SportsArt Fitness C572U Owner's manual

Type
Owner's manual

This manual is also suitable for

TABLE OF CONTENTS
CARDIO ACTIVE ENTERTAINMENT STATION (INTEGRATED TV)
FOR THE C572R RECUMBENT CYCLE
CARDIO ACTIVE ENTERTAINMENT STATION (INTEGRATED TV)
FOR THE C572U UPRIGHT BIKE
CARDIO ACTIVE ENTERTAINMENT STATION (INTEGRATED
ANALOG TV) OPERATING MANUAL
CHAPTER 1:
CHAPTER 2:
CHAPTER 3:
1.1 INSTALLATION MANUAL..................................................................................
1.2 INSTALLATION INSTRUCTIONS.......................................................................
STEP 1 Remove the Front Lower Cover.........................................................
STEP 2 Disconnect Cables and Remove the Pedestal...................................
STEP 3 Remove the Left Pedal and Crank Cover...........................................
STEP 4 Install Cables......................................................................................
STEP 5 Organize Cables.................................................................................
STEP 6 Install the Left Side Cover and Pedal.................................................
STEP 7 Secure the Pedestal...........................................................................
STEP 8 Remove the Cutaway.........................................................................
STEP 9 Install the Integrated TV Module........................................................
STEP 10 Install the Adaptor Box.......................................................................
STEP 11 TV Angle Adjustment..........................................................................
2.1 INSTALLATION MANUAL..................................................................................
2.2 INSTALLATION INSTRUCTIONS.......................................................................
STEP 1 Remove the Pedestal and Front Lower Cover......................................
STEP 2 Disconnect Cables and Remove the Pedestal......................................
STEP 3 Install Cables.........................................................................................
STEP 4 Install the Seat Bottom and Pedals.......................................................
STEP 5 Remove the Cutaway............................................................................
STEP 6 Install the TV Module...........................................................................
STEP 7 Install the Adaptor Box.........................................................................
STEP 8 TV Angle Adjustment............................................................................
3.1 TV Operating Instructions...................................................................................
3.2 CATV Function Settings......................................................................................
1
2
4
6
7
8
9
10
11
12
13
16
17
18
19
21
23
24
25
26
27
30
31
33
34
3.3 OSD Menu and Keys in CATV Mode...................................................................
3.4 How to Perform the Search Function..................................................................
3.4.1 Search Function Illustrations - TV System........................................................
3.4.2 NTSC Cable Illustration.....................................................................................
3.4.3 TV Scan............................................................................................................
3.4.4 TV Channel Search in Progress.......................................................................
3.4.5 iPod Function....................................................................................................
3.5.1 iPod Function Illustrations – iPod System........................................................
3.5.2 iPod Function Illustrations – iPod On...............................................................
3.5.3 iPod Function Illustrations – Source Key..........................................................
3.6.1 OSD Menu, Other Functions - Video................................................................
3.6.2 OSD Menu, Other Functions - Audio................................................................
3.6.3 OSD Menu, Other Functions - System.............................................................
3.6.4 OSD Menu, Other Functions - DTV..................................................................
4.1 Digital TV System Cable Connections.................................................................
4.2 Integrated TV Screen Illustration.........................................................................
4.3 DTV ATSC-USA Digital TV Functions............................................................
4.4 DTV Mode Operation...........................................................................................
4.4.1 DTV Mode.........................................................................................................
4.4.2 ATSC Menu.......................................................................................................
4.4.3 DTV Mode Key Definitions................................................................................
4.5 Introduction to the ATSC Menu............................................................................
4.6 Auto Search Operation.........................................................................................
4.6.1 DTV Menu.........................................................................................................
4.6.2 Scan Window....................................................................................................
4.6.3 Channel Search Completed Window................................................................
4.6.4 Channel Scan...................................................................................................
4.7 DTV DVB-T (European) Digital TV Functions................................................
4.8 The System Setup Process.................................................................................
4.8.1 Country Setting.................................................................................................
4.8.2 Channel Search................................................................................................
4.8.3 Channel Search Block Diagram........................................................................
CHAPTER 4: CARDIO ACTIVE ENTERTAINMENT STATION – INTEGRATED
DIGITAL TV
()
()
34
37
37
38
38
39
39
40
40
41
42
43
43
45
47
47
48
50
50
50
50
51
51
51
52
52
54
55
56
56
60
60
4.9 Other Notes.........................................................................................................
4.9.1 DVB-T Menu.....................................................................................................
4.9.2 Program Search................................................................................................
4.9.3 Parental Control................................................................................................
4.9.4 System Settings................................................................................................
4.9.5 Games..............................................................................................................
4.9.6 Accessories......................................................................................................
4.9.7 Personal Style..................................................................................................
4.10 Setup Menu Navigation.....................................................................................
4.11 DVB T Frequency Table and Country List..........................................................-
63
63
64
64
64
65
65
66
67
68
1
Install the CardioActive™ Entertainment Station (integrated TV) onto the SportsArt
C572R cycle as follows.
L
R
CHAPTER 1CARDIO ACTIVE ENTERTAINMENT STATION
(INTEGRATED TV) FOR THE C572R RECUMBENT BIKE
1.1 INSTALLATION MANUAL
No. Qty
No.
Qty
A1
A2
A3
A4
1
1
1
5
1
A6
A7
A8
A9
A10
2
1
1
1
1
1
1
Parts in the Main Module Assembly
Integrated TV module
Owner's manual
TV lower power cord
TV adaptor
Power switch
F connector adapter
A5
Coaxial cable splitter
Ground wire
Lower cable
Zip tie
Part Name Part Name
Power cord
1.2 INSTALLATION INSTRUCTIONS
STEP 1 Remove the Front Lower Cover
4
3
No. Name Qty
21
Parts in the Hardware Kit
4
4
4
1
1
1
1
2
1
Specification
Notes
Inner hex screw
Spring washer
Serrated washer
Screwdriver bit and handle
L-shaped Allen wrench
L-shaped Allen wrench
M11 open-end wrench
Double open-end wrench
L-shaped Allen wrench
M6*L15
M6
D20*d6.2*t2.0*19t
Straight and Phillips heads
M5
M6
M4
12*15
The CardioActive™ Entertainment Station is an integrated TV module for use on
several SportsArt Fitness products. Please follow instructions below to install this
integrated TV module on the C572R cycle.
Note: For brevity, throughout this manual, the word “screws” is used where screws,
washers, and other hardware may be involved. Also, the words “left” and “right” are
used in reference to the product and its parts. Note that as such, these designations
correspond to the left and right sides of a person in position to work out on the
product. Also note that some parts are marked “L” for left or “R” for right.
5
(a) Remove the front lower cover as indicated by (A) and (B) below.
Remove screws separately from the power terminal plate and the AV terminal
plate.
First, loosen the nut on the . From the front, secure the AV
terminal plate. Then install the power switch (A5) into the power switch bracket.
On the other side, first loosen the nut. Then, inserting it from the front, secure the
cable connector as shown.
(b)
(c) F connector adapter (A5)
(b)
(a)
(c)
A
B
STEP 2 Disconnect Cables and Remove the Pedestal
(
(c)
a) Remove screws from the display cover.
(b) Disconnect cables in three places, A, B, and C. In area D, remove the two cables;
these cables will not be needed.
Remove the caps that cover screw heads on the pedestal. Then remove the
screws from the pedestal.
(d) Lift the pedestal, and disconnect the data cable.
6
(d)
(c)
(b)
(a)
A
B
C
D
STEP 3 Remove the Left Pedal and Crank Cover
(a) Remove the left pedal.
(b) Remove the crank cover.
c) Remove screws from the left side cover.
(d) Rotate the crank 180 degrees until it points upward vertically as shown.
(e) Lift the left side cover off, tilting it to avoid the crank and the product frame.
(
7
(e)
(d)
(c)
(b)
(a)
STEP 4 Install Cables
(a) From the hole in the display cover, thread the TV lower power cable (A3) and
lower cable (A8) into the pedestal. Then thread the cables through the unit, and
out the hole at the left side as shown.
(b) Lift the pedestal. Tuck cables safely into the pedestal and its base, making sure
that cables will not get pinched. Then insert the pedestal into its base, and secure
the pedestal screws.
8
(b)
(a)
STEP 5 Organize Cables
(a) After connecting cable (A3), cable (A8), the power switch, and the
, secure the power switch bracket onto the unit as shown.
(b) Starting at the power switch bracket side, organize cables. Use zip ties (A9) to
secure the cables to the frame as shown.
F connector
adapter (A5)
9
(b)
(a)
STEP 6 Install the Left Side Cover and Pedal
(a) Hold the crank up while slipping the left side cover into place.
(b) Turn the crank 180 degrees, so it hangs downward.
(c) Secure left side cover screws.
(d) Put the crank cover back into place.
(e) Secure the left pedal back into place.
10
(e)
(d)
(c)
(b)
(a)
STEP 7 Secure the Pedestal
(a) Secure the pedestal screws and their caps.
(b) Put the front lower cover into place, following sequence (A), then (B).
11
(b)
(a)
A
B
STEP 8 Remove the Cutaway
Remove the cutaway to allow for installation of the TV module.
(a) Remove the sticker from the top of the fan cover.
(b) Use a pair of wire cutters to remove the cutaway in area A.
12
(b)
(a)
A
A
STEP 9 Install the Integrated TV Module
Follow steps (a) through (f) to install the TV module.
(a) Before installing the integrated TV module (A1), carefully cut the zip tie off the coil
of cables. From above the cutaway area, align the integrated TV module (A1)
with the guide tube. While sliding the integrated TV module into place, feed the
cables through holes in both sides of the display covers. Two cables go into the
hole in the right side; Other cables go through the hole in the left side.
(b) Put a screw (21) through the end of the ground wire (A7) and secure all screws,
first in area A, then in area B. Note: Place the serrated washer lowest when
securing the ground wire.
13
(b)
(a)
L
R
A
B
(c) Secure the coaxial cable splitter (A6) onto the display lower cover. Then
connect integrated TV module (A1) CATV(1) and DTV(2) cables and the lower
coaxial cable (A3) to the splitter (A6). Then secure the ground wire (A7) from the
center of the wires marked (L2) onto the coaxial cable splitter ground wire
connection.
S
14
(c)
15
(e)
(d)
(f)
B
C
A
b
a
(d) Connect the integrated TV cable (L1) to the similarly marked TV lower power cable
(A3).
(e) Connect the integrated TV module cable (L2) to the board for iPod. Connect cable
(L3) to the display board. (Note: There are two types of boards for iPod. One
supports audio-video functions. The other one only supports audio functions. If you
intend to use video, you must use a board with audio-video functions. To use an
audio-only board for iPod, you need not connect cable (L2). If no board for iPod is
to be used, do not connect cable (L2). Leave it disconnected but secured in the
display area.
(f) After connecting cables, secure the display cover.
Audio-only board for iPod
Audio-video board for iPod
STEP 10 Install the Adaptor Box
Route the adaptor cord under the front of the cycle, insert it into the adaptor (A4), and
insert the main power cord from the adaptor box into the power outlet, and insert it
into the power cord (A9)
16
STEP 11 TV Angle Adjustment
To secure the angle of the TV screen at its recommended position, follow instructions
on the sticker (inside the neck cover). To secure the TV screen angle at a different
position, follow steps (a) through (d) below.
(a) Remove the integrated TV module neck cover.
(b) Remove the screws at the lower left and right sides of the bracket (area B).
Loosen (but do not remove) screws in position (A) until the angle of the TV screen
can be adjusted.
After adjusting the angle of the integrated TV screen, secure screws in area (A).
While aligning screw holes, secure screws from step (b).
(c)
(c)
(d)
(b)
(a)
A
A
C
B
B
17
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71

SportsArt Fitness C572U Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI