Hitachi UC 18YML2 Handling Instructions Manual

Page is loading ...

2

English Deutsch Français

1

Rechargeable battery

(BSL1415, BSL1415X)

Akkumulator

(BSL1415, BSL1415X)

Batterie rechargeable

(BSL1415, BSL1415X)

2

Rechargeable battery

(BSL1430)

Akkumulator

(BSL1430)

Batterie rechargeable

(BSL1430)

3

Rechargeable battery

(BSL1815X)

Akkumulator

(BSL1815X)

Batterie rechargeable

(BSL1815X)

4

Rechargeable battery

(BSL1830)

Akkumulator

(BSL1830)

Batterie rechargeable

(BSL1830)

5

Pilot lamp Ladungsstatuslampe Voyant d’état de chargement

6

Guide rail Führungsschiene Glissière

7

Cooling fan Ventilator Ventilateur de refroidissement

8

Caution plate Warnschild Plaque d’avertissement

9

Nameplate Typenschild Plaque signalétique

0

Line Leitung Ligne

!

Strap Band Courroie

@

Connecting socket Anschlussbuchse Prise de raccordement

#

Charger connecting plug Anschlussbuchse des Ladegeräts Prise du chargeur

$

Cigarette lighter connecting plug

Anschlussbuchse des

Zigarettenanzünders

Prise de l’allume-cigare

%

Before insert Vor Einführen Avant insertion

^

After insert Nach Einführen Après insertion

1

2

3

4

#

$

0

% ^

5

!

8

9

@

6

7

12

Page is loading ...

5

Symbols

WARNING

The following show

symbols used for the

machine. Be sure that you

understand their meaning

before use.

Symbole

WARNUNG

Die folgenden Symbole

werden für diese Maschine

verwendet. Achten Sie

darauf, diese vor der

Verwendung zu verstehen.

Symboles

AVERTISSEMENT

Les symboles suivants

sont utilisés pour l’outil.

Bien se familiariser avec

leur signiﬁ cation avant

d’utiliser l’outil.

Simboli

AVVERTENZA

Di seguito mostriamo i

simboli usati per la macchina.

Assicurarsi di comprenderne

il signiﬁ cato prima dell’uso.

Read all safety warnings

and all instructions.

Failure to follow the

warnings and instructions

may result in electric

shock, ﬁ re and/or serious

injury.

Lesen Sie sämtliche

Sicherheitshinweise und

Anweisungen durch.

Wenn die Warnungen

und Anweisungen nicht

befolgt werden, kann es

zu Stromschlag, Brand

und/oder ernsthaften

Verletzungen kommen.

Lire tous les

avertissements de

sécurité et toutes les

instructions.

Tout manquement à observer

ces avertissements et

instructions peut engendrer

des chocs électriques,

des incendies et/ou des

blessures graves.

Leggere tutti gli

avvertimenti di

sicurezza e tutte le

istruzioni.

La mancata osservanza

degli avvertimenti e delle

istruzioni potrebbe essere

causa di scosse elettriche,

incendi e/o gravi lesioni.

Only for EU countries

Do not dispose of electric tools

together with household waste

material!

In observance of European

Directive 2002/96/EC

on waste electrical and

electronic equipment and its

implementation in accordance

with national law, electric tools

that have reached the end of

their life must be collected

separately and returned to an

environmentally compatible

recycling facility.

Nur für EU-Länder

Werfen Sie Elektrowerkzeuge

nicht in den Hausmüll!

Gemäss Europäischer

Richtlinie 2002/96/EG über

Elektro- und Elektronik-

Altgeräte und Umsetzung

in nationales Recht müssen

verbrauchte Elektrowerkzeuge

getrennt gesammelt und

einer umweltgerechten

Wiederververtung zugeführt

werden.

Pour les pays européens

uniquement

Ne pas jeter les appareils

électriques dans les ordures

ménagères!

Conformément à la directive

européenne 2002/96/EG relative

aux déchets d’équipements

électriques ou électroniques

(DEEE), et à sa transposition

dans la législation nationale, les

appareils électriques doivent être

collectés à part et être soumis

à un recyclage respectueux de

l’environnement.

Solo per Paesi UE

Non gettare le apparecchiature

elettriche tra i riﬁ uti domestici.

Secondo la Direttiva Europea

2002/96/CE sui riﬁ uti di

apparecchiature elettriche ed

elettroniche e la sua attuazione

in conformità alle norme

nazionali, le apparecchiature

elettriche esauste devono essere

raccolte separatamente, al ﬁ ne

di essere reimpiegate in modo

eco-compatibile.

Symbolen

WAARSCHUWING

Hieronder staan symbolen

afgebeeld die van

toepassing zijn op deze

machine. U moet de

betekenis hiervan begrijpen

voor gebruik.

Símbolos

ADVERTENCIA

A continuación se

muestran los símbolos

usados para la máquina.

Asegúrese de comprender

su signiﬁ cado antes del

uso.

Símbolos

AVISO

A seguir aparecem os

símbolos utilizados pela

máquina. Assimile bem

seus signiﬁ cados antes

do uso.

Σύμβολα

ΠΡΟΣΟΧΗ

  

  

 

. 

  

   

.

Lees alle

waarschuwingen en

instructies aandachtig

door.

Nalating om de

waarschuwingen en

instructies op te volgen

kan in een elektrische

schok, brand en/of ernstig

letsel resulteren.

Lea todas las

instrucciones y

advertencias de

seguridad.

Si no se siguen

las advertencias e

instrucciones, podría

producirse una descarga

eléctrica, un incendio y/o

daños graves.

Leia todas as instruções

e avisos de segurança.

Se não seguir todas as

instruções e os avisos,

pode provocar um choque

eléctrico, incêndio e/ou

ferimentos graves.

Διαβάζετε όλες τις

προειδοποιήσεις

ασφαλείας και όλες τις

οδηγίες.

   

 

  



, 

/  .

Alleen voor EU-landen

Geef elektrisch gereedschap niet

met het huisvuil mee!

Volgens de Europese richtlijn

2002/96/EG inzake oude

elektrische en elektronische

apparaten en de toepassing

daarvan binnen de nationale

wetgeving, dient gebruikt

elektrisch gereedschap

gescheiden te worden ingezameld

en te worden afgevoerd naar een

recycle bedrijf dat voldoet aan

de

geldende milieu-eisen

.

Sólo para países de la Unión

Europea

¡No deseche los aparatos

eléctricos junto con los residuos

domésticos!

De conformidad con la Directiva

Europea 2002/96/CE sobre

residuos de aparatos eléctricos

y electrónicos y su aplicación

de acuerdo con la legislación

nacional, las herramientas

eléctricas cuya vida útil haya

llegado a su ﬁ n se deberán

recoger por separado y trasladar

a una planta de reciclaje que

cumpla con las exigencias

ecológicas.

Apenas para países da UE

Não deite ferramentas eléctricas

no lixo doméstico!

De acordo com a directiva

europeia 2002/96/CE sobre

ferramentas eléctricas e

electrónicas usadas e a

transposição para as leis

nacionais, as ferramentas

eléctricas usadas devem ser

recolhidas em separado e

encaminhadas a uma instalação

de reciclagem dos materiais

ecológica.

     

   

   

!

   

 2002/ 96/ 

  

   

   , 

   

   

  

  

 

.

Page is loading ...

7

English

GENERAL OPERATIONAL PRECAUTIONS

1. Keep work area clean. Cluttered areas and benches

invite accidents.

2. Avoid dangerous environment. Don’t expose power

tools and charger to rain. Don’t use power tools and

charger in damp or wet locations. And keep work area

well lit.

Never use power tools and charger near ﬂ ammable or

explosive materials.

Do not use tool and charger in presence of ﬂ ammable

liquids or gases.

3. The appliance is not intended for use by young children

or inﬁ rm persons without supervision. Young children

should be supervised to ensure that they do not play

with the appliance. All visitors should be kept safe

distance from work area.

4. Store idle tools and charger. When not in use, tools

and charger should be stored in dry, high or locked-

up place — out of reach or children. Store tools and

charger in a place in which the temperature is less than

40°C.

5. Don’t abuse cord. Never carry charger by cord or yank

it to disconnect from receptacle. Keep cord from heat,

oil and sharp edges.

6. When the charger is not in use or when being

maintained and inspected, disconnect the power cord

of the charger from the receptacle.

7. To avoid danger, always use only the speciﬁ ed

charger.

8. Use only genuine HITACHI replacement parts.

9. Do not use power tools and charger for applications

other than those speciﬁ ed in the Handling Instructions.

10. To avoid personal injury, use only the accessories

or attachment recommended in these handling

instructions or in the HITACHI catalog.

11. If the supply cord is damaged, it must be replaced

by the manufacture or its service agent or a similarly

qualiﬁ ed person in order to avoid a hazard.

Let only the authorized service center do the

repairing. The Manufacture will not be responsible

for any damages or injuries caused by repair by the

unauthorized persons or by mishandling of the tool.

12. To ensure the designed operational integrity of power

tools and charger, do not remove installed covers or

screws.

13. Always use the charger at the voltage speciﬁ ed on the

nameplate.

14. Always charge the battery before use.

15. Never use a battery other than that speciﬁ ed. Do not

connect a usual dry cell, a rechargeable battery other

than that speciﬁ ed or a car battery to the power tool.

16. Do not use a transformer containing a booster.

17. Do not charge the battery from an engine electric

generator.

18. Always charge indoors. Because the charger and

battery heat slightly during charging, charge the

battery in a place not exposed to direct sunlight; where

the humidity is low and the ventilation is good.

19. Use the exploded assembly drawing on this handling

instructions only for authorized servicing.

PRECAUTIONS FOR CHARGER

1. Always charge the battery at an ambient temperature

of 0–40°C. A temperature of less than 0°C will result in

over charging which is dangerous. The battery cannot

be charged at a temperature greater than 40°C.

The most suitable temperature for charging is that of

20–25°C.

2. Do not use the charger continuously.

When one charging is completed, leave the charger for

about 15 minutes before the next charging of battery.

3. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

4. Never disassemble the rechargeable battery or

charger.

5. Never short-circuit the rechargeable battery.

Short-circuiting the battery will cause a great electric

current and overheat. It results in burn or damage to

the battery.

6. Do not dispose of the battery in ﬁ re.

If the battery is burnt, it may explode.

7. Using an exhausted battery will damage the charger.

8. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery life

becomes too short for practical use. Do not dispose of

the exhausted battery.

9. Do not insert objects into the air ventilation slots of the

charger.

Inserting metal objects or ﬂ ammable into the charger

air ventilation slots will result in an electrical shock

hazard or damage to the charger.

PRECAUTIONS WHEN USING THE

BATTERYCHARGER WITH A DC 12V IN-CAR

POWER SOURCE

1. Use the battery charger correctly.

Do not use the battery charger other than with a DC

12V in-car power source. The battery charger is solely

for use on minus-grounded vehicles. Make sure that

the minus pole of the car battery is connected to the

car body.

2. Keep your attention focused on driving the car.

If you use the battery charger while driving, fasten

the battery charger in place so that it does not move

inadvertently and distract your attention from driving.

Do not place the battery charger or battery under the

driver’s seat, irrespective of whether it is charging or

not, as it may get under the brake pedal or the cable

may get wrapped around the driver’s feet and cause an

accident.

3. Do not manipulate the battery charger or battery

while driving as this may cause an accident.

4. Do not leave the battery charger or battery within

reach of children as this may result in an accident.

5. Be sure to use the cable provided.

Using a di erent cable could result in a ﬁ re or

accident due to overheating.

6. Do not place the battery charger on a blanket-type

car seat cover or car mat during charging as this may

result in a ﬁ re or accident due to overheating.

7. Do no expose the battery charger to direct sunlight

during charging as this may result in a ﬁ re.

8. Do not leave the vehicle unattended during charging.

9. Do not charge the battery using an AC power source

and DC 12V in-car power source together.

It causes charging failure and, more importantly, may

result in a ﬁ re.

(Original instructions)

8

English

SPECIFICATION

CHARGER

Model UC18YML2

Power source AC DC12 V (in-Car)

Charging time Approx. 22 – 45 minutes Approx. 60 – 120 minutes

Charging voltage 14.4 – 18 V

Weight 0.7 kg

AC/DC Dual Power Charger included:

Charge battery from AC mains socket or 12V DC car cigarette lighter socket.

APPLICATION

For charging the HITACHI BATTERY

○ BSL1415, BSL1415X, BSL1430, BSL1815X, BSL1830

CHARGING

Before using the power tool, charge the battery as follows.

1. Connect to the power source

When charging the battery from an AC power source

○ Connect the charger’s power cord to the

receptacle.

When connecting the plug of the charger to a

receptacle, the pilot lamp will blink in red (At 1-second

intervals).

CAUTION

Do not use the electrical cord if damaged. Have it

repaired immediately.

When charging the battery from a DC 12V in-car power

source

○ Secure the battery charger in place in the car.

Use the strap supplied with the battery charger to

fasten the battery charger in place and prevent it from

moving inadvertently. (See Fig. 3)

CAUTION

Do not place the battery charger or battery under

the driver’s seat. Secure the battery charger in

place to prevent it from moving inadvertently as

this may lead to an accident.

Fig. 3

○ Insert the cigarette lighter connecting plug into the

cigarette lighter socket.

If the plug is loose and falls out of the cigarette lighter

socket, repair the socket. As the socket may be faulty,

you are recommended to contact your local car dealer.

Continued use of the socket may result in an accident

due to overheating.

2. Insert the battery into the charger.

Firmly insert the battery into the charger until the line is

visible, as shown in Fig. 1, 2.

3. Charging

When inserting a battery in the charger, the pilot lamp

will light up continuously in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red (At 1-second intervals). (See

Table 1)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 1, according to the condition of the charger or

the rechargeable battery.

Table 1

Indications of the pilot lamp

The pilot

lamp

lights or

blinks in

red.

Before

charging

Blinks Lights for 0.5 seconds. Does not light for

0.5 seconds. (o for 0.5 seconds)

While

charging

Lights Lights continuously

Charging

complete

Blinks Lights for 0.5 seconds. Does not light for

0.5 seconds. (o for 0.5 seconds)

Charging

impossible

Flickers Lights for 0.1 seconds. Does not light for

0.1 seconds. (o for 0.1 seconds)

Malfunction in the

battery or the charger

The pilot

lamp

lights or

blinks in

green.

Overheat

standby

Lights Lights continuously

Battery overheated.

Unable to charge.

(Charging will commence

when battery cools)

Charging

with in-car

power source

impossible

Blinks Lights for 0.5 seconds. Does not light for

0.5 seconds. (o for 0.5 seconds)

Malfunction of the car

battery

NOTE: When standby for cooling battery, UC18YML2 cools the overheated battery by cooling fan.

(However, the cooling fan does not function when charging the battery with a DC 12V in-car power source.)

9

English

(2) Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are as

shown in the table below, and batteries that have

become hot should be cooled for a while before being

recharged.

Table 2

Temperatures at which the battery can be recharged

0°C - 50°C

(3) Regarding recharging time

Table 3 shows the recharging time required according

to the type of battery.

Table 3 Recharging time (approx. min.) at 20°C

(AC power supply/DC 12V (in-car) power supply)

Battery capacity (Ah)

Battery

Voltage

(V)

Li-ion BATTERY

1.5 Ah 3.0 Ah

14.4 V

BSL1415

BSL1415X

(4 cells)

22/60

min.

BSL1430

(8 cells)

45/120

min.

18 V

BSL1815X

(5 cells)

22/60

min.

BSL1830

(10 cells)

45/120

min.

NOTE

The recharging time may vary according to the

ambient temperature.

Especially, using a DC 12V in-car power source may

require longer recharging time at high temperatures.

E.g., approx. 170-180 min (3.0 Ah) at 40°C

4. Disconnect the charger’s power cord from the

receptacle or cigarette lighter socket

5. Hold the charger ﬁ rmly and pull out the battery

NOTE

Be sure to pull out the battery from the charger after

use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might be

low when using them the ﬁ rst and second time. This is

a temporary phenomenon, and normal time required

for recharging will be restored by recharging the

batteries 2–3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

CAUTION

○ If the battery is charged while it is heated because

it has been left for a long time in a location subject

to direct sunlight or because the battery has just

been used, the pilot lamp of the charger lights up

green. In such a case, ﬁ rst let the battery cool, then

start charging.

○ When the pilot lamp ﬂ ickers in red (at 0.2-seconds

intervals), check for and take out any foreign objects

in the charger’s battery connector. If there are no

foreign objects, it is probable that the battery or

charger is malfunctioning. Take it to your authorized

Service Center.

○ Since the built-in micro computer takes about 3

seconds to conﬁ rm that the battery being charged

with UC18YML2 is taken out, wait for a minimum

of 3 seconds before reinserting it to continue charging.

If the battery is reinserted within 3 seconds, the battery

may not be properly charged.

○ Check the voltage of the in-car power source when

the pilot lamp ﬂ ickers in green (every 0.2 seconds)

continuously.

If the voltage is 12V or lower, it indicates that the car

battery has weakened and cannot be charged.

○ If the pilot lamp does not blink in red (every second)

even though the charger cord or cigarette lighter

connecting plug is connected to the power, it indicates

that the protection circuit of the charger may be

activated.

Remove the cord or plug from the power and then

connect it again after 30 seconds or so.If this does

not cause the pilot lamp to blink in red (every second),

please take the charger to the Hitachi Authorized

Service Center.

MAINTENANCE AND INSPECTION

1. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure that

they are properly tightened. Should any of the screws

be loose, retighten them immediately. Failure to do so

could result in serious hazard.

2. Cleaning of the charger

When the charger is stained, wipe with a soft dry cloth

or a cloth moistened with soapy water. Do not use

chloric solvents, gasoline or paint thinner, for they melt

plastics.

3. Store idle charger

When not in use, the charger should be stored in dry,

high or locked-up place — out of reach of children.

4. Fuse replacement of cigarette lighter connecting

plug

CAUTION

For continued protection against risk of ﬁ re,

replaceonly with same type and ratings of fuse in

cigarette lighter connecting plug.

250V, 6A, DC

5. Service parts list

CAUTION

Repair, modiﬁ cation and inspection of Hitachi Power

Tools must be carried out by a Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modiﬁ ed to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without prior

notice.

NOTE

Due to HITACHI’s continuing program of research and

development, the speciﬁ cations herein are subject to

change without prior notice.

Page is loading ...

54

䎤

21

9

A

501

502

1

2

3

5

6

8

4

11

12

13

15

16

4

17

6

22

10

20

14

18

7

19

ITEM

NO.

PART NAME Q’TY

1

CAUTION PLATE 1

2CASE (A) 1

3 FILTER 1

4 TP TAPPING SCREW D3 × 84

5FUSE 1

6NUT M3 7

7 INSULATOR (A) 1

8FIN (A) 1

9

MACHINE SCREW (W/WASHERS) M3 × 12

6

10 FIN (B) 1

11 CASE (B) 1

12

TAPPING SCREW (W/FLANGE) D3 × 18

4

13 CASE RUBBER 4

14 NAME PLATE 1

15 PRISM 1

16 TERMINAL HOLDER 1

17 BINDING BAND 1

18 CORD 1

19 PRINTED CIRCUIT BOARD ASS'Y 1

20

TAPPING SCREW (W/FLANGE) D3 × 25

2

21 FAN 1

22 INSULATOR (B) 1

501 STRAP 1

502 DC CORD 1

55

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 willich 1, F. R. Germany

Tel: +49 2154 49930

Fax: +49 2154 499350

URL: http://www.hitachi-powertools.de

Hitachi Power Tools Netherlands B. V.

Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands

Tel: +31 30 6084040

Fax: +31 30 6067266

URL: http://www.hitachi-powertools.nl

Hitachi Power Tools (U. K.) Ltd.

Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ,

United Kingdom

Tel: +44 1908 660663

Fax: +44 1908 606642

URL: http://www.hitachi-powertools.co.uk

Hitachi Power Tools France S. A. S.

Prac del’ Eglantier 22, rue des Crerisiers Lisses, C. E.

1541, 91015 EVRY CEDEX, France

Tel: +33 1 69474949

Fax: +33 1 60861416

URL: http://www.hitachi-powertools.fr

Hitachi Power Tools Belgium N.V. /

S.A.

Koningin Astridlaan 51, 1780 Wemmel, Belgium

Tel: +32 2 460 1720

Fax: +32 2 460 2542

URL http://www.hitachi-powertools.be

Hitachi Fercad Power Tools Italia

S.p.A

Via Retrone 49-36077, Altavilla Vicentina (VI), Italy

Tel: +39 0444 548111

Fax: +39 0444 548110

URL: http://www.hitachi-powertools.it

Hitachi Power Tools lberica, S.A.

C / Migjorn, s/n, Poligono Norte, 08226 Terrassa,

Barcelona, Spain

Tel: +34 93 735 6722

Fax: +34 93 735 7442

URL: http://www.hitachi-powertools.es

Hitachi Power Tools Österreich GmbH

Str. 7, Objekt 58/A6, Industriezentrum NÖ –Süd 2355

Wiener Neudorf, Austria

Tel: +43 2236 64673/5

Fax: +43 2236 63373

Hitachi Power Tools Norway AS

Kjeller Vest 7

Postboks 124, 2007 Kjeller, Norway

Tel: (+47) 6692 6600

Fax: (+47) 6692 6650

URL: http://www.markt.no

Hitachi Power Tools Sweden AB

Rotebergsvagen 2B

SE-192 78 Sollentuna, Sweden

Tel: (+46) 8 598 999 00

Fax: (+46) 8 598 999 40

URL: http://www.markt.se

Hitachi Power Tools Denmark AS

Lillebaeltsvej 90

DK-6715 Esbjerg N, Denmark

Tel: (+45) 75 14 32 00

Fax: (+45) 75 14 36 66

URL: http://www.markt.dk

Hitachi Power Tools Finland OY

Tupalankatu 9

FIN-15680 Lahti, Finland

Tel: (+358) 20 7431 530

Fax: (+358) 20 7431 531

URL: http://www.markt.ﬁ

004

Code No. C99173771 G

Printed in China

English Portugûes

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is in

conformity with standards or standardization documents EN60335,

EN55014 and EN61000 in accordance with Directives 2006/95/EC and

2004/108/EC.

This declaration is applicable to the product a xed CE marking..

DECLARAÇÃO DE CONFORMIDADE CE

Declaramos, sob nossa única e inteira responsabilidade, que este

produto está de acordo com as normas ou documentos normativos

EN60335, EN55014 e EN61000, em conformidade com as Directrizes

2006/95/CE e 2004/108/CE.

Esta declaração se aplica aos produtos designados CE.

Deutsch 

ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN

Wir erklären mit alleiniger Verantwortung, dass dieses Produkt den

Standards oder Standardisierungsdokumenten EN60335, EN55014

und EN61000 in Übereinstimmung mit den Direktiven 2006/95/CE und

2004/108/CE entspricht.

Diese Erklärung gilt für Produkte, die die CE-Markierung tragen.

  

        

        

60335, 55014  61000     

2006/95/  2004/108/.

         .

Français Svenska

DECLARATION DE CONFORMITE CE

Nous déclarons sous notre seule et entière responsabilité que ce

produit est conforme aux normes ou documents de normalisation

EN60335, EN55014 et EN61000 en accord avec les Directives

2006/95CE et 2004/108/CE.

Cette déclaration s’applique aux produits désignés CE.

EF-DEKLARATION BETRÄFFANDE LIKFORMIGHET

Vi tillkännagiver med eget ansvar att denna produkt överensstämmer

med standard eller standardiserings dokument EN60335, EN55014

och EN61000 i enlighet med direktiven 2006/95/EF och 2004/108/EF.

Denna deklaration gäller för CE-märkningen pà produkten.

Italiano

Dansk

DICHIARAZIONE DI CONFORMITÀ CE

Dichiariamo sotto nostra responsabilità che questo prodotto è

conforme agli standard o ai documenti sulla standardizzazione

EN60335, EN55014 e EN61000 in conformità alle Direttive 2006/95/

CE, e 2004/108/CE.

Questa dichiarazione è applicabile ai prodotti cui sono applicati i

marchi CE.

EF-OVERENSS TEMMELSESERKLÆRING

Vi erlkærer os fuldstændige ansvarlige for, at dette produkt modsvarer

gældende standard eller standardiserings dokumenter EN60335,

EN55014 og EN61000 i overens-stemmelse med direktiver 2006/95/

EF og 2004/108/EF.

Denne erklæring qælder produkter, der er mærket med CE.

Nederlands Norsk

EC VERKLARING VAN CONFORMITEIT

Wij verklaren onder eigen verantwoordelijkheid dat dit product

conform de richtlijnen of gestandardiseerde documenten EN60335,

EN55014 en EN61000 voldoet aan de eisen van bepalingen 2006/95/

EC en 2004/108/EC.

Deze verklaring is van toepassing op produkten voorzien van de CE-

markeringen.

EF’s ERKLÆRING OM OVERENSSTEMMELSE

Vi erklærer herved at vi påtar oss det fulle ansvar for at

dette produktet er i overensstemmelse med normer eller

standardiseringsdokumentene EN60335, EN55014 og EN61000 i

samsvar med direktivene 2006/95/EF og 2004/108/EF.

Denne erklæringen gjelder produktets påklistrede CE-merking.

Español Suomi

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra única responsabilidad que este producto

está Declaramos bajo nuestra única responsabilidad que este

producto está de acuerdo con las normas o con los documentos de

normalización EN60335, EN55014 y EN61000, según indican las

Directrices 2006/95/CE y 2004/108/CE.

Esta declaración se aplica a los productos con marcas de la CE.

EY-ILMOITUS YHDENMUKAISUUDESTA

Yksinomaisella vastuudella vakuutamme, että tämä tuote vastaa tai

normitettuja dokumentteja EN60335, EN55014 ja EN61000 ohjeiden

2006/95/EY ja 2004/108/EY mukaisesti.

Tämä ilmoitus sovelletaan tuotekohtaiseen CE-merkintään.

Representative o ce in Europe

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 Willich 1, F. R. Germany

Head o ce in Japan

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo, Japan

29. 4. 2010

K. Kato

Board Director

Hitachi UC 18YML2 Handling Instructions Manual

Hitachi UC 18YML2 Handling Instructions Manual

in other languages

Related papers

Other documents