American Pro Decor assumes no liability for improper installation.
INSTALLATION MANUAL
TOOLS REQUIRED
INCLUDED IN KIT
• Plumb Line
• Pencil
• Phillips Head Screwdriver
• 4mm Drill Bit
• Wrench
• Level
• Power Drill
• Tape Measure
F
U
RN
I
T
U
RE
F
U
RN
I
T
U
RE
PLEASE NOTE: The installation manual is a suggested guideline. Adjustments may need to be made based on your specic application.
A
Door Roller Hardware x2
B
Anti-Jump Disk x2
C
Door Stop Hardware x2
D
End Cap x2
E
Mounting Bracket for ¾" and 1" Doors x5 ea.
F
M6x60 Bolt + Washer x10
G
Routed Door Guide x1
H
ST4.2x35 Screw x2
I
Anchor x2
J
1.5mm Allen Key x1
K
Hole Cover x4
L
72" Rail x1
A
B C D
E F
G H
K
L
I
J
6 FT. KIT for SINGLE DOOR
American Pro Decor assumes no liability for improper installation.
16” 4”
16”
72”
16” 16”4”
1
Using a pencil, mark the locations where you will drill holes
as indicated.
Using a power drill with a 4mm drill bit, drill holes as indicated.
UNDERSTANDING YOUR RAIL
INSTALLATION
American Pro Decor assumes no liability for improper installation.
2
Mounting Bracket [E]
Door Stop [C]
Furniture Rail
[L]
M6x60 Bolt
[F]
Mounting
Bracket
[E]
Door Stop
[C]
3
5"
Mounting Screws
Install the rail, mounting brackets [E], and door stops [C].
NOTE: Door stops [C] are installed on the outermost holes of
the rail and shares the same mounting hardware [E].
Drill holes into the doors as indicated. Attach the roller straps [A].
It is suggested that the roller strap [A] be mounted 5" from the edge of the door
to the neck of the roller strap.
NOTE: Trimming the rail will alter the position of the roller hardware.
Adjust accordingly.
American Pro Decor assumes no liability for improper installation.
3⅛"
3⅛"
FOR ¾" DOORS
FOR 1" DOORS
Allow a minimum 3-1/8" clearance above the doors.
5
American Pro Decor assumes no liability for improper installation.
Attach the anti-jump disks [B] to the doors.
Attach the doors to the rail [L] and lock the anti-jump disks [B] into position. Doors should be routed beforehand
if using the routed door guide [G].
4
5
Roller Strap [A]
Anti-Jump Disk [B]
Anti-Jump Disk [B]
(x2)
(x2)
6
American Pro Decor assumes no liability for improper installation.
If using the routed door guide [G], install at this time. Use the hole covers [K] to give the rail a
nished look.
Once cut, add the end caps [D] to the ends of the rail and secure with a
set screw.
NOTE: If you are trimming the rail, do so equally. Each
rail can be trimmed equally up to 3" on both sides.
However; trimming will alter the position of the roller
hardware. Adjust accordingly.
6
7
Routed Door Guide [G]
Hole Covers [K]
The rail can be trimmed if necessary using a band saw.
Use blades suitable for iron or stainless steel depending
on your rail.
8
End Cap [D]
End Cap [D]
3" Max
3" Max
-
1
-
2
-
3
-
4
-
5
-
6
American Pro Decor 5APD10789 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Pro Decor 5APD10901 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
ROOMS TO GO 33023196 Assembly Instructions
-
-
DreamLine SHEN-6134600-07 Installation guide
-
-
-
-
-
-
FURNITURE FSDH-STPKT-5-DD Installation guide
-
FURNITURE FSDH-TOPKT-4-DD Installation guide