2. Toto
  3. TET2GAR-SS
TET2GAR-SS

Toto TET2GAR-SS, TET2GA31-SS, TET2GA33-SS Dimensions Guide

  • Hello! I am an AI chatbot trained to assist you with the Toto TET2GAR-SS Dimensions Guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
TET2GA
ECOPOWER
®
Toilet Flush Valve, 1.6 GPF
FEATURES
• 1.6 GPF
• Self-powered hydroelectric flush valve system
• No minimum daily usage requirement
• Heavy-duty 14" x 12" stainless steel coverplate with
satin finish and solid bronze valve body
• Self-cleaning piston valve with 360° filter screen
• Neutral rough-in and adjustable tail piece connection
• Manual flush override
• Smart sensor with self-adjusting detection range
• 6-second detection time to prevent ghost flushing
• Concealed flush valve with 1" angle stop and
1-1/2" vacuum breaker set
• ADA compliant
COLORS/FINISHES
MODELS
CODES/STANDARDS
PRODUCT SPECIFICATION
• #SS Stainless Steel
TET2GA31#SS (Back spud wall)
• TET2GAR#SS (1.6 GPF flush valve)
• VB1331#RB (1-1/2" vacuum breaker tube,
1" angle stop)
TET2GA32#SS (Top Spud)
• TET2GAR#SS (1.6 GPF flush valve)
• VB1332#RB (1-1/2" vacuum breaker tube,
1" angle stop)
TET2GA33#SS (Back spud floor)
• TET2GAR#SS (1.6 GPF flush valve)
• VB1333#RB (1-1/2" vacuum breaker tube,
1" angle stop)
• Meets or exceeds ASSE 1037, CSA B125.3
• Certifications: IAPMO(cUPC), ASSE, State of
Massachusetts, and others
• Code Compliance: UPC, IPC, NSPC, NPC Canada,
and others
• ADA compliant
• Complies with CA Prop 65 warning requirements
TOTO
®
Model No. _____________________________
Product shall be 1.6 GPF. Product shall be an
automatic infrared sensor-activated, toilet flush valve.
Product shall use hydropower, ECOPOWER flush
valve system. Product shall have heavy-duty 14" x 12"
stainless steel coverplate with satin finish and solid
bronze valve body. Product shall have smart sensor
with self-adjusting detection range. Product shall have
neutral rough-in and adjustable tail piece connection
Product shall have smart sensor with self-adjusting
detection range. Product shall have manual flush
override. Product shall have 6-second detection time
to prevent ghost flushing. Product shall have piston
with debris screen and solenoid with self-cleaning
mechanism. Product shall be ADA compliant.
ECOPOWER
OPTIONAL ACCESSORIES
• Z-4000-J - Adapter for ground joint angle stops
Piston Valve
Auto Flush
TET2GA
ECOPOWER
®
Toilet Flush Valve, 1.6 GPF
#SS-01165, v.02
Ph: (888) 295-8134 | Fax: (800) 699-4889 | www.totousa.com | © TOTO USA
These dimensions and specifications are subject to change without notice
SPECIFICATIONS
*Water pressures over 80 psi are not recommended for most plumbing
fixtures. Check your local plumbing code for details.
INSTALLATION NOTES
• Material Bronze casting
• Power supply ECOPOWER
• Sensor detection time Factory setting at six
(6) seconds minimum
• Sensor detection range Self-adjusting to
environment
• Discharge quantity Preset to 1.6 GPF/
6.0 LPF
• Operating temperature 32°-104°F (0°-40°C)
• Water supply pressure 15 psi - 125 psi*
• Water supply connection 1" NPT
• Warranty Three year limited
For commercial applications only.
Warning: Failure to properly adjust angle stop to
the appropriate level can potentially cause property
damage.
For detailed installation instructions, please refer to
the installation manual.
Max flow rate to be used with
TET2GA___________: 1.6 GPF
Confirm with local codes and standards for floor drain
requirement. Adjust control stop for proper flow rate
to the fixture.
The recommended installation for the flush valve is
to have a 7" (178mm) minimum space in wall. Do not
place grab bars in front of sensor for ADA stalls.
DIAGRAM
Left water supply
1” NPT (toilet), 3/4” (urinal)
4-3/4” ± 1/2”
(120 ± 13mm)
Sensor Location
3-7/16” (87mm)
** 11-15/16”
(303mm)
16” (406mm)
3/4” (19mm)
Stud
Toilet top spud
Ø2-3/16” (Ø56mm) hole
Urinal Back spud
Ø1-5/16” (Ø33mm) hole
Toilet Back spud
Ø2-3/16” (Ø56mm) hole
11” (279mm)
CL of sensor
* X”
** 13-1/2”
(343mm)
* 14-3/4” ‡
from top of
xture (toilet)
Urinal top spud
Ø1-1/2” (Ø38mm) hole
* X”, ‡ = At least 5” clearance from sensor to tip of toilet seat up position or
to top of grab bar is required to avoid false detection.
** Opening in wall
Right water supply
1” NPT (toilet), 3/4” (urinal)
12-5/8” (320mm)
11” (280mm)
14-3/16” (360mm)
12-5/8” (320mm)
11-7/8” (301mm)
11” (280mm)
13-3/8” (340mm)
12-5/8” (320mm)
33-1/2"
(850mm)
15°
Max 19-11/16”
(Max 500mm)
/