Bellaterra Home 804375A-36-BL Installation guide

Brand: Bellaterra Home

Model: 804375A-36-BL

Type: Installation guide

- 1 -

Roughing -in Dimensions

*Dimensions shown for location of supplies and “p” trap are suggested.

Adjustable wrench

Saber Saw

Basin Wrench

Plumbers putty or

Caulking

Channel Loks

Pipe Wrench

Putty Knife

Tape

Measure

Tubing Cutter

Drill

Hacksaw

Level

Phillips Scrtewdriver

Regular Screwdriver

TooIs and materiaIs Required

Most of the procedures require

the use of avaiIabing,supply stores.

It is essential that the tooIs and

materials be on hand before work

is begun.

ASSEMBLY & INSTALLATION

INSTRUCTIONS

804375A-BL-36

INTRODUCTION

Thank you For selecting our BELLATERRA HOME product.To ensure that your installation proceeds smoothly,

read these instructions carefully before you begin.Also,review the recommended tools and

materials section.Carefully unpack and examine your new plumbing fixture.

ALL INSTALLATION PROCEDURES MUST COMPLY IN STRICT ACCORDANCE WITH

APPLICABLE LOCAL LOCAL PLUMBING AND BUILDING CODES

74 3/4"

(1900m m )

82"

(2100m m )

31 1/2"

(800mm)

34 1/16"

(865mm)

35 13/1 6 "

(910m m )

- 2 -

Co de

QT Y

Co mp one nt

E F

Accessory

list

2 3

Expended

partides

He xa g on

sc re w

I J

Na me

Be ac k et

Step On e:Use the t rack level b ar, tape measu re an d pencil to ma rk holes in de sir ed locatio n.H aving esta bli shed

the pos ition,us e dri ll to make hol es. Use the hamm er to i nsert anch ors into the h ole a nd screw in th e scr ews.

Final ly put the mir ror i n place.

Step Tw o:Place t he vanity in p osi tion.Lev el va nity ensur ing i t is level wit h water outl ets a nd piping. If th e

doors a re out of alig nme nt they can be f ixe d by adjusti ng th e hinges.

Step Th ree:Fix the v anity to the w all t hrough the b ack r ail of the cab inet (for wa ll hu ng units). The f ixings sho uld

be plac ed on a wall stu d.W erecomme nd th at you use a tog gle or toggl e typ e system if yo u can 't located a s tro ng

solid s urface.

Step Fo ur: (For un dermount s ink u nit) Glue th e und ermount si nk to t he Stone Top i n suitable p lac e, put them on t he

cabin et after the g lue i s dry. Make su re th e sink and sto ne st ick to each ot her strong e nou gh.

(For se mi re cesse d bas in unit) Put t he ba sin on the cab ine t in suitabl e place. Glu e the b asin to the

cabin et if necess ary .

(For ab ove c ounte r bas in unit) Put t he st one top on the c abi net and plac e the basin on s ton e in suitabl e

place .

Step Fi ve: (If has b oard shelf ) Use t he track lev el ba r,tape mea sur e and pencil t o mark holes i n des ired

locat ion.Havi ng es tablishe d the p osition, use drill to make holes. Use t he hammer to i nse rt anchors i nto the hole a nd

screw i n the screws .Fi nally put th e boa rd shelf in pl ace .

Connect the trap to the drain assembly hand tight to check

alignment. It may be necessary to cut off part of the tailpiece

(area"A") or part horizontal leg of the trap (area "B").

Trap joints for watertight assembly.

Coect hot and cold supply lines to the shut off valves. Tighten

Typical Drain Assembly

Install faucet and drain in accordance with

manufacturer’s instructions.Ensure all water supply

and drain connections are tightened. Turn on water

supply valves and water-test installation.

- 3 -

Plactic Adjuster Install

Install

- 4 -

INSTALLATTON TIPS:

BLUM TIP-ON FOR TANDEM

Depth Adjustment

Bellaterra Home 804375A-36-BL Installation guide

Bellaterra Home 804375A-36-BL Installation guide

Bellaterra Home 804375A-36-BL Installation guide

Related papers

Other documents