed near wireless communication

devices that emits strong electromagnetic field, irregularity

such as noise on the monitor may appear.

2. PRECAUTIONS

6. NAME AND FUNCTIONS

7. CONNECTION

4. COMPOSITION

5. INSTALLATION

Read Instructions

Read all of the safety and operating instructions

before using the product.

Installation

Do not place this product on an unstable cart, stand,

or table. The product may fall causing serious injury

to a child or adult, and damage to the product.

Use only with a cart or stand recommended by the

manufacturer, or sold with the product.

Mounting should follow the manufacturer's instructions,

and should use a mounting accessory recommended

by manufacturer.

Power source

This product should be operated only from the type

of power source indicated on the marking label.

If you are not sure of the type of power supplied to

your home, consult your dealer or local power

company.

Retain Instructions

Save this instructions for later use.

Cleaning

Unplug this appliance from wall outlet before

cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

Water and Moisture.

Do not use this product near water or moisture.

(For example. near a bathtub, wash bowl, kitchen

sink, or laundry tub, in a wet basement, or near a

swimming pool,etc)

1. SAFETY INSTRUCTIONS

High sensitivity 1/3 Inch Sony Super HAD CCD Pick-Up

Min lllumination : 0.1 Lux (F1.2)

0.0008 Lux (DSS x 128)

Electronic day & night mode selectable.

High performance menus for functions

DNR (Digital Noise Reduction)

It has an assistant reducing image noise efficiently and It shows clear and

sharp image display even in the dark

• Privacy zone selectable.

• Motion detection selectable.

• Super BLC selectable.

• Sharpness enhanced adjustable.

• Flickerless On/Off

3. FEATURES

8. OPERATING CAMERA

LENS

SHUTTER

WHITE BALANCE

BACKLIGHT

AGC (Auto Gain Control)

DNR (Digital Noise Reduction)

SENS-UP

SPECIAL

EXIT

• MANUAL • DC/VIDEO

• ESC • MANUAL • FLK

• ATW • MANUAL • AWC

• OFF • LOW • MIDDLE • HIGH

• OFF • AUTO

• CAMERA ID • COLOR • SYNC

• MOTION DET • PRIVACY • MIRROR

• SHARPNESS • RESET • RETURN

SETUP MENU

NTSC PAL

2:1 Interlace Transfer 1/3 Inch Super HAD CCD

768 (H) x 494 (V) 752 (H) x 582 (V)

Composite: 1.0Vp-p, 75, Unbalanced

Internal Sync

More than 50dB (AGC OFF)

530 TV Lines

0.1 Lux (30IRE, AGC ON), 0.0008Lux (DSS x128)

Fixed Lens (f=2.45mm, 3.8mm, 6mm Selectable)/ Vari-focal Lens

Auto / Manual / Flickerless

x128~1/60~1/120,000 Sec.[NTSC], x128~1/50~1/120,000 Sec.[PAL]

ATW (1,800K~10,500K) / AWC / MANUAL

OFF / LOW / MIDDLE / HIGH

Signal System

Image Sensor

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Horizontal Resolution

Sensitivity (F1.2)

Lens

Electronic Shutter

White Balance

Back Light Compensation

High ResolutionMODEL

9. SPECIFICATIONS

OFF / LOW / MIDDLE / HIGH

ON / OFF

ON / OFF (4 Programmable Zone)

ON / OFF (Horizontal)

ON / OFF (Level Adjustable)

DC Iris / Video Iris / Manual Lens

DC 12V(10V~15V)

180mA / 2.2W (Max)

-10~+50(Recommendation:-5~+40)

-20~+60

100 mm

Approx. 366g(General) / 844g(Vandal Proof) / 1210g(Flush Vandal Proof)

Auto Gain Control

DNR

Color (D&N)

Motion Detection

Privacy

Mirror

Sharpness

Applicable Lens

Supply Voltage

Power Consumption

Operating Temperature

Storage Temperature

Dome Size (Ø)

Weight

DC 12V Input Model

NTSC PAL

2:1 Interlace Transfer 1/3 Inch Super HAD CCD

768 (H) x 494 (V) 752 (H) x 582 (V)

Composite: 1.0V p-p, 75, Unbalanced

Internal Sync / External Line-Lock Sync

More than 50dB (AGC OFF)

530 TV Lines

0.1 Lux (30IRE, AGC ON), 0.0008Lux (DSS x128)

Fixed Lens (f=2.45mm, 3.8mm, 6mm Selectable)/ Vari-focal Lens

Auto / Manual / Flickerless

x128~1/60~1/120,000 Sec.[NTSC], x128~1/50~1/120,000 Sec.[PAL]

ATW (1,800K~10,500K) / AWC / MANUAL

OFF / LOW / MIDDLE / HIGH

Signal System

Image Sensor

Effective Pixels

Video Output

Sync. System

Luminance S/N Ratio

Horizontal Resolution

Sensitivity (F1.2)

Lens

Electronic Shutter

White Balance

Back Light Compensation

High ResolutionMODEL

9. SPECIFICATIONS

OFF / LOW / MIDDLE / HIGH

ON / OFF

ON / OFF (4 Programmable Zone)

ON / OFF (Horizontal)

ON / OFF (Level Adjustable)

DC Iris / Video Iris / Manual Lens

AC 24V (20V~28V) or DC 12V (10V~15V)

330mA / 4W (Max)

-10~+50(Recommendation:-5~+40)

-20~+60

100 mm

Approx. 366g(General) / 844g(Vandal Proof) / 1210g(Flush Vandal Proof)

Auto Gain Control

DNR

Color (D&N)

Motion Detection

Privacy

Mirror

Sharpness

Applicable Lens

Supply Voltage

Power Consumption

Operating Temperature

Storage Temperature

Dome Size (Ø)

Weight

AC 24V / DC 12V Input Model

10. TROUBLESHOOTING

SETUP

- Press the MENU button to acces the

setup mode.

• Select the status using the , ,

, button.

• Move the cuser to character enter

location by using the button.

Use five setup Menu buttons

on Inside of the camera.

Setting up the Menu

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

MANUAL

ESC

ATW

OFF

LOW

OFF

1. Press the MENU button to access the SETUP mode.

• SETUP menu is displayed on the monitor screen.

2. Select the desired feature using the UP or DOWN button.

• Each time you press the UP or DOWN button, the arrow indicator moves UP or DOWN.

• Move the arrow indicator the desired feature item.

3. Change the status of the selected feature using the LEFT or RIGHT button.

• If you Press RIGHT or LEFT button, it appears available status. Press the button when gets desired feature.

4. When completed, move the arrow indicator to 'EXIT' and press the MENU button.

Main Menu -

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

---

AWC

HIGH

LOW

AUTO

You can access submenu using MENU button.

For the mode with '---', you may not access submenu.

NOTE

Main Menu -

LENS

1) Setting up the LENS

Select the lens pressing the RIGHT button.

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

MANUAL

FLK

AWC

HIGH

OFF

---

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

---

AWC

HIGH

LOW

AUTO

On the SETUP menu screen, move the ar row indicator to the lens using the UP or DOWN button.

Select the desired feature using the LEF T or RIGHT button.

Main Menu -

WHITE BALANCE

3) WHITE BAL. (White Balance)

When needs color control on the screen, use 'WHITE BALANCE' function.

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

---

AWC

HIGH

OFF

---

P ress the MENU button to display the SETUP menu and move the arrow indicator to 'WHITE BALANCE'

using the UP or DOWN button.

Set 'WHITE BAL.' T o the desired mode using LEFT or RIGHT button.

ATW(Auto Tracking White Balance): When color temperature is 1,800 K~10,500 K, select this mode.

(ex. A fluorecent lamp, outdoor)

AWC(Auto White Balance Control): The white balance is automatically adjusted in a specific environment.

In order to obtain the best result, press the set button while the camera focuses on white paper.

If the environment including the light source is changed, you have to adjust the white balance again.

2) Shutter status and speed control

You can control brightness of the screen by the shutter speed.

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

---

AWC

HIGH

OFF

---

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

MANUAL

FLK

AWC

HIGH

OFF

---

Press the MENU button to display the setup menu and move the arrow indicator to 'SHUTTER' using the UP or DOWN button.

Set 'SHUT TER' to the desired mode using the LEFT or RIGHT button.

OFF : Deactivation

FLK: Flicker mode

- NTSC (1/100)

- PAL (1/120)

Main Menu -

SHUTTER SPEED CONTROL(1)

AUTO IRIS LENS(DC TYPE)is recommended than MANUAL LENS.

Some lens can make a malfunction according to the BRIGHTNESS LEVEL.

NOTE

When DC LENS selected, press MENU button to control the BRIGHTNESS.

Brightness

Press SET to Return

BRIGHTNESS 25

Main Menu -

SHUTTER SPEED CONTROL(2)

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

MANUAL

AWC

HIGH

OFF

---

MANUAL : When setting shutter speed manually.(Only for manual LENS mode)

You can select speed from

- NTSC (x128~x2, 1/60~1/120,000 sec.)

- PAL (x128~x2, 1/50~1/120,000 sec)

SHUTTER

Press SET to Return

MANUAL 1/60

Main Menu -

DNR

6) DNR (Digital Noise Reduction)

DNR reduce the noise on the screen.

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

---

AWC

HIGH

OFF

---

P ress the MENU button to display the SETUP menu and move the arrow indicator to 'DNR' using the UP or

DOWN button.

SET 'DNR' to the desired mode using the LEF T or RIGHT button.

OFF : Deactivation

LOW : Low reduction

of the noise

MIDDLE : Middle

reduction of the noise

HIGH : High reduction

of the noise

Afterimage may appear with DNR

When selected 'AGC' menu OFF, DNR doesn't work.

If you change the 'AGC' menu from AGC-L to AGC-H, sensitivity is

increasing as well as noise on the screen.

NOTE

MANUAL : To fine adjust, select the Manual mode. You can increase or decrease the red

or blue factor while monitoring the difference on the screen. Set to 'MANUAL'

mode and press the MENU button, lncrease or decrease the value for RED(R-Gain)

and BLUE(B-Gain), watching the color of the picture, and press the MENU button

when you obtain the best color.

Proper White Balance may not be obtained under the following

conditions, in these cases select the AWC mode.

- When the scene contains mostly high color temperature object,

such as a blue sky or sunset.

- When the scene is dim.

- If your camera faces fluorescent lamp directly or is installed in the

place of the changing illumination.

NOTE

When completed, press 'MENU'

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

MANUAL

ESC

AWC

HIGH

OFF

---

ESC : You can control

the BRIGHTNESS.

Don't expose the camera to fluorescent lamp directly not to get unstable

image in the internal synchronization modes.

When the SHUTTER menu is set to FLK mode. SENS-UP can not work.

Please control the menu.

NOTE

Brightness

Press SET to Return

BRIGHTNESS 25

Main Menu -

AGC

5) AGC (Auto Gain Control)

AGC is to get bright picture. Higher GAIN level, getting brighter screen. But you can get noise increase.

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

---

AWC

HIGH

OFF

---

P ress the MENU button to display the SETUP menu and move the arrow indicator to 'AGC' using the

UP or DOWN button.

SET 'AGC' to the desired mode using the LEF T or RIGHT button.

OFF LOW MIDDLE HIGH

Main Menu -

BACKLIGHT

4) BACKLIGHT

When there is a strong backlight behind the object, clear images of the background as well as the object can

still be obtained by using the BACKLIGHT function.

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

---

AWC

HIGH

OFF

---

Press the MENU button to display the SETUP menu and move the arrow indicator to 'BACKLIGHT' using the UP or DOWN button.

SET 'BACKLIGHT' to the desired mode using the LEF T or RIGHT button.

OFF LOW MIDDLE HIGH

BLC OFF

7) SENS-UP (Sense-Up)

Digital Slow Shutter(DSS) makes camera's sensitivity up so you can always get the clear image with this

function under night or low lighting level.

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

---

AWC

HIGH

OFF

---

Press the MENU button to display the SETUP menu and move the arrow indicator to 'SENS-UP' using the

UP or DOWN button.

SET 'SENS-UP' to the desired mode using the LEF T or RIGHT button.

AUTO : When your

camera is under night

or low-lighting level.

Select this mode.

OFF : Deactivation

If you press MENU button at 'AUTO' menu, you can control the lowlight

action maximum magnifications. (x2~x128)

When increasing the magnifications in case of SENS-UP activated.

It may appear noise, spots, whitish, This is not out of order.

Expander the magnifications, you can get the brighter screen as well as the afterimage.

NOTE

Main Menu -

SENSE-UP

8) SPECIAL

SETUP

LENS

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

DNR

SENS-UP

SPECIAL

EXIT

---

AWC

HIGH

OFF

---

SPECIAL

CAMERA ID

COLOR

SYNC

MOTION DET

PRIVACY

MIRROR

SHARPNESS

RESET

RETURN

---

INT

OFF

Press the MENU button to display the SET UP menu and move the arrow indicator 'SPECIAL' using the UP or DOWN button.

SET 'SPECIAL' to the desired mode using the LEF T or RIGHT button.

Press the MENU button to display the SETUP menu and move the arrow indicator to 'CAMERA ID' using the UP or DOWN button.

SET 'ON' using the LEF T or RIGHT button.

Menu [SPECIAL]-

CAMERA ID (1)

CAMERA ID

SPECIAL

CAMERA ID

COLOR

SYNC

MOTION DET

PRIVACY

MIRROR

SHARPNESS

RESET

RETURN

---

INT

OFF

P ress the MENU button to display the setup menu and move the arrow indicator to 'COLOR' using the

UP and DOWN button.

: You can choose color and B/W mode electronically.(OPTION)

SET 'COL OR' to the desired mode using the LEFT or RIGHT button.

ON : Color mode

AUTO : Generally color

mode, B/W mode in

low luminance.

Menu [SPECIAL]-

COLOR

Menu [SPECIAL]-

SYNC

SPECIAL

CAMERA ID

COLOR

SYNC

MOTION DET

PRIVACY

MIRROR

SHARPNESS

RESET

RETURN

---

INT

OFF

P ress the MENU button to display the setup menu and move the arrow indicator to 'SYNC' using the

UP and DOWN button.

: Two Synchronization modes are available Internal and External Line-Lock.

In Line-Lock mode, it synchronous generator.

The line-lock synchronization is only used in the area of 60Hz (NTSC models)/ 50Hz(PAL Models)

SET to the desired mode using the LEF T or RIGHT button.

INT : Internal

synchronization

L/L : If you choose

'L/L', you can adjust

the desired phase.

- Press the MENU button.

- You can adjust the

desired phase from

0 to 359.

When it used in AC power, L/L mode can be used.

In DC12V, the SYNC menu sets 'INT' mode.

NOTE

SYNC

Menu [SPECIAL]-

PRIVACY

SPECIAL

CAMERA ID

COLOR

SYNC

MOTION DET

PRIVACY

MIRROR

SHARPNESS

RESET

RETURN

---

INT

OFF

P ress the MENU button to display the setup menu and move the arrow indicator to 'PRIVACY' using the

UP and DOWN button.

: To mask area which you want.

SET 'PRIV ACY' to the desired mode using the LEFT or RIGHT button.

OFF : Deactivation

ON : PRIVACY mode

activated

- Press the MENU button and

then set the area's bounds

with the method like MOTION DET. Set

- Set 'ON' using LEFT or

RIGHT button.

- Move the arrow indicator

to area you want to mask.

- Press the MENU button.

PRIVACY

Menu [SPECIAL]-

MIRROR

SPECIAL

CAMERA ID

COLOR

SYNC

MOTION DET

PRIVACY

MIRROR

SHARPNESS

RESET

RETURN

---

INT

OFF

P ress the MENU button to display the setup menu and move the arrow indicator to 'MIRROR' using the

UP and DOWN button.

SET 'MIRROR' to desired mode using the LEF T or RIGHT button.

OFF : Deactivation

ON : Reverse image

LEFT and RIGHT.

MIRROR

P ress the MENU button to access the SETUP mode.

Y ou can enter up to 15 characters.

• Move the cursor to character-enter location by using the LEFT or RIGHT button.

• Select the desired character by using the UP or DOWN button.

• Press the MENU button to confirm the blinking character. The first character is saved and the cursor

in the bottom of the screen moves to the next position.

• Repeat steps a, b and c until you create the full name you want.

• Select the position at which the CAMERA ID will be located on the screen.

- Move the cursor to 'POS' and press the MENU button.

Select the position by using the 4-directional buttons, then press the MENU button to confirm the position.

• When completed, move the cursor to 'END' and press the MENU button.

Menu [SPECIAL]-

CAMERA ID (2)

If the CAMERA ID feature is set to 'OFF', the name will not displayed in the monitor.

NOTE

If you make a mistake while entering name Move the cursor to 'CLR', press 'SET'

button. After erasing the character from right to left. Correct the character again.

NOTE

CAMERA ID

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

abcdefghijklm

nopqrstuvwxyz

. 0123456789

CLR POS END

_______________

Menu [SPECIAL]-

MOTION DETECTION

SPECIAL

CAMERA ID

COLOR

SYNC

MOTION DET

PRIVACY

MIRROR

SHARPNESS

RESET

RETURN

---

INT

OFF

Press the MENU button to display the setup menu and move the arrow indicator to 'MOTION DET' using the UP and DOWN button.

: Whenever your camera detects motion of object displaying 'MOTION DETECTED' with the number

counted up on the screen

SET 'MOTION DET' to the desired mode using the LEF T or RIGHT button.

OFF : Deactivation.

ON : MOTION DET.

Activated

- Set the areas you want

to observe.

- Move the arrow indicator

to 'AREA SET' using UP

and DOWN button, and

then press the MENU button.

- Press MENU button.

MOTION DET

MOTION DETECTION

Press SET to Return

AREA SEL

AREA STATE

TOP

DOWN

LEFT

RIGHT

AREA1

Menu [SPECIAL]-

SHARPNESS

P ress the MENU button to display the setup menu and move the arrow indicator to 'SHARPNESS' using

the UP and DOWN button.

SET 'SHARPNES S' to the desired mode using the LEFT or RIGHT button.

SPECIAL

CAMERA ID

COLOR

SYNC

MOTION DET

PRIVACY

MIRROR

SHARPNESS

RESET

RETURN

---

INT

OFF

OFF : Deactivation.

SHARPNESS

Press SET to Return

LEVEL

ON : SHARPNESS

control mode(level 0~31)

when the level is up, the

sharpness will make

image clear.

Please control the level

as you want to get.

If the level is to much high,

you can get the unnatural

image with noise.

General Dome Camera -

[B] Type

General Dome Camera -

[A] Type

Vandal Proof Dome Camera

Menu [SPECIAL]-

RESET / RETURN

RESET

: Save the setting of SPECIAL function, and then move to SETUP menu.

RETURN

: To reset your camera to factory default setting.

PRIVACY

Press SET to Return

AREA SEL

AREA STATE

AREA TONE

TOP

DOWN

LEFT

RIGHT

AREA1

SPECIAL

CAMERA ID

COLOR

SYNC

MOTION DET

PRIVACY

MIRROR

SHARPNESS

RESET

RETURN

---

INT

OFF

Max Min

MOTION DETECTION

Press SET to Return

AREA SEL

AREA STATE

TOP

DOWN

LEFT

RIGHT

AREA1

Owner's Manual

Guide Pattern

Service Monitor Cable

L-Wrench

Surface Mount Bracket

Tapping Screw

Surface Mount Screw

Flush Vandal Proof Dome Camera

Fixed Lens Type Vari-focal Lens Type

Connecting to Monitor and Power

Vandal Proof Dome Camera

Owner's Manual

Guide Pattern

Service Monitor Cable

Mounting Screw

L-Wrench

General Dome Camera

Owner's Manual

Guide Pattern

Service Monitor Cable

Mounting Screw

Stick the guide pattern on the wall or ceiling.

Adjust desired focus and scene by turning and moving

the 3-axis camera bracket by hand.

Drill four holes according to the guide pattern then

insert anchors into the drilled holes.

Put the dome cover over the base.

Fix the dome cover on the base by covering.

Fixed the camera to a celling using four screws.

Draw out power / video wires to the connecting places.

Guide Pattern

Ceiling

Dome Cover

Dome Base

Mounting

Screw

Stick the guide pattern on the wall or ceiling.

Adjust desired focus and scene by turning and

moving the 3-axis camera bracket by hand.

Drill four holes according to the guide pattern

then insert anchors into the drilled holes.

Draw out power / video wires to the

connecting places.

Put the dome cover over the base.

Fix the dome cover on the base by covering.

Fixed the camera to a celling using four screws.

Dome Cover

Guide Pattern

Dome Base

Mounting

Screw

Ceiling

Flush Vandal Proof Dome Camera

Stick the guide pattern on the wall or ceiling.

Connect the dome base to the surface mount

bracket by screws.

Draw out power / video wires to the

connecting places.

Connect the dome base to the surface mount

bracket by screws.

Drill four holes according to the guide pattern

then insert anchors into the drilled holes.

Fix the surface mount bracket by screws on

the ceiling.

Put the dome cover over the base.

Fix the dome cover on the base by L-Wrench.

Stick the guide pattern on the wall or ceiling.

Adjust desired focus and scene by turning and

moving the 3-axis camera bracket by hand.

Drill four holes according to the guide pattern

then insert anchors into the drilled holes.

Draw out power / video wires to the

connecting places.

Put the dome cover over the base.

Fix the dome cover on the base by L-Wrench.

Fixed the camera to a celling using four screws.

L-Wrench

Guide Pattern

Dome Base

Dome Cover

Mounting

Screw

Ceiling

Guide Pattern

Surface Mount

Bracket

Surface Mount

Screw

Tapping Screw

Dome Base

Dome Cover

L-Wrench

Tilt rotation: Adjusting the vertical angle.

Pan rotation: Adjusting the horizontal angle.

Horizontal rotation: Adjusting the horizontal position of the screen.

Tilt rotation: Adjusting the vertical angle.

Pan rotation: Adjusting the horizontal angle.

Horizontal rotation: Adjusting the horizontal position of the screen.

Focus handle: Focus (Far or Near)

Zoom handle: Zoom (Tele or Wide)

Camera Lay-out

No.

Function

Video Output

Power Input

Remark

1.0 Vp-p

AC24V(20V

28V)orDC12V(10V

15V), Max 4W/330mA

Terminal Color

Yellow

Green

Video

(Yellow)

Power- AC 24V/ DC 12V

(Green)

Video Output

GND

• The wire is non-polarized.

• Use AC 24V power source or DC 12V power source.

AC 24V/DC 12V Power Type

No.

Function

Video Output

Power Input

Remark

1.0 Vp-p

DC 12V(DC10V~15V), 180mA(Max)

Terminal Color

Yellow

Red

• The wire is polarized.

• Use DC 12V power source.

DC 12V Power Type

Video

(Yellow)

Power- DC 12V

(Red)

Video Output

GND

DOWN : Down Button

UP : Up Button

LEFT : Left Button

RIGHT : Right Button

MENU(SET) : Menu Button

Service Monitor Connecter : Use service monitor

connector to set camera angle & focus when installing.

VIDEO

UP LEFT

DOWN

J507

J503(AC 24V)

J504

AUDIO

J502

OUTPUT CABLE

J501

Problem Solutions

Nothing appears on the

screen.

The image on the screen

is dim.

The image on the screen

is dark.

The camera is not working

properly, and the surface

of the camera is hot.

The image on the screen

flickers.

• Check that the power cord and line connection between the camera and monitor

are fixed properly.

• Check that you have properly connected VIDEO cable to the camera VIDEO output jack.

• Is lens stained with dirt? Clean your lens with soft, clean cloth.

• Set the monitor to proper condition.

• If the camera is exposed to too strong light, change the camera position.

• Adjust the lens' focus properly.

• Adjust the contrast feature of the monitor.

• If you have an intermediate device, set the 75/ Hi-z properly .

• Adjust DC Level, VR Level properly.

• Check that you have properly connected the camera to an appropriate power source.

• Is the camera facing to direct sunlight or fluoresent lighting?

Change the camera position.

Simple to install

3-Axis bracket makes

adjustment easy.

The 3D bracket (Pan, Tilt and Horizontal)

allows the camera to be manually as well

as moved horizontally and vertically.

NOTE

Insert coin to the side hole and remove

the dome cover by twist coin.

. Vandal Proof Dome Camera

Flush Vandal Proof Dome Camera

CNB D2960N/D2960P Owner's manual

Brand: CNB

Model: D2960N/D2960P

Category: Security cameras

Type: Owner's manual

This manual is also suitable for

D2960NVD/D2960PVD

Download PDF

report

CNB D2960N/D2960P Owner's manual

This manual is also suitable for

CNB D2960N/D2960P Owner's manual

Related papers

Other documents