American Pro Decor 5APD10786 Installation guide

American Pro Decor
Brand
American Pro Decor
Model
5APD10786
Type
Installation guide

This manual is also suitable for

American Pro Decor 5APD10786 is a furniture installation kit designed to install single doors on cabinets or other furniture pieces. It includes all the necessary hardware, such as door roller hardware, anti-jump disks, door stop hardware, end caps, mounting brackets, bolts, screws, anchors, and a routed door guide.

This kit is suitable for both 3/4" and 1" thick doors and can be used to install doors up to 72" wide. The rail can be trimmed up to 3" on both sides to accommodate narrower openings. The included routed door guide ensures a smooth and quiet operation of the doors. The anti-jump disks prevent the doors from jumping off the rail, while the door stop hardware limits the travel of the doors.

American Pro Decor 5APD10786 is a furniture installation kit designed to install single doors on cabinets or other furniture pieces. It includes all the necessary hardware, such as door roller hardware, anti-jump disks, door stop hardware, end caps, mounting brackets, bolts, screws, anchors, and a routed door guide.

This kit is suitable for both 3/4" and 1" thick doors and can be used to install doors up to 72" wide. The rail can be trimmed up to 3" on both sides to accommodate narrower openings. The included routed door guide ensures a smooth and quiet operation of the doors. The anti-jump disks prevent the doors from jumping off the rail, while the door stop hardware limits the travel of the doors.

American Pro Decor assumes no liability for improper installation.
INSTALLATION MANUAL
TOOLS REQUIRED
INCLUDED IN KIT
• Plumb Line
• Pencil
• Phillips Head Screwdriver
• 4mm Drill Bit
• Wrench
• Level
• Power Drill
• Tape Measure
F
U
RN
I
T
U
RE
F
U
RN
I
T
U
RE
PLEASE NOTE: The installation manual is a suggested guideline. Adjustments may need to be made based on your specic application.
A
Door Roller Hardware x2
B
Anti-Jump Disk x2
C
Door Stop Hardware x2
D
End Cap x2
E
Mounting Bracket for ¾" and 1" Doors x5 ea.
F
M6x60 Bolt + Washer x10
G
Routed Door Guide x1
H
ST4.2x35 Screw x2
I
Anchor x2
J
1.5mm Allen Key x1
K
Hole Cover x4
L
72" Rail x1
A
B C D
E F
G H
K
L
I
J
6 FT. KIT for SINGLE DOOR
American Pro Decor assumes no liability for improper installation.
16” 4”
16”
72”
16” 16”4”
1
Using a pencil, mark the locations where you will drill holes
as indicated.
Using a power drill with a 4mm drill bit, drill holes as indicated.
UNDERSTANDING YOUR RAIL
INSTALLATION
American Pro Decor assumes no liability for improper installation.
2
Mounting Bracket [E]
Door Stop [C]
Furniture Rail
[L]
M6x60 Bolt
[F]
Mounting
Bracket
[E]
Door Stop
[C]
3
5"
Mounting Screws
Install the rail, mounting brackets [E], and door stops [C].
NOTE: Door stops [C] are installed on the outermost holes of
the rail and shares the same mounting hardware [E].
Drill holes into the doors as indicated. Attach the roller straps [A].
It is suggested that the roller strap [A] be mounted 5" from the edge of the door
to the neck of the roller strap.
NOTE: Trimming the rail will alter the position of the roller hardware.
Adjust accordingly.
American Pro Decor assumes no liability for improper installation.
3⅛"
3⅛"
FOR ¾" DOORS
FOR 1" DOORS
Allow a minimum 3-1/8" clearance above the doors.
5
American Pro Decor assumes no liability for improper installation.
Attach the anti-jump disks [B] to the doors.
Attach the doors to the rail [L] and lock the anti-jump disks [B] into position. Doors should be routed beforehand
if using the routed door guide [G].
4
5
Roller Strap [A]
Anti-Jump Disk [B]
Anti-Jump Disk [B]
(x2)
(x2)
6
American Pro Decor assumes no liability for improper installation.
If using the routed door guide [G], install at this time. Use the hole covers [K] to give the rail a
nished look.
Once cut, add the end caps [D] to the ends of the rail and secure with a
set screw.
NOTE: If you are trimming the rail, do so equally. Each
rail can be trimmed equally up to 3" on both sides.
However; trimming will alter the position of the roller
hardware. Adjust accordingly.
6
7
Routed Door Guide [G]
Hole Covers [K]
The rail can be trimmed if necessary using a band saw.
Use blades suitable for iron or stainless steel depending
on your rail.
8
End Cap [D]
End Cap [D]
3" Max
3" Max
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

American Pro Decor 5APD10786 Installation guide

American Pro Decor
Brand
American Pro Decor
Model
5APD10786
Type
Installation guide
This manual is also suitable for

American Pro Decor 5APD10786 is a furniture installation kit designed to install single doors on cabinets or other furniture pieces. It includes all the necessary hardware, such as door roller hardware, anti-jump disks, door stop hardware, end caps, mounting brackets, bolts, screws, anchors, and a routed door guide.

This kit is suitable for both 3/4" and 1" thick doors and can be used to install doors up to 72" wide. The rail can be trimmed up to 3" on both sides to accommodate narrower openings. The included routed door guide ensures a smooth and quiet operation of the doors. The anti-jump disks prevent the doors from jumping off the rail, while the door stop hardware limits the travel of the doors.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents