Blueant CONNECT Bluetooth Earpiece User manual

CONNECT

USER GUIDE

Read Me to Get the Most Out of

Your Device...

• ENGLISH

• FRANÇAIS

• ESPAÑOL

TO GET STARTED

1. Turn The Connect On

2. Put It On

3. Listen In

Model: CT

Contents

Charge Your Earpiece 6

Wearing the Connect 7

Pair Your Earpiece 7

Use Your Voice to Control the Connect 8

Making Calls 10

Taking Calls 12

Volume Control 12

Changing the Ear Bud 13

Using 2 Phones (Multipoint) 14

Call Waiting and Conferencing* 14

Listening to Audio 16

Reset the Connect 17

Free Android Application 18

Reconnecting to the Earpiece 19

Button Commands 19

Help and Support 22

Terms and Conditions 22

Contact Us 24

5

Welcome to the BlueAnt Connect: the most brilliantly designed

ergonomic earpiece, featuring BlueAnt’s intuitive voice user

interface.

Designed for comfortable extended wear, the Connect also

comes with Siri and Google Voice Actions integration, rapid

charge technology to keep you connected, and high quality

true-to-life audio.

Volume

Rocker

Control

Command

Button

Microphones

Indicator Light

Charging

Port

6

Charge Your Earpiece

Your earpiece has been given an initial partial charge to get you

started, but for best results we recommend you fully charge it

using the supplied USB cable and adaptor.

> Charge the Connect whenever it announces that the battery

is Very Low. It will switch off automatically if the battery

runs out.

> Your earpiece features Rapid Charge technology. It will

charge to 50% capacity in just 30 minutes (a full charge takes

about 2 hours).

> During charging, the indicator light ﬂ ashes red.

> When the light goes white,

the charge is complete.

> The Connect features an

iPhone battery meter

so you can check

your battery

status at a glance.

Charging

Port

Hardware

Power Switch

7

Wearing the Connect

You can wear the Connect in either ear. For best results:

> Rotate the ear gel as shown here.

> Make sure that the earpiece is angled towards your mouth.

LEFT

EAR

RIGHT

EAR

Pair Your Earpiece

To use the Connect you need to pair it with your phone.

1. Slide the hardware power switch across to turn the Connect

on and then put the Connect in your ear.

2. If this is the ﬁ rst time you have used the Connect it will go

8

straight to pairing mode. The voice prompts will start to talk

you through the pairing process.

For subsequent pairings, click the Command button and

wait for the Connect to ask you to Say A Command. Then

say Pair Me.

3. Follow the voice prompts to pair the Connect with your

phone. If requested, the pairing code is 0000 (four zeros).

Note: If your phone prompts you to allow a connection to the

Connect, you must select “YES” or “OK”.

Use Your Voice to Control the Connect

Phone

Commands

3

Say A

Command

21

The Connect is voice controlled. Simply:

1. Click the Command button

9

2. Wait for the Connect to ask you to Say A Command

3. Say the command:

Command Description

Am I

Connected?

The Connect will check if your phone is

connected, and attempt to connect if not.

Call Back Calls back the last incoming call.

Check Battery Tells you the battery level on the Connect.

Pair Me Puts the Connect into pairing mode. Any

connected phone will be disconnected.

10

Command Description

Phone

Commands

Activates your phone’s voice dialing

feature (if supported). Depending on

your phone model, you may need to

record voice tags on the phone to use this

feature.

On the iPhone 4S this command activates

Siri.

On Android devices this command

activates Google Voice Actions.

Redial Redials the last outgoing call.

What Can I

Say?

Tells you the available voice commands.

Making Calls

Voice Dialing

Double click the Command button or use the Phone

Commands voice command to activate your phone’s voice

11

dialing feature (if available).

Once you have activated this feature, you are using your

phone’s voice recognition software. Please check your phone

manual to ﬁ nd out what commands your phone supports.

> On the iPhone 4S this feature activates Siri. There’s no need

to touch or unlock your iPhone. Note: Siri must be enabled

on your phone. Go to Settings > General on your iPhone and

check that Siri is set to ON. If you have set a passcode lock

you will need to set Siri to ON in the passcode lock menu.

> Android users: use this feature to access Google Voice

Actions (if available). Note: Depending on your handset, you

may need to disable the phone password lock to use voice

dialing over Bluetooth. Check your phone manual for further

information on this feature.

Other Ways To Make Calls

> Dial the number on your phone. The audio automatically

transfers to the earpiece.

> Use the Redial or Call Back commands.

12

Taking Calls

When the phone rings, wait for the prompt to ask you if you

want to take the call, and then say Answer or Ignore. Or:

> To accept the call click the Command button once.

> To reject the call double click the Command button.

During a call, click the Command button to end the call.

Volume Control

Use the volume rocker:

> Push up for volume up.

> Push down for volume down.

Note: See the next section for

advice if you wear the Connect in your left ear.

Wearing the Connect in your Left Ear?

The Connect volume controls are set by default for users

wearing the earpiece in their right ear.

Volume

Rocker

13

If you prefer to wear your earpiece in your left ear, follow these

simple steps to swap the volume orientation so that you can

still push up for volume up and down for volume down:

1. Put the Connect in your left ear.

2. Hold down the Command button, and push and hold the

volume rocker in the up position. Hold both buttons together

for about 3 seconds.

If you want to switch back, put the Connect back in your right

ear and repeat this procedure.

Note: If you reset your earpiece, it reverts to the default volume

control orientation (right ear).

Changing the Ear Bud

Your Connect is supplied with a choice of ear buds in different

sizes so that you can choose the one that ﬁ ts best. If you want

to change the ear bud, remove the attached one by gently

lifting it away from the Connect.

Gently press the replacement ear bud onto the Connect and

push it ﬁ rmly to secure it in place.

14

Using 2 Phones (Multipoint)

Up to 2 devices can connect to the earpiece at the same time. If

either phone rings, you can answer it with the earpiece.

Use the Pair Me command to put your Connect back into

pairing mode to pair another phone. Any currently connected

phone will be disconnected during pairing, so you will need to

reconnect afterwards.

Which Phone is Used for Calls?

When you have two phones connected you can always answer

an incoming call from either phone.

If you initiate a call through the earpiece (for example by saying

Phone Commands) then the call takes place on the primary

phone: the one that connected to the earpiece ﬁ rst.

Call Waiting and Conferencing*

If you receive an incoming call while you are already on a call

the Connect will play a tone to alert you.

15

To Do This

End the active call and

answer the incoming call

Click the Command button

Keep the active call, reject

the incoming call

Double click the Command

button

Put the active call on hold,

answer the incoming call

Hold the Command button

for about 1 second

Switch between the active

and held call

Hold the Command button

for about 1 second

Conference the active and

held call

Hold the Command button

for about 3 seconds

If you are using multipoint you can also use these controls to

switch between calls on both phones.

Note: You can only conference together calls received on the

same phone (although you can have conference calls running

on both phones at the same time).

* To use these features, your phone and network must support

call waiting and call conferencing.

16

Listening to Audio

The Connect supports A2DP audio streaming. If your phone

supports the A2DP proﬁ le then simply start playing music or

any other audio (including turn-by-turn directions from a GPS

application on your phone) and it will automatically transfer to

the earpiece.

If the phone rings the audio will mute. You can use your voice

to answer or ignore the call. Or:

> Click the Command button to accept the call.

> Double click the Command button to ignore the call.

The audio will resume when the call ends.

If you want to exit A2DP streaming mode to do something else:

> Click the Command button to activate the Connect’s voice

control feature. If you do not say one of the Connect’s voice

commands within a few seconds the music will resume

playing; or

> Double click the Command button to activate your phone’s

voice dialing feature (if available).

17

Reset the Connect

If you are having problems with the Connect, you can reset it

and start again.

Resetting the Connect will clear all the stored pairing settings,

reset the volume orientation to the default and put the device

back into pairing mode.

To reset the Connect:

1. Delete any existing pairing information from your phone

and turn the phone off and back on again to clear the phone

memory.

2. Make sure the Connect is switched on but not connected to

any phones.

3. Hold down the Command button and Vol + together for

about 5 seconds.

4. The Connect will announce that it has been reset.

5. Now use the hardware switch to turn the Connect off and

back on again.

You will now need to pair your phone with the Connect again.

18

Free Android Application

> Reads your incoming text messages

> Helps with pairing and setup

Go to the Android Market and search for “BlueAnt” to

download and install this free application. Once the application

is installed you will hear your text messages read aloud

automatically on your BlueAnt device as they come in.

Supports Android handsets running Android version 2.1 or

above.

Android is a trademark of Google, Inc, and its use is subject to

its permissions.

Scan this code on your

phone with a QR code

reader to download the

application:

19

Reconnecting to the Earpiece

If you take your phone out of range of the earpiece for more

than 2 minutes, the Connect will go into “sleep mode” to save

battery. When you bring your phone back into range, simply

double click the Command button to reconnect.

Alternatively, use the hardware switch to turn the Connect off

whenever you are not using it. The Connect will automatically

attempt to reconnect to your phone when you switch it on.

Depending on your phone, this may take a few seconds. Please

ensure that Bluetooth is enabled on your phone.

Button Commands

Function Do This When

Activate voice

dialing, Siri or

Google Voice

Actions (if

available) on the

primary phone

Double click the

Command button

Phone

connected but

not on a call

20

Function Do This When

Answer a call Click the Command

button

Phone ringing

End a call Click the Command

button

During an active

call

End the active call

and answer an

incoming call

Click the Command

button

Phone ringing

during an active

call

Reject a call Double click the

Command button

Phone ringing

Keep the active

call and reject the

incoming call

Double click the

Command button

Phone ringing

during an active

call

Hold active call

and switch to

incoming or held

call

Hold the Command

button for about 1

second

During an active

call (with phone

ringing or call

on hold)

Page is loading ...

Blueant CONNECT Bluetooth Earpiece, Connect User manual

Related papers

Other documents