2. Danfoss
  3. TP4000 Range
TP4000 Range

Danfoss TP4000 Range Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Danfoss TP4000 Range Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
TP4000 Range
Electronic programmable room thermostat
Danfoss Heating
MAKING MODERN LIVING POSSIBLE
Installation Guide
TP4000
2
For a large print version of these instructions
please call Marketing on 0845 121 7400.
Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other
printed material. All trademarks in this material are property of the respective companies.
Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
Danfoss Heating
3
FR
ES
NL
GR
PL
CZ
TR
GB
1.0 Product Specifi cation ...................................4
2.0 Installation ....................................................5
2.1 Thermostat Wiring (Hard wired model only) ......................5
2.2 RX Receiver Wiring (RF models only) ....................................6
3.0 Commissioning (RF models only) ...............6
4.0 TP4000/TP4000 RF Programming...............7
Index
TP4000 Range
Electronic programmable room thermostat
TP4000
4
FR
ES
NL
GR
PL
CZ
TR
GB
1.0 Product Specifi cation
Please Note:
This product should only be installed by a qualifi ed
electrician or competent heating installer and should
be in accordance with the current edition of the IEEE
wiring regulations.
Thermostat features TP4000 TP4000 RF
Power supply 2 x AA/MN1500/LR
alkaline cells
2 x AA/MN1500/LR
alkaline cells
Memory back-up 1 min for battery change
Switching action of
output relay
1 x SPDT, Type 1B N/A
Switch rating of relay
contact
3(1)A, 10-230Vac N/A
Transmission frequency
(RF Models)
433.92MHz
Transmission range 30m max
Temperature range Off , 5-30°C
Dimensions, mm 110 wide, 88 high, 28 deep
Design standard EN60730-2-9 EN300220
Rated impulse voltage 2.5kV
Ball hardness test 75°C
Control pollution
situation
Degree 2
Temperature accuracy ±1°C
Time accuracy ±1 min. per month
Important note RF products: Ensure that there are no large metal
objects, such as boiler cases or other large appliances, in line of
sight between the transmitter and receiver as these will prevent
communication between thermostat and receiver.
Danfoss Heating
5
FR
ES
NL
GR
PL
CZ
TR
GB
2.0 Installation
· First, remove the wallplate from the back of the unit.
· From the top left hand corner of the wallplate, there must be
clearances of at least 150mm to the right, 15mm to the left,
30mm above and 100mm below in order to mount the plug-in
module.
· Fix at a height of approximately 1.5m from the fl oor, away from
draughts or heat sources such as radiators, open fi res or direct
sunlight.
2.1 Thermostat Wiring (Hard wired model only)
1
OFF
23
COM ON
N/C
N/O
!
Some existing thermostats will have a Neutral and/or Earth wire connected.
These are not required by the TP4000 and must NOT be connected to any TP4000
terminals. Instead they should be made electrically safe and coiled in the recess
at the back of the TP4000.
TP4000
6
FR
ES
NL
GR
PL
CZ
TR
GB
3.0 Commissioning (RF models only)
If the thermostat and the receiver have been supplied together
in a combined pack, the units have been paired in the factory
and no commissioning is required (RX1 only).
To make the RX receiver learn the thermostat’s signal, follow steps 1-5
below.
Step 1
TP4000-RF - Reset the unit by pressing the recessed reset button.
Step 2
Press and hold V and + buttons for 3 seconds
(TP4000 RF now transmits unique signal
continuously for 3 minutes).
RX1
RX2 & RX3
12
3
4
ELECTRONICS
N
L
COM
ZONE
1 ON
ZONE
1 OFF
A
ELECTRONICS
B
C1
2
345
6
N
L
ZONE
1 ON
ZONE
1 OFF
ZONE
2 ON
ZONE
3 ON
COM
TERMINAL 6
RX3 ONLY
2.2 RX Receiver Wiring (RF models only)
1) For mains voltage operated systems link terminal 2 to mains live supply.
2) Power supply to unit must not be switched by timeswitch.
IMPORTANT
On initial installation, or if the batteries have been removed
from the unit for more than 1 minute before beginning
programming or commissioning the TP4000 unit; it is essential
that the RESET button be pressed to ensure the factory preset
programmes are set and the system is fully operational.
Danfoss Heating
7
FR
ES
NL
GR
PL
CZ
TR
GB
Step 3
RX1 - Press and hold buttons PROG and
CH1 for 3 seconds until green light fl ashes
once.
Step 4
RX2 (if applicable)
Stat 1 - perform steps 1-3 and 5.
Stat 2 -perform steps 1-2 and then press
PROG and CH2 on RX2.
RX3 (if applicable)
Stat 1 - perform steps 1-3 and 5.
Stat 2 - perform steps 1-2 and then press
PROG and CH2 on RX3 then step 5.
Stat 3 - perform steps 1-2 and then press
PROG and CH3 on RX3.
Step 5
TP4000-RF - Press V or Λ to select
temperature - the unit will revert back to
operating mode.
4.0 TP4000/TP4000 RF Programming
For details of this function, please refer to the user instructions.
Danfoss Heating
43
Danfoss Randall Ltd.
Ampthill Road
Bedford MK42 9ER
Tel: 0845 1217 400
Fax: 0845 1217 515
Email: danfossrandall@danfoss.com
Website: www.danfoss-randall.co.uk
Part No. 40811V01 03/09
/