Wolf ICBDF484F Installation Instructions Manual

Brand: Wolf

Model: ICBDF484F

Category: Ovens

Type: Installation Instructions Manual

This manual is also suitable for

DUAL FUEL RANGES

INSTALLATION INSTRUCTIONS

Natural gas .

Leave instructions with the owner.

This cooktop is approved for use with

Model Series

ICBDF366

ICBDF304

ICBDF364C

ICBDF364G

ICBDF486C

ICBDF486G

ICBDF484CG

ICBDF484F

ICBDF606CG

ICBDF604CF

CMY

As you read this use & care information,

take particular note of the CAUTION and

WARNING symbols when they appear.

This information is important for safe and

efficient use of the Wolf equipment.

In addition, this use & care information may

signal an IMPORTANT NOTE which highlights

information that is especially important.

signals a situation where minor injury or

product damage may occur if you do not

follow instructions.

states a hazard that may cause serious

injury or death if precautions are not

followed.

WOLF

is a registered trademark of Wolf Appliance, Inc.

I N S TA L L AT I O N R E Q U I REME N T S

IMPORTANT NOTE: This installation must

be completed by a qualified installer,

service agency or gas supplier.

IMPORTANT NOTE:

Save these installation

instructions for the local inspec tor’s use.

Installation to be carried out only by an

authorised person.

Do not modify this appliance.

Please read the entire installat ion instruc-

tions prior to installation.

Installer:

please retain these instructions

for local inspector’s reference, then leave

them w ith the homeowner.

Homeowner:

please read and keep these

instructions for f uture reference and be sure

to read the entire use & care information

prior to use.

IMPORTANT NOTE:

This appliance m ust be

installed in accordance with local codes. The

correct voltage, frequency and amperage must

be supplied to the appliance from a dedicated,

grounded circuit which is protec ted by a

properly sized circuit breaker or time delay

fuse. The proper voltage, frequency, and

amperage ratings a re listed on the produc t

rating plate

Record the mo del and s erial numbers before

installing the dual fuel range. Both n umbers

are listed on the rating plate, located rear of

removable lower panel.

W O L F D U A L F U E L R A N G E S

IMPORTANT NOTE:

Instal lation and service must be

perfor med by a qualified installer,

servic e agency or the gas supplier.

Do not store or us e gasoline or

other flammable vapors and liquids

in the vicinity of this or an y other

applianc e.

A ventilation hood is recomme nded

for use with the Wolf dual fuel range.

WHAT TO DO IF YOU SMELL GAS:

Do not try to ligh t any appliance.

Do not touch any electrical switc h.

Do not use any phone in your

building.

Immediately call your gas supplier

from a neighbor

’s phon e. Follow the

gas supplier’s instructions.

If you cannot reach your gas

supplier, call the fire departm ent.

If the information in this book is

not followed exactly, a fire or

explosion may result, causing

property damage, personal injury

or death.

R A T I N G P L A T E

I N F O R M A T I O N

Model Number

Serial Number

IMPORTANT NOTE:

Statutory requirements: This

applia nce shall be installed in

accordance with the manufac-

turer’s insta llation instructions,

local g as fitting regulations,

municipal building codes, electri-

cal wiring regula tions, and

AS/NZ5601 the Aust ralian Standard

for gas installations. Refer also to

AS/NZ5601 for gas pipe sizing

tables.

Unsuitability for use in marin e

craft, caravans or mobile homes,

unless each burne r is fitted with a

flame safeguard.

CO N TACT

IN F OR M ATIO N

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street

Melbourne Victoria 3000

Phone 03 9600 2218

subzero-wolf.com.au

B E F O R E Y O U S T A R T

Proper installation is your responsibi lity.

Installations must be performed by a

qualified or licensed contractor, plumber or

gas fitter, qualified or li censed by the state,

province or region where this applian ce is

being installed. You must also ensure that

electrical insta llation i s adequate and

conforms with all local codes and

ordinan ces.

Proper gas supply must be a vailable; refer

to gas supply requirements on page 9.

Electri cal ground is requi

red; see electrical

requirements on page 10.

Check the location where the range will be

installed. The location should be away from

strong draft areas, such as windows, doors

and strong heating vents or fans. Do not

obstruct the flow of ai r. The area in whi ch

you are installing this appliance must have

an adequate supply of fresh air to ensure

proper combustion and ventilation.

Make sure you have everything necessary

for proper installation. It is the responsibil-

ity of the i

nstaller to comply with the instal-

lation clearances specified on the product

rating plate. The rating plate is located rear

of removable lo wer panel.

All openings in the wall or floor where the

range is to be installed must be se aled.

The cooking ran ge to be installed only on

the floor.

When installing the range under existing

cabinets where the installation does not

meet the minimum cabinet clearances,

install a ventilation hood or other non-

combustible surface above th

e range to

avoid burn hazards. R efer to minimum

clearances on page 3.

V E N T I L AT I O N O P T I O N S

IMPORTANT NOTE:

A suitable ventilation

hood must be installed. We recommend a Wolf

Pro Ventilation Hood be installed with the Wolf

dual Fuel Range. Contact your Wolf dealer for

details.

IMPORTANT NOTE:

When installing a ventila-

tion hood, refer to the specific requirements

of the hood for the minimum dimension to

countertop.

I N S TA L L AT I O N S P E C I F I C A T I O N S

Wolf dual fuel ranges come in 762 mm,

914 mm, 1219 mm and 1524 mm wi dths.

Illustrations on pages 4–

7 provide the overall

dimensions and installation specifications for

each width of dual fuel range.

Each range is designed to f it between cabinets

set at the distance specified by the unit. For

example, a 914 mm range will fit a 914 mm

opening. The exception is the 1524 mm un it

which will require a 1530 mm opening.

IMPORTANT NOTE:

Cabinet opening dimen-

sions shown in the installation specifications

illustrations must be used. These dimensions

provide for required clearanc

es.

Each unit is designed with a terminal block on

the rear of the range. Have a qualified electri-

cian or install er wire your unit from the electri-

cal supply, through the knockout in the unit

base and to the terminal block on the range.

IMPORTANT NOTE:

Locate the electrical

supply within dimensions shown in the

installation specifications illustrations and

flush with back wall.

Refer to the instal lation specifications illustra-

tion for your model on pages 4–7 for the ex

act

rough opening dimensions and location of the

gas supply and electrical.

Wolf dual fuel ranges using natural gas will

operate up to an altitude o f 2438 m without

any adjustment. Natural gas and LP gas instal-

lations from 2438 m to 3353 m need the high

altitude conversion kit.

I N S TA L L AT I O N I N S T R U C T I O N S

I N S TA L L AT I O N S P E C I F I C A T I O N S

M I N I M U M C L E A R A N C E S

IMPORTANT NOTE:

Caution must be use d in

planning the proper installation of the Wolf

dual fuel range to avoid fire or damag

e to

adjacent cabinetry or kitchen equipment.

Be sure to follow the minimum clearances

established in the finished rough opening

dimensions.

For insta llation against a rear combustible

surface a 25 4 mm classic stainless steel riser

must be used. Refer part nu mber 804387.

Refer to the installation specificatio ns illust ra-

tion for your model on pages 4–7 for the ex act

rough opening dimensions.

Maintain the following clearances to

combustible materials:

Minimum 457 mm clearance from bottom

of upper cabine t to countertop, within

152 mm minim um side clearance.

Minimum 762 mm clearance between coun-

tertop and bottom of wood or metal

cabinet, which is protected by not less than

6 mm flame retardant millboard covered

with not less than No. 28 MSG sheet steel,

.4 mm stainless steel , or .6 mm aluminum

or .5 mm copper.

Minimum 914 mm clearance between coun-

tertop and bottom of an unprotected wood

or metal cabinet.

Bottom of ventilation hood m ust be

600 mm minimum to 914 mm m aximum

from countertop.

I S L A N D | P E N I N S U L A I N S T A L L A -

T I O N S

For island installations,

the range should

not be installed within an enclosure having an

adjacent rear wall less than 305 mm from the

rear of the unit that rises above the counte rtop.

For peninsula installations,

the range must

have a 152 mm minimum clearance to the side

wall, left or right side, and 305 mm minimum

clearance to the rear wall.

Refer to the installation specificatio ns illustra-

tion for your model on pages 4–7 for the exact

rou

gh opening dime nsions.

Failure to locate the range without the

proper clearances will result in a fire

hazard.

ICBDF304

O L F

330 mm

LOCATION OF

ELECTRICAL

914 mm

937 mm

COOKING

SURFACE

1120 mm min

COUNTERTOP TO

COMBUSTIBLE

MATERIALS

VENTILATION HOOD

457 mm min

TO COUNTERTOP

LOCATION OF GAS AND

ELECTRICAL EXTENDS 57 mm

ON FLOOR F

ROM BACK WALL

762 mm

FINISHED ROUGH

OPENING WIDTH

83 mm

216

254 mm

LOCATION

OF GAS

SUPPLY

750 mm min TO

1120 mm max

TO BOTTOM OF

VENTILATION HOOD

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGE TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

0 mm TO NON-COMBUSTIBLE MATERIALS

330 mm

max

152 mm

min TO

COMBUSTIBLE

MATERIALS

(BOTH SIDES)

759 mm

OVERALL WIDTH

937

ISLAND

TRIM

1165

WITH

254 mm

RISER

1419

WITH

508 mm

RISER

1038

WITH

127 mm

RISER

1194 mm

664 mm

635 mm

613 mm

699 mm

235

749 mm

OVERALL DEPTH

*937 mm MIN TO 991 mm MAX.

911

937 mm

OVERALL

HEIGHT TO

COOKING

SURFACE*

Overall Width 759 mm

Overall Height

(to cooking surface) 937 mm

Overall Depth 749 mm

Opening Width 762 mm

D U A L F U E L R A N G E

IMPORTA NT N OTE: In non-island applications,

a m inimum 127 mm riser is required for model

ICBDF304.

Note A:

Side clearances. If the distance

measured from the periphery of the

nearest burner to any vertical surface

is less than 200 mm, the surface shall

be protected in accordance with

AS/NZ5601.

Note B:

The rangehood fitted above the

cooktop must be installed according

to the installation instructions for

the rangehood. A minimum

distance of 750 mm is required for a

range hood and 750 mm for an

exhaust fan

I N S TA L L AT I O N I N S T R U C T I O N S

483 mm

LOCATION OF

ELECTRICAL

914

937 mm

COOKING

SURFACE

VENTILATION HOOD

457 mm min

TO COUNTERTOP

LOCATION OF GAS AND

ELECTRICAL EXTENDS 76 mm

ON FLOOR FROM BACK WALL

914 mm

FINISHED ROUGH OPENING WIDTH

83 mm

216

381 mm

LOCATION

OF GAS

SUPPLY

mm min TO

1120mm max

TO BOTTOM OF

VENTILATION HOOD

1120 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

762 mm min

FOR CHARBROILER

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGE TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

330 mm

max

911 mm

OVERALL WIDTH

1194 mm

699 mm

235

749 mm

OVERALL DEPTH

*937 mm MIN TO 991 mm MAX.

911

937 mm

OVERALL

HEIGHT TO

COOKING

SURFACE

613 mm

664 mm

635 mm

I N S T A L L A T I O N S P E C I F I C A T I O N S

O V E R A L L D I M E N S I O N S

Overall Width 911 mm

Overall Height

(to cooking surface) 937 mm

Overall Depth 749 mm

Opening Width 914 mm

Dimensions may vary to

3 m m.

9 1 4 m m D U A L F U E L R A N G E S

M O D E L I C B D F 3 6 6

M O D E L I C B D F 3 6 4 C

M O D E L I C B D F 3 6 4 G

IMPORTA NT N OTE: In non-island applications,

a m inimum 127 mm riser is required for model

ICBDF366 and minimum 254 mm riser required for

models ICBDF36 4C and ICBDF364G installed against

a combustible surface. The island trim and 127 mm

riser may only be used against a non-combu stible

surface for models ICBDF364C and ICBDF364G.

NOTE

Note A:

Side clearances. If the distance

measured from the periphery of the

nearest burner to any vertical surface

is less than 200 mm, the surface shall

be protected in accordance with

AS/NZ5601.

Note B:

The rangehood fitted above the

cooktop must be installed according

to the installation instructions for

the rangehood. A minimum

distance of 750 mm is required for a

range hood and 750 mm for an

exhaust fan

750

50 mm TO NON-COMBUSTIBLE MATERIALS

937

ISLAND

TRIM

1165

WITH

254 mm

RISER

1419

WITH

508 mm

RISER

1038

WITH

127 mm

RISER

W O L F D U A L F U E L R A N G E S

330 mm

LOCATION OF

ELECTRICAL

914

937 mm

COOKING

SURFACE

VENTILATION HOOD

LOCATION OF GAS AND

ELECTRICAL EXTENDS 76 mm

ON FLOOR FROM BACK WALL

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGE TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

1219 mm

FINISHED ROUGH OPENING WIDTH

610 mm

83 mm

254 mm

LOCATION

OF GAS

SUPPLY

457 mm min

TO COUNTERTOP

mm min TO

1120 mm max

TO BOTTOM OF

VENTILATION HOOD

1120 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

762 mm min

FOR CHARBROILER

330 mm

max

1216 mm

OVERALL WIDTH

1194 mm

699 mm

235

749 mm

OVERALL DEPTH

*937mm MIN TO 991mm MAX.

911

937 mm

OVERALL

HEIGHT TO

COOKING

SURFACE

613 mm

664 mm

635 mm

I N S T A L L A T I O N S P E C I F I C A T I O N S

O V E R A L L D I M E N S I O N S

Overall Width 1216 mm

Overall Height

(to cooking surface) 937 mm

Overall Depth 749 mm

Opening Width 1219 mm

Dimensions may vary to

3 mm.

1 2 1 9 m m D U A L F U E L R A N G E S

GC8 44FDBCI

I C B D F 4 8 4 F

C8 64FDBCI

I C B D F 4 8 6 G

IMPORTANT NOTE: In non-island applications, a

minimum 254 mm riser is required for all 1219 mm

models installed against a combustible surface.

The island trim and 127 mm riser may only b e used

against a non-combustible su rface.

NOTE

Note A:

Side clearances. If the distance

measured from the periphery of the

nearest burner to any vertical surface

is less than 200 mm, the surface shall

be protected in accordance with

AS/NZ5601.

Note B:

The rangehood fitted above the

cooktop must be installed according

to the installation instructions for

the rangehood. A minimum

distance of 750 mm is required for a

range hood

and 750 mm for an

exhaust fan

NOTE

750

50 mm TO NON-COMBUSTIBLE MATERIALS

937

ISLAND

TRIM

1165

WITH

254 mm

RISER

1419

WITH

508 mm

RISER

1038

WITH

127 mm

RISER

I N S TA L L AT I O N I N S T R U C T I O N S

330 mm

LOCATION OF

ELECTRICAL

914

937 mm

COOKING

SURFACE

VENTILATION HOOD

LOCATION OF GAS AND

ELECTRICAL EXTENDS 76 mm

ON FLOOR FROM BACK WALL

83 mm

787 mm

254 mm

LOCATION

OF GAS

SUPPLY

1530 mm

FINISHED ROUGH OPENING WIDTH

457 mm min

TO COUNTERTOP

mm min TO

1120 mm max

TO BOTTOM OF

VENTILATION HOOD

1120 mm min

COUNTERTOP

TO COMBUSTIBLE

MATERIALS

762 mm min

FOR CHARBROILER

ISLAND INSTALLATIONS: 305 mm MINIMUM

CLEARANCE FROM BACK OF RANGE TO

COMBUSTIBLE REAR WALL ABOVE COUNTERTOP–

330 mm

max

1527 mm

OVERALL WIDTH

1194 mm

613 mm

664 mm

635 mm

699 mm

235

749 mm

OVERALL DEPTH

*937 mm MIN TO 991 mm MAX.

911

937 mm

OVERALL

HEIGHT TO

COOKING

SURFACE

I N S T A L L A T I O N SPE C I F I C AT I O N S

O VERA L L D I M E N S I O N S

Overall Width 1527 mm

Overall Height

(to cooking surface) 937 mm

Overall Depth 749 mm

Opening Width 1530 mm

Dimensions may vary to

3 m m.

1 5 2 4 m m D U A L F U E

I CBD F 6 0 6 C F

L R A N G E S

IMPORTA NT N OTE: In non-isla nd applications, a

minimum 254 mm riser is required for all 1524 mm

models installed again st a combustible surface.

The island trim and 127 mm riser may only be used

against a non-combustible surface.

NOTE

Note A:

Side clearances. If the distance

measured from the periphery of the

nearest burner to any vertical surface

is less than 200 mm, the surface shall

be protected in accordance with

AS/NZ5601.

Note B:

The rangehood fitted above the

cooktop must be installed according

to the installation instructions for

the rangehood. A minimum

distance of 750 mm is required for a

range hood and 750 mm for an

exhaust fan

750

FC4 06FDBCI

50 mm TO NON-COMBUSTIBLE MATERIALS

937

ISLAND

TRIM

1165

WITH

254 mm

RISER

1419

WITH

508 mm

RISER

1038

WITH

127 mm

RISER

U N PA C K T H E R A N G E

Remove and discard all packing materials,

including cardboard and tape on the outside of

the range and inside the oven cavity.

Remove the box containing the oven racks,

oven rack guides and broiler pan from inside

the oven cavity. Be sure to do this for both

oven cavities on the 1524 mm range.

Remove the burner grates and styrofoam off

the top cooking surface. Be sure to remove the

burner caps packaged in styrofoam below the

burner grates.

Do not discard the angle iron supplied with the

range. This is the anti-tip bracket and must be

installed with the unit. Refer to anti-tip bracket

installation on page 11.

Carefully lift the range off the pallet and

remove the styrofoam from the bottom of the

unit.

IMPORTANT NOTE:

Before moving the range

into position, protect any finished flooring with

appropriate materials to avoid damage to the

floor.

The rear of the range has rolling casters which

allows for easy movement of the range by

picking up on the front of the unit. Refer to the

illustration below.

The dual fuel range comes from the factory at

an overall height of 911 mm from floor to the

top of the bullnose, before any height adjust-

ment. The legs and casters allow for 54 mm

height adjustment. Refer to the illustration

below. Use a 19 mm socket to adjust the rear

casters. Refer to the installation specifications

illustration for your model on pages 4–7 for

additional dimensions.

W O L F D U A L F U E L R A N G E S

Casters allow for 54 mm

height adjustment

Rolling casters.

Do not lift the range by the oven door

handle(s). This will damage the oven door

and hinges.

The dual fuel range is very heavy. Use

caution when lifting and moving the unit.

Secure oven door(s) closed before

moving the unit.

O V E N D O O R R E M O V A L

If removal of the oven door(s) is necessary, a

hinge pin, supplied with the range, will need to

be inserted in the appropriate hinge arm. For

each oven door, only one hinge arm is spring

loaded, requiring use of the hinge pin for

removal of the oven door. The hinge pin will

be found taped to the inside of the oven door.

For 762 mm and 914 mm ranges, the hinge pin

will be inserted through the hole in the right

hinge arm (facing the unit). On 1219 mm and

1524 mm ranges, the spring hinges are located

on the outer edges of the unit. On these units,

the left oven door will have the spring hinge

on the left side and the right oven door will

have the spring hinge on the right side. Refer

to the illustrations below for the location of the

spring hinge(s) for your model.

Place Hinge Pin on

Spring Hinge Side of Door

Place Hinge Pins on

Spring Hinge Side of Door

Spring hinge location for 762 mm

and 914 mm ranges.

Spring hinge locations for 1219 mm

and 1524 mm ranges.

Failure to insert the hinge pin in the

appropriate hinge arm will cause damage

to the range. Minor injuries may occur.

IMPORTANT NOTE:

The oven door(s) should

not be removed unless it is necessary to fit the

range through a tight doorway. Door removal

should only be done by a qualified service

technician or installer. Door removal and rein-

stallation may cause damage to the oven

porcelain interior.

O V E N D O O R R E M O V A L

If removal of the oven door(s) is necessary,

follow these steps:

Remove the lower kickplate assembly to

access the lower hinge retainer mounting

screws.

Open the oven door to its fully opened

position and remove both upper and lower

hinge retainer mounting screws. The oven

gasket may have to be moved slightly to

access the bottom screws.

After removing the mounting screws, move

the hinge retainer plate forward slightly.

The hinge retainer plate will re

main on the

door hinge assembly after the mounting

screws have been removed.

Insert the supplied door hinge pin through

the hole in the appropriate hinge arm. Refer

to the illustration below.

Carefully close the oven door to about a

60° angle from horizontal and lift the door

away from the oven. A slight rocking

motion may be required for removal.

For 1219 mm and 1524 mm ranges,

complete these steps for both oven doors

IMPORTANT NOTE:

The dual fuel range must

be connected to a re

gulated gas supply.

The rating plate, located rear of removable

lower panel, has information on the type of

gas that should be used. If this information

does not agree with the type of gas available,

check with the local gas supplier. A duplicate

plate can be attached to the inside top of an

adjacent cupboard.

This appliance appliance must be installed in a

position with the proper level of ventilation. Do

not obstruct the flow of combustion and venti-

lation air.

The gas pressure regu

lator supplied with the

appliance must be installed in line with the gas

pipe. (N.G. only).

If the appliance cannot be adjusted to perform

correctly contact Multyflex or the local gas

utility. For service contact telephone number

please refer page 13.

For pressure testing in excess of 3.5 kPa (1/2”

psig) the appliance and its individual shut-off

valve must be disconnected from the gas

supply piping system. For pressure testing of

the gas piping system at pressures equal to or

less than 3.5

kPa (1/2”psig) the appliance must

be isolated from the gas supply system by

closing its individual shut off valve during any

pressure testing.

The appliance should not be connected to a

combustion product evacuation system.

Instruct the user in the operation of the appli-

ance before leaving..

EXPLOSION HAZARD —

Securely tighten all gas c onnections.

Failure to do so can result in explosion,

fire or death.

G A S S U P P LY R E Q U I R E MEN T S G A S S U P P LY C O N N ECT I O N

I N S TA L L AT I O N I N S TRU C T I O N S

Hinge

Retainer

Plate

Upper Mounting

Screw

Hinge

Kickplate

Oven door removal.

Do not lift or carry the oven door by the

door hand le.

Never test for a gas leak with a match or

other flame.

Gas connection:

The cooktop is adjusted to operate on the gas

type specified on the gas type label located on

the bottom of the unit. If in doubt as to the

type of gas available contact the network

operator or gas supplier for confirmation of

gas type.

The cooktop must be

connected to the gas

supply with upstream

connection of an isola-

tion valve in accordance

with the respectively

valid regulations. We

recommend that the

isolation valve be fitted

prio

r to the cooktop to

enable isolation of the cooktop from the gas

supply. The valve must be easily accessible at

all times.

This appliance may be connected with a hose

assembly, class B or class D in accordance to

AS/NZS 1869. If connected with a hose assemb

supply connection point is

accessible

with the appliance installed.

The position of the inlet connection is

measured from bottom RH rear of unit,

75 mm centre line from rear and 300 mm

centre line from RH side.

Fit regulator (N.G.) or Propane fitting (Propane)

directly to the R1/2” connection. direction for

gas flow is indicated on the rear of the regula-

tor.

Check correct operation of each burner individ-

ually and in combination. Burner flames should

be clear blue, with no yellow tipping. If the

burners show any abnormality check that

burner heads are correctly located and refer to

the ‘trouble shooting’ guide on page 26 & 27 of

the Use and Care manual. If satisfactory

performance can not be obtained, co

ntact

Sub-Zero Group Australia or the local gas utility.

For service

contact number refer page 13 of

this booklet.

Note: These burner have no aeration adjust-

ment.

It should be expressly noted that we cannot

accept any liability for direct or indirect damage

caused by wrong connection or improper instal-

lation. When being repaired, the appliance must

always be

disconnected

from the main

gas and electric-

ity supply; if

required,notify

our customer

service.

ensure that the gas

W O L F D U A L F U E L RA N G E S

I M PO R T AN T N O T E

Be aware o f local code s and ordinances

when insta lling you r service.

ELECTRICAL REQUIREMENT S

G A S R A T I N G

G A S RATIN G

Refer to page 13

R E Q U I R E D P O W E R S U P P L Y

Single phase: 220-240V AC; 50/60 Hz

3phase: 380-415V AC; 50/60 Hz

M A X I M U M C O N N E C T E D L O A D

762 mm and 914 mm Dual Fuel ranges:

Single phase: 19 amps

3phase: 18 amps

1219 mm Dual Fuel ranges:

Single phase: 35 amps

3phase: 18 amps

1524 mm Dual Fuel ranges:

Single phase: 38 amps

3phase: 18 amps

Refer to the wiring diagram showing the connections

for each lead to the terminal box on the unit.

The complete appliance must be properly

grounded at all times when electrical power is

applied.

NOTE: Improper connection can result in a

hazard.

Before obtaining access to terminals, all supply

circuits must be disconnected.

Verify that power is disconnected from the

electrical box before proceeding.

Open the terminal box to expose the screws with

corresponding numbers. Run the cord through the

strain relief hole and into the terminal box.

For Single Phase Install (Line, Neutral, Ground):

Loosen the 1, 5, and ground screws. Attach the

Neutral wire to the number 5 position. Line should be

attached to the 1 postion and attach the ground to

the corresponding ground screw.

For 3phase Install (L1, L2, L3, Neutral, Ground):

Loosen the 1, 2, 3 and remove the copper bars.

Loosen 5 and ground screws. Attach L1 to position

1. L2 to position 2. L3 to position 3. Neutral wire to

position 5 and attach the ground to the correspond-

ing ground screw.

IMPORTANT NOTE:

Connection of this appliance

should be through a fused connection unit or a

suitable isolator, which complies with national and

local safety regulations. The o

switch should

be easily accessible after the appliance has been

installed. If the switch is not accessible after installa-

tion (depending on country) an additional means of

disconnection must be provided for all poles of the

power supply. When switched

there must be an

all pole contact gap of 3 mm in the isolator switch.

This 3 mm contact disconnect gap must apply to

any isolator switch, fuses and/or relays according to

EN60335.

Copper bars must be removed from positions 1,

2, and 3 when connecting to 3phase power.

Single phase wiring diagram

3phase wiring diagram

DRYWALL APP L ICATION S

After properly positioning the anti-tip bracket, use wall

anchors to fasten it to the wall. Using a Philips screwdriver

or a low rpm screw gun, drive the anchor into the surface

of the wallboard until the two cutting blades penetrate the

surface. Use gentle forward pressure to rotate the collar until

flush with the surface of the wall. Refer to the illustrations

below. Use #8 screws and flat washers to fasten the anti-tip

bracket to the wall.

IMPORTANT NOTE:

Pre-drill holes if difficulty is encoun-

tered during installation of the wall anchor. For hard wall-

board or double-board construction, use a 6 mm drill bit. For

solid plaster, use a 11 mm drill bit.

WOO D F LOO R APP L ICATION S

After properly positioning the anti-tip bracket, drill 5 mm pilot

holes

through the floor. Use #12 screws and flat washers to

secure the bracket to the floor.

C ONC R E TE FLOO R A P PLICATIO N S

After properly positioning the anti-tip bracket drill 10 mm

holes into the concrete a minimum of 38 mm deep. Use 10

mm wedge anchors to secure the bracket to the floor.

ANTI- T IP BOLT ADJUSTMENT

Once the bracket is secured in place, adjust the anti-tip bolt

at the back of the range so the top of the washer is 22 mm

maximum from the floor. Slide the range into the opening and

verify the anti-tip bolt is engaged. Refer to the illustrations

below.

IMPORTANT NOTE:

The top of the range must be level.

Use the adjustable front legs and the rear casters to level

the range.

Raise the unit to its desired height by adjusting the front

legs and rear casters. The legs and casters allow for 54 mm

height adjustment. Use a 19 mm socket to adjust the rear

casters. The front legs are adjusted by rotating the bottom

hexagonal portion of the leg.

The anti-tip bracket can be installed by securing it to the wall

or floor using the supplied hardware.

Refer to the chart and illustration below to determine the

proper distance from the left side of the opening to the

anti-tip bracket. This will ensure the anti-tip bolt properly

engages the bracket.

MODEL A

762 mm Range 5 mm

914 mm Range 14 mm

1219 mm Range 5 mm

1524 mm Range 8 mm

A N TI- TIP BRACKET INS TALLATI O N

O VEN D OOR REI N S TALLATIO N

IMPORTANT NOTE:

The oven door(s) should not be removed

unless it is necessary to fit the range through a tight

doorway. Door removal should only be

done by a qualified

service technician or installer. Door removal and reinstalla-

tion may cause damage to the oven porcelain interior.

ANTI-TIP

BRACKET

Anti-tip bracket location.

ANTI-TIP

BRACKET

WALL

ANCHOR

Wall anchor installation.

22 mm MAX

ANTI-TIP

BOLT

Anti-tip bolt adjustment.

ANTI-TIP

DEVICE

ENGAGED

Anti-tip bolt engaged.

Hinge

Retainer

Plate

Upper Mounting

Screw

Hinge

Kickplate

Oven door reinstallation.

If oven door(s) have been removed, follow these steps to

reinstall:

Hold the oven door on both sides and position it with

door hinges aligned with openings in the oven frame.

Holding the oven door at an approximate 30° angle from

vertical, slide the hinges into the openings until the

bottom hinge arms drop fully into the hinge receptacles.

Open the oven door to its fully opened position. Remove

the hinge pin from the appropriate hinge arm. Refer to

the

illustration below.

Reinstall the hinge retainer plate with upper and lower

mounting screws.

Open and close the door completely to ensure that it is

properly installed.

For 1219 mm and 1524 mm ranges, complete these steps

for both oven doors.

Reinstall the lower kickplate assembly.

IMPORTANT NOTE:

Fully extend the hinge claw which is

opposite the hinge pin location and insert into the hinge

pocket prior to inserting opposite side.

This will ease the

installation of the oven door.

This range can tip. Injury to persons could result.

Install the anti-tip bracket supplied with the range.

Do not lift or carry the oven door by the door handle.

I N S TALL AT I O N INS TRU C TIONS

W O L F D U A L F U E L R A N G E S

R E M O V I N G T H E R A N G E

If removing the dual fuel range is necessary for

cleaning or service, shut off the gas supply.

Disconnect the gas supply and electrical

connections to the unit, then remove the

range. Reinstall in the reverse order and be

sure to check the gas connection for leaks.

Refer the Wolf dual fuel ranges use & care

information included with the range for

cleaning recommendations.

T R O U B L E S H O O T I N G

IMPORTANT NOTE:

If the dual fuel range

does not operate properly, follow these

troubleshooting steps:

Verify that power is being supplied to the

range.

Check the gas supply and electrical

connections to ensure that the installation

has been completed correctly.

Check that gas valves are turned to the ON

position.

Follow troubleshooting procedures as

described in the Wolf dual fuel ranges

use & care information.

If the range still does not work, contact a

Wolf dealer. Do not attempt to repair the

range yourself. Wolf

is not responsible for service required to

correct a faulty installation.

Be sure to disconnect the gas supply and

electrical connections before removing

the range.

V E R I F Y R A N G E O P E R A T I O N

IMPORTANT NOTE:

Prior to operating

the range, be sure to read the entire

Wolf dual fuel ranges use & care infor-

mation included with the range for

important safety and service informa-

tion.

Install the oven rack guides onto the

shoulder screws located on the interior

side walls of the oven. Slide the oven

racks onto the support racks within the

oven. There are three racks per oven,

except for the 457 mm oven which has

two racks. Place the broiler pan and grid

on a rack within the oven, if desired.

Turn on the power supply to the range.

The control panel should be closed (no

visible control pads). Touch and slightly

depress the flame graphic on the hidden

control panel to open.

Set the time of day by pressing the

touch pad, scroll to the desired time by

using the or arrows, then touch

. After setting the time, the hidden

control panel can be closed. The control

panel does not have to be open to

operate the oven.

Select any of the eight cooking modes

by using the oven control knob bezel

and turning to the desired mode. Once

the mode has been selected, the temper-

ature can be adjusted by turning the

temperature readout knob clockwise to

increase the temperature or counter-

clockwise to decrease the temperature.

Verify that the oven is coming up to

temperature. For a 1219 mm or 1524 mm

range, follow this procedure for the both

ovens.

IMPORTANT NOTE:

A small amount of

smoke and odor may be noticed during

the initial break-in period. Refer to the

use & care information for additional

information.

C O O K T O P O P E R AT I O N

The cooktop burner uses an electronic igniter in

place of a standing pilot. When the cooktop control

knob is pushed in and turned to the position,

the system creates a spark to light the burner. This

sparking continues for 4 seconds or until the elec-

tronic ignition senses a flame, which ever comes

first. If the igniter fails to ignite the gas in 4 seconds,

the gas safety shutoff valve will close, eliminating

the gas flow for 5 seconds. The valve will reopen

after the purge time of 5 seconds, and the igniter

will automatically attempt to re-ignite the gas. This

cycle of events is attempted 3 times. After the third

attempt, in order for gas to flow to the burner once

again, the user must return the knob to the

position and then turn the knob to the

position.

To check operation of the cooktop burner, push in

and turn the control knob to the position. The

flame should light within four seconds.

If the burner does not light properly, turn the control

knob to the position. Check that the burner

head is in the proper position. Check that the power

supply cord is plugged in and that the circuit breaker

or house fuse has not blown.

Check operation again; If flame is not established

within the ignition cycle time, release the knob, open

a door and wait 1 minute before attempting a new

ignition procedure.

If the flames are extinguished - for any reason

whatever - turn OFF the control knob and wait at

least 1 minute before retrying to ignite the burner.

Ensure that the flames do not extinguish when you

reduce to low flame quickly. Check correct operation

of each burner individually and in combination.

F L A M E H E I G H T A N D A P P E A R A N C E

The flame on natural gas should be blue with a

deeper blue core. and no yellow tipping. If burners

show any abnormality check that burner heads are

correctly located and refer to the ‘ trouble shooting

guide’ on this page. If satifactory performance can

not be obtained, contact Multyflex. For service

contact number refer page 13 of this booklet.

IMPORTANT NOTE:

Initial lighting of the surface

burners may take slightly longer, as air in the

system must be purged before gas can be supplied

to the burner.

W I R I N G D I A G R A M

The wiring diagram covering the control circuit

is located rear of the removable lower panel.

The information and images in this book are the

affiliate of Sub-Zero, Inc. Neither this book nor any

information or images contained herein may be

copied or used in whole or in part without the

express wri tten permission of Wolf Appliance, Inc.,

an affiliate of Sub-Zero, Inc.

I N S TA L L AT I O N I N S T R U C T I O N S

S E R V I C E I N F O R M A T I O N

When requesting information, literature,

replacement parts or service, always refer to

the model and serial number of your dual fuel

range. This information is found on the

product rating plate located rear of the remov-

able lower panel. Refer to the illustration below.

Record the rating plate information

below for future reference.

Model Number

Serial Number

Installation Date

Wolf Dealer and Phone

B E F O R E C A L L I N G F O R S E R V I C E

Before calling y

our Wolf dealer, refer to the

troubleshooting guide on page 12. Check

the household fuse or circuit breaker to see if it

has been blown or tripped and that the electri-

cal connection to the appliance has not been

disconnected. A power outage may also have

caused a disruption in service.

For service call:

1300 808 859

Made in USA

GSCS20230

SAI GLOBAL

AS4551

Electrical compliance: in accordance with

AS/NZS3100 240 V AC, 4.5 kW/19 Amps, 50 Hz

Model

No:

ICBDF304

Serial No:

Gas

type

LPG

Test point press. (kPa) 1.0 2.75

Injector sizes (mm)

RHF

RHR

LHF

LHR

1.80

1.35

1.09

0.89

Total Consumption (MJ/h) 51.0 51.1

MF027

Made in USA

GSCS20230

SAI GLOBAL

AS4551

Electrical compliance: in accordance with

AS/NZS3100 240 V AC, 4.5 kW/19 Amps, 50 Hz

Model

No:

ICBDF366

Serial No:

Gas

type

LPG

Test point press. (kPa) 1.0 2.75

Injector sizes (mm)

RHF/CF

RHR/CR

LHF

LHR

1.80

1.35

1.09

0.89

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street Melbourne

Victoria 3000 +61 3 9600 2218

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street Melbourne

Victoria 3000 +61 3 9600 2218

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street Melbourne

Victoria 3000 +61 3 9600 2218

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street Melbourne

Victoria 3000 +61 3 9600 2218

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street Melbourne

Victoria 3000 +61 3 9600 2218

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street Melbourne

Victoria 3000 +61 3 9600 2218

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street Melbourne

Victoria 3000 +61 3 9600 2218

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street Melbourne

Victoria 3000 +61 3 9600 2218

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street Melbourne

Victoria 3000 +61 3 9600 2218

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street Melbourne

Victoria 3000 +61 3 9600 2218

otal Consumption (MJ/h) 79.0 79.1

MF022

Made in USA

GSCS20230

SAI GLOBAL

AS4551

Electrical compliance: in accordance with

AS/NZS3100 240 V AC, 4.5 kW/19 Amps, 50 Hz

Model

No:

ICBDF364C

Serial No:

Gas

type

LPG

Test point press. (kPa) 1.0 2.75

Injector sizes (mm)

RHF

RHR

Grill

LHF

LHR

1.80

1.78

1.80

1.35

1.09

0.89

Total Consumption (MJ/h) 66.0 66.1

MF028

Made in USA

GSCS20230

SAI GLOBAL

AS4551

Electrical compliance: in accordance with

AS/NZS3100 240 V AC, 4.5 kW/19 amps, 50 Hz

Model

No:

ICBDF364G

Serial No:

Gas

type

LPG

Test point press. (kPa) 1.0 2.75

Injector sizes (mm)

RHF

RHR

Griddle

LHF

LHR

1.80

1.70

1.80

1.35

1.09

0.89

Total Consumption (MJ/h) 66.0 66.1

MF018

Made in USA

GSCS20230

SAI GLOBAL

AS4551

Electrical compliance: in accordance with

AS/NZS3100 240 V AC, 8.4 kW/35 Amps, 50 Hz

Model

No:

ICBDF484CG

Serial No:

Gas

type

LPG

Test point press. (kPa) 1.0 2.75

Injector sizes (mm)

RHF

RHR

Grill

Griddle

LHF

LHR

1.80

1.78

1.70

1.80

1.35

1.09

0.89

Total Consumption (MJ/h) 81.0 81.1

MF016

Made in USA

GSCS20230

SAI GLOBAL

AS4551

Electrical compliance: in accordance with

AS/NZS3100 240 V AC, 8.4 kW/35 Amps, 50 Hz

Model

No:

ICBDF484F

Serial No:

Gas

type

LPG

Test point press. (kPa) 1.0 2.75

Injector sizes (mm)

RHF

RHR

French top

LHF

LHR

1.80

1.35

1.09

0.89

Total Consumption (MJ/h) 65.0 65.1

MF017

Made in USA

GSCS20230

SAI GLOBAL

AS4551

Electrical compliance: in accordance with

AS/NZS3100 240 V AC, 8.4 kW/35 Amps, 50 Hz

Model

No:

ICBDF486C

Serial No:

Gas

type

LPG

Test point press. (kPa) 1.0 2.75

Injector sizes (mm)

RHF

RHR

Grill

LHF/CF/CR

LHR

1.80

1.78

1.80

1.35

1.09

0.89

Total Consumption (MJ/h) 94.0 94.1

MF029

Made in USA

GSCS20230

SAI GLOBAL

AS4551

Electrical compliance: in accordance with

AS/NZS3100 240 V AC, 8.4 kW/35 Amps, 50 Hz

Model

No:

ICBDF486G

Serial No:

Gas

type

LPG

Test point press. (kPa) 1.0 2.75

Injector sizes (mm)

RHF/CF

RHR/CR

Griddle

LHF

LHR

1.80

1.70

1.80

1.35

1.09

0.89

Total Consumption (MJ/h) 94.0 94.1

MF030

Made in USA

GSCS20230

SAI GLOBAL

AS4551

Electrical compliance: in accordance with

AS/NZS3100 240 V AC, 9.1 kW/38 Amps, 50 Hz

Model

No:

ICBDF604CF

Serial No:

Gas

type

LPG

Test point press. (kPa) 1.0 2.75

Injector sizes (mm)

RHF

RHR

Grill

French top

LHF

LHR

1.80

1.78

1.80

1.35

1.09

0.89

Total Consumption (MJ/h) 80.0 81.1

MF026

Made in USA

GSCS20230

SAI GLOBAL

AS4551

Electrical compliance: in accordance with

AS/NZS3100 240 V AC, 9.1 kW/38 amps, 50 Hz

Model

No:

ICBDF606CG

Serial No:

Gas

type

LPG

Test point press. (kPa) 1.0 2.75

Injector sizes (mm)

RHF/CF

RHR/CR

Grill

Griddle

LHF

LHR

1.80

1.78

1.70

1.80

1.35

1.09

0.89

Total Consumption (MJ/h) 109.0 109.1

MF023

CO N TACT

IN F OR M ATIO N

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street

Melbourne Victoria 3000

Phone 03 9600 2218

subzero-wolf.com.au

W i r i n g d i a g r a m

MF 038

Sub-Zero Group Australia Pty Ltd

Level 10, 469 La Trobe Street

Melbourne Victoria 3000

Phone +61 3 9600 2218

subzero-wolf.com.au

Wolf ICBDF484F Installation Instructions Manual

Brand: Wolf

Model: ICBDF484F

Category: Ovens

Type: Installation Instructions Manual

This manual is also suitable for

Download PDF

report

Wolf ICBDF484F Installation Instructions Manual

This manual is also suitable for

Wolf ICBDF484F Installation Instructions Manual

Related papers

Other documents