Lenovo 07632VU User manual

Lenovo 3000 V100 and V200

Hard ware

Maintenance Manual

May 2007

This manual supports:

Lenovo 3000 V100 and V200

(MT 0763 and 0764)

Lenovo 3000 V100 and V200

Hard ware

Maintenance Manual

Note

Before using this information and the product it supports, be sure to read the general information under “Notices” on page

117.

First Edition (May 2007)

U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with

RESTRICTED RIGHTS. Use, duplication or disclosure by the Government is subject to the GSA ADP Schedule

contract with Lenovo, if any, or the standard terms of this commercial license, or if the agency is

unable to accept this Program under these terms, then we provide this Program under the provisions set forth in

Commercial Computer Software–Restricted Rights at FAR 52.227-19, when applicable, or under Rights in

Data-General, FAR 52.227.14 (Alternate III).

Contents

Introduction . . . . . . . . . . . . .1

About this manual . . . . . . . . . . . .1

Important service information . . . . . . . .1

Strategy for replacing FRUs . . . . . . . . .1

Strategy for replacing a hard disk drive . . . .2

Important notice for replacing a system board . .2

How to use error messages . . . . . . . .2

Strategy for replacing FRUs for Custom Model

Variant (CMV) products . . . . . . . . . .2

Using PC Entitlement Warehouse (PEW) . . . .3

Using eSupport . . . . . . . . . . . .3

Using the HMM . . . . . . . . . . . .3

Important information about replacing RoHS

compliant FRUs . . . . . . . . . . . . .4

Diskette compatibility matrix . . . . . . . . .5

Safety notices: multilingual translations . . . . .5

Safety information . . . . . . . . . . . .11

General safety . . . . . . . . . . . .11

Electrical safety . . . . . . . . . . . .11

Safety inspection guide . . . . . . . . .13

Handling devices that are sensitive to

electrostatic discharge . . . . . . . . . .14

Grounding requirements . . . . . . . . .14

Laser compliance statement . . . . . . . . .15

General descriptions . . . . . . . . .17

Read this first . . . . . . . . . . . . .17

What to do first . . . . . . . . . . . .17

Related service information . . . . . . . . .19

Service Web site . . . . . . . . . . . .19

Restoring the factory contents by using Product

Recovery discs . . . . . . . . . . . .19

Passwords . . . . . . . . . . . . . .20

Power management . . . . . . . . . .22

Checkout guide . . . . . . . . . . . . .24

Testing the computer . . . . . . . . . .24

Detecting system information with PC-Doctor . .26

Power system checkout . . . . . . . . .26

Lenovo 3000 V100 and V200 . . . . .29

Product overview . . . . . . . . . . . .30

Specifications . . . . . . . . . . . . .30

Status indicators . . . . . . . . . . . .33

FRU tests . . . . . . . . . . . . . .34

Fn key combinations . . . . . . . . . .35

Symptom-to-FRU index . . . . . . . . . .36

Numeric error codes . . . . . . . . . .36

Error messages . . . . . . . . . . . .38

Beep symptoms . . . . . . . . . . . .39

No-beep symptoms . . . . . . . . . . .39

LCD-related symptoms . . . . . . . . .40

Intermittent problems . . . . . . . . . .41

Undetermined problems . . . . . . . . .41

FRU replacement notices . . . . . . . . . .42

Screw notices . . . . . . . . . . . . .42

Retaining serial numbers . . . . . . . . .42

Removing and replacing a FRU . . . . . . . .45

1010 Battery pack . . . . . . . . . . .46

1020 Hard disk drive slot cover and hard disk

drive . . . . . . . . . . . . . . .47

1030 DIMM slot cover . . . . . . . . . .49

1040 DIMM . . . . . . . . . . . . .49

1050 Backup battery . . . . . . . . . .50

1060 PCI Express Mini Card slot cover and PCI

Express Mini Card for 802.11 a/b/g wireless

LAN . . . . . . . . . . . . . . . .51

1070 PCI Express Mini Card slot cover and PCI

Express Mini Card 802.11 a/b/g/n wireless LAN 52

1080 Optical drive . . . . . . . . . . .55

1090 Middle cover . . . . . . . . . . .55

1100 Function board . . . . . . . . . .56

1110 Keyboard . . . . . . . . . . . .57

1120 Hinge covers, keyboard bezel, 5-1 Digital

Media Reader card, BDC, and fingerprint reader

card . . . . . . . . . . . . . . . .59

1130 LCD unit . . . . . . . . . . . .67

1140 Heat sink assembly, CPU, MDC,

ExpressCard slot, and system board . . . . .70

1150 Fan and base cover (with speakers) . . . .77

2010 LCD front bezel . . . . . . . . . .79

2020 Inverter card . . . . . . . . . . .80

2030 Integrated camera . . . . . . . . .81

2040 LCD panel, LCD cable, and hinges . . . .82

2050 Wireless LAN antenna cables . . . . . .84

Locations . . . . . . . . . . . . . . .86

Front view . . . . . . . . . . . . . .86

Rear view . . . . . . . . . . . . . .87

Bottom view . . . . . . . . . . . . .87

Parts list . . . . . . . . . . . . . . .88

Overall . . . . . . . . . . . . . . .89

LCD FRUs . . . . . . . . . . . . . 101

Keyboard . . . . . . . . . . . . . . 103

Recovery discs . . . . . . . . . . . . 105

Corel software CDs . . . . . . . . . .114

Miscellaneous parts . . . . . . . . . .114

AC adapters . . . . . . . . . . . . .115

Common parts list . . . . . . . . . . .115

Notices . . . . . . . . . . . . . . .117

Trademarks . . . . . . . . . . . . . .118

iv MT 0763 and 0764

Introduction

About this manual

This manual contains service and reference information for Lenovo 3000 V100 and

V200 (MT 0763 and 0764). Use this manual along with the advanced diagnostic

tests to troubleshoot problems.

The manual is divided into sections as follows:

v The common sections provide general information, guidelines, and safety

information required in servicing computers.

v The product-specific section includes service, reference, and product-specific

parts information.

Important

This manual is intended for trained service personnel who are familiar with

Lenovo 3000 products. Use this manual along with the advanced diagnostic

tests to troubleshoot problems effectively.

Before servicing a Lenovo 3000 product, be sure to review the safety

information under “Safety notices: multilingual translations” on page 5,

“Safety information” on page 11, and “Laser compliance statement” on page

15.

Important service information

Important

BIOS and device driver fixes are customer-installable. The BIOS and device

drivers are posted on the customer support site http://www.lenovo.com/

support

Advise customers to contact the Customer Support Center at 800-426-7378 if

they need assistance in obtaining or installing any software fixes, drivers, and

BIOS downloads.

Customers in Canada should call the Customer Support Center at

800-565-3344 for assistance or download information.

Strategy for replacing FRUs

Before replacing parts

Make sure that all software fixes, drivers, and BIOS downloads are installed

before replacing any FRUs listed in this manual.

Use the following strategy to prevent unnecessary expense for replacing and

servicing FRUs:

v If you are instructed to replace a FRU but the replacement does not correct the

problem, reinstall the original FRU before you continue.

v Some computers have both a processor board and a system board. If you are

instructed to replace either the processor board or the system board, and

replacing one of them does not correct the problem, reinstall that board, and

then replace the other one.

v If an adapter or a device consists of more than one FRU, any of the FRUs may

be the cause of the error. Before replacing the adapter or device, remove the

FRUs, one by one, to see if the symptoms change. Replace only the FRU that

changed the symptoms.

Attention: The setup configuration on the computer you are servicing may have

been customized. Running Automatic Configuration may alter the settings. Note

the current configuration settings (using the View Configuration option); then,

when service has been completed, verify that those settings remain in effect.

Strategy for replacing a hard disk drive

Always try to run a low-level format before replacing a hard disk drive.

Attention: The drive startup sequence in the computer you are servicing may

have been changed. Be extremely careful during write operations such as copying,

saving, or formatting. If you select an incorrect drive, data or programs can be

overwritten.

Important notice for replacing a system board

Some components mounted on a system board are very sensitive. Improper

handling of a system board can cause damage to those components, and may

cause a system malfunction.

Attention: When handling a system board:

v Do not drop a system board or apply any excessive force to it.

v Avoid rough handling of any kind.

v Avoid bending a system board and hard pushing to prevent cracking at each

BGA (Ball Grid Array) chipset.

How to use error messages

Use the error codes displayed on the screen to diagnose failures. If more than one

error code is displayed, begin the diagnosis with the first error code. Whatever

causes the first error code may also cause false error codes. If no error code is

displayed, see whether the error symptom is listed in the Symptom-to-FRU Index

for the computer you are servicing.

Strategy for replacing FRUs for Custom Model Variant (CMV) products

Custom Model Variant (CMV) is a unique configuration that has been negotiated

between Lenovo

TM

and the customer. A unique 4-digit MT and 3-digit model is

provided to the customer to place orders (Example: 1829-W15). A CMV is a special

bid offering. Therefore, it is NOT generally announced.

There are three information resources to identify which FRUs are used to support

CMV products. These sources are PC Entitlement Warehouse (PEW), eSupport, and

the HMM.

Important service information

2 MT 0763 and 0764

Using PC Entitlement Warehouse (PEW)

v PEW is the primary source for identifying FRU part numbers and FRU

descriptions for the key commodities for CMV products at a MT - serial number

level. An example of key commodities are hard disk drives, system boards,

microprocessors, Liquid Crystal Displays (LCDs), and memory.

v Remember, all CMV products are loaded in PEW under the 4-digit MT and

3-digit model, where model = “fixed part number”.

v PEW can be accessed at the following Web site:

http://w3-3.ibm.com/pc/entitle

Customers can also access PEW via

http://www-307.ibm.com/pc/support/site.wss/product.do?template=/

warranty/warranty.vm&sitestyle=lenovo

Click

on MACHINE LOOKUP, followed by WARRANTY INFORMATION. Input

the MT and the Serial number and the list of key commodities will be returned

in the PEW record under COMPONENT INFORMATION.

v Business Partners using Eclaim will access PEW when performing Entitlement

Lookup. Business Partners will enter Loc ID, MT and Serial, and the key

commodities will be returned in the Eclaim record under SYSTEM DETAILS.

v Authorized IBM

®

Business Partners can access Eclaim at the following Web site:

https://wca.eclaim.com

Using eSupport

For Key Commodities (Examples - hard disk drive, system board,

microprocessor, LCD, and memory)

v eSupport can be used to view the list of key commodities built in a particular

machine serial (this is the same record found in PEW).

v eSupport can be accessed at the following Web site: http://www.lenovo.com/

support

v To view the key commodities, click on PARTS INFORMATION, then PARTS

LOOKUP. Type in the model type and serial number. The key commodities will

be returned in the eSupport record under PARTS SHIPPED WITH YOUR

SYSTEM.

For the Remaining FRUs (the complete list of FRUs at the MT Model level)

v eSupport can be used to view the complete list of FRUs for a machine type and

model.

v To view the complete list of FRUs, type in the machine type and model

(Example: 1829-CTO) under QUICK PATH. Under “View by Document Type”

select PARTS INFORMATION. Under “Filter by Category” select SERVICE

PARTS. Under “Parts Information by Date” select SYSTEM SERVICE PARTS. The

list of service parts by description, with applicable machine type model and FRU

will be displayed.

Using the HMM

Use the HMM as a back-up to PEW and eSupport to view the complete list of

FRUs at the MT Model level. CMVs are custom models and are not found in the

HMM.

Important service information

Introduction 3

Important information about replacing RoHS compliant FRUs

RoHS, The Restriction of Hazardous Substances in Electrical and Electronic

Equipment Directive (2002/95/EC) is a European Union legal requirement

affecting the global electronics industry. RoHS requirements must be

implemented on Lenovo products placed on the market after June 2006. Products

on the market before June 2006 are not required to have RoHS compliant parts.

So, if the original FRU parts are non compliant, replacement parts can also be

non compliant. In all cases if the original FRU parts are RoHS compliant the

replacement part must also be RoHS compliant.

Lenovo plans to transition to RoHS compliance well before the implementation

date and expects its suppliers to be ready to support Lenovo's requirements and

schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The

following statement pertains to these products and any product Lenovo produces

containing RoHS compliant FRUs.

RoHS compliant FRUs have unique FRU part numbers. Before or after the RoHS

implementation date, failed RoHS compliant parts must always be replaced using

RoHS compliant FRUs, so only the FRUs identified as compliant in the system

HMM or direct substitutions for those FRUs may be used.

Products marketed before June 2006 Products marketed after June 2006

Current or original

part

Replacement FRU Current or original

part

Replacement FRU

Non-RoHS Can be Non-RoHS Must be RoHS Must be RoHS

Non-RoHS Can be RoHS

Non-RoHS Can sub to RoHS

RoHS Must be RoHS

Note: A direct substitution is a part with a different FRU part number that is

automatically shipped by the distribution center at the time of the order.

Important service information

4 MT 0763 and 0764

Diskette compatibility matrix

The compatibility of each of the drives with the diskettes for it is as follows:

Diskette

drive

Diskette

capacity

Compatibility

3.5-inch 1.0 MB Read and write

2.0 MB Read and write

4.0 MB Not compatible

Safety notices: multilingual translations

In this manual, safety notices appear in English with a page number reference to

the appropriate multilingual, translated safety notice found in this section.

The following safety notices are provided in English, French, German, Hebrew,

Italian, and Spanish.

Safety notice 1

Before the computer is powered on after FRU replacement, make sure all screws, springs,

and other small parts are in place and are not left loose inside the computer. Verify this

by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes

can cause electrical shorts.

Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle,

vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour

ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces

métalliques ou des copeaux de métal pourraient causer un court-circuit.

Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß

sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im

Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche

geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen.

Prima di accendere l’elaboratore dopo che é stata effettuata la sostituzione di una FRU,

accertarsi che tutte le viti, le molle e tutte le altri parti di piccole dimensioni siano nella

corretta posizione e non siano sparse all’interno dell’elaboratore. Verificare ciò scuotendo

l’elaboratore e prestando attenzione ad eventuali rumori; eventuali parti o pezzetti

metallici possono provocare cortocircuiti pericolosi.

Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los

tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran

sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles

ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos.

Diskette compatibility matrix

Introduction 5

Safety notice 2

DANGER

Some standby batteries contain a small amount of nickel and cadmium. Do not

disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.

Dispose of the battery as required by local ordinances or regulations. Use only the

battery in the appropriate parts listing. Use of an incorrect battery can result in

ignition or explosion of the battery.

Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez

pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau. Ne les mettez pas en

court-circuit. Pour les mettre au rebut, conformez-vous à la réglementation en vigueur.

Lorsque vous remplacez la pile de sauvegarde ou celle de l’horloge temps réel, veillez

à n’utiliser que les modèles cités dans la liste de pièces détachées adéquate. Une

batterie ou une pile inappropriée risque de prendre feu ou d’exploser.

Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann

geringe Mengen Nickel und Cadmium enthalten. Sie darf nur durch die Verkaufsstelle

oder den IBM Kundendienst ausgetauscht werden. Sie darf nicht zerlegt,

wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Die

Batterie kann schwere Verbrennungen oder Verätzungen verursachen. Bei der

Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen der

Bereitschafts-oder Systembatterie nur Batterien des Typs verwenden, der in der

Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien kann zu Entzündung oder

Explosion führen.

Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio. Non

smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle. Smaltirle

secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni

locali). Quando si sostituisce la batteria dell’RTC (real time clock) o la batteria di

supporto, utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di

una batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria

stessa.

Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio. No

las desmonte, ni recargue, ni las eche al fuego o al agua ni las cortocircuite.

Deséchelas tal como dispone la normativa local. Utilice sólo baterías que se

encuentren en la lista de piezas. La utilización de una batería no apropiada puede

provocar la ignición o explosión de la misma.

Safety notices

6 MT 0763 and 0764

Safety notice 3

DANGER

The battery pack contains small amounts of nickel. Do not disassemble it, throw it

into fire or water, or short-circuit it. Dispose of the battery pack as required by local

ordinances or regulations. Use only the battery in the appropriate parts listing when

replacing the battery pack. Use of an incorrect battery can result in ignition or

explosion of the battery.

La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.

Ne la mettez pas en court-circuit. Pour la mettre au rebut, conformez-vous à la

réglementation en vigueur. Lorsque vous remplacez la batterie, veillez à n’utiliser que

les modèles cités dans la liste de pièces détachées adéquate. En effet, une batterie

inappropriée risque de prendre feu ou d’exploser.

Akkus enthalten geringe Mengen von Nickel. Sie dürfen nicht zerlegt,

wiederaufgeladen, kurzgeschlossen, oder Feuer oder Wasser ausgesetzt werden. Bei

der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Beim Ersetzen

der Batterie nur Batterien des Typs verwenden, der in der Ersatzteilliste aufgeführt ist.

Der Einsatz falscher Batterien kann zu Entzündung oder Explosion führen.

La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco o

nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82,

successive disposizioni e disposizioni locali). Quando si sostituisce la batteria,

utilizzare soltanto i tipi inseriti nell’appropriato Catalogo parti. L’impiego di una

batteria non adatta potrebbe determinare l’incendio o l’esplosione della batteria stessa.

Las baterías contienen pequeñas cantidades de níquel. No las desmonte, ni recargue,

ni las eche al fuego o al agua ni las cortocircuite. Deséchelas tal como dispone la

normativa local. Utilice sólo baterías que se encuentren en la lista de piezas al

sustituir la batería. La utilización de una batería no apropiada puede provocar la

ignición o explosión de la misma.

Safety notices

Introduction 7

Safety notice 4

DANGER

The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it,

remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate

it, or expose its cell contents to water. Dispose of the battery as required by local

ordinances or regulations. Use only the battery in the appropriate parts listing. Use of

an incorrect battery can result in ignition or explosion of the battery.

La pile de sauvegarde contient du lithium. Elle présente des risques d’incendie,

d’explosion ou de brûlures graves. Ne la rechargez pas, ne retirez pas son connecteur

polarisé et ne la démontez pas. Ne l’exposez pas à une temperature supérieure à 100°C,

ne la faites pas brûler et n’en exposez pas le contenu à l’eau. Mettez la pile au rebut

conformément à la réglementation en vigueur. Une pile inappropriée risque de

prendre feu ou d’exploser.

Die Systembatterie ist eine Lithiumbatterie. Sie kann sich entzünden, explodieren

oder schwere Verbrennungen hervorrufen. Batterien dieses Typs dürfen nicht

aufgeladen, zerlegt, über 100 C erhitzt oder verbrannt werden. Auch darf ihr Inhalt

nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte

Verbindungsstecker entfernt werden. Bei der Entsorgung die örtlichen Bestimmungen

für Sondermüll beachten. Beim Ersetzen der Batterie nur Batterien des Typs

verwenden, der in der Ersatzteilliste aufgeführt ist. Der Einsatz falscher Batterien

kann zu Entzündung oder Explosion führen.

La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare

gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla,

riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla

in acqua. Smaltirla secondo la normativa in vigore (DPR 915/82, successive

disposizioni e disposizioni locali). L’impiego di una batteria non adatta potrebbe

determinare l’incendio o l’esplosione della batteria stessa.

La batería de repuesto es una batería de litio y puede provocar incendios, explosiones

o quemaduras graves. No la recargue, ni quite el conector polarizado, ni la desmonte,

ni caliente por encima de los 100°C (212°F), ni la incinere ni exponga el contenido de

sus celdas al agua. Deséchela tal como dispone la normativa local.

Safety notices

8 MT 0763 and 0764

Safety notice 5

Safety notice 6

DANGER

If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your

hands, immediately wash the affected areas with water for at least 15 minutes. Seek

medical care if any symptoms from the fluid are present after washing.

Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux

ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze

minutes. Consultez un médecin si des symptômes persistent après le lavage.

Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die

örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas

und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den

Boden fällt. Wenn der Bildschirm beschädigt ist und die darin befindliche Flüssigkeit in

Kontakt mit Haut und Augen gerät, sollten die betroffenen Stellen mindestens 15

Minuten mit Wasser abgespült und bei Beschwerden anschließend ein Arzt aufgesucht

werden.

Nel caso che caso l’LCD si dovesse rompere ed il liquido in esso contenuto entrasse in

contatto con gli occhi o le mani, lavare immediatamente le parti interessate con acqua

corrente per almeno 15 minuti; poi consultare un medico se i sintomi dovessero

permanere.

Si la LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos,

lave inmediatamente las áreas afectadas con agua durante 15 minutos como mínimo.

Obtenga atención medica si se presenta algún síntoma del fluido despues de lavarse.

To avoid shock, do not remove the plastic cover that protects the lower part of the

inverter card.

Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique

protégeant la partie inférieure de la carte d’alimentation.

Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der

Spannungswandlerplatine umgibt, nicht entfernen.

Per evitare scosse elettriche, non rimuovere la copertura in plastica che avvolge la

parte inferiore della scheda invertitore.

Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la

tarjeta invertida.

Safety notices

Introduction 9

Safety notice 7

DANGER

Safety notice 8

DANGER

Though the main batteries have low voltage, a shorted or grounded battery can

produce enough current to burn personnel or combustible materials.

Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise

à la masse d’une batterie peut produire suffisamment de courant pour brûler des

matériaux combustibles ou causer des brûlures corporelles graves.

Obwohl Hauptbatterien eine niedrige Spannung haben, können sie doch bei

Kurzschluß oder Erdung genug Strom abgeben, um brennbare Materialien zu

entzünden oder Verletzungen bei Personen hervorzurufen.

Sebbene le batterie di alimentazione siano a basso voltaggio, una batteria in corto

circuito o a massa può fornire corrente sufficiente da bruciare materiali combustibili o

provocare ustioni ai tecnici di manutenzione.

Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o

con contacto a tierra puede producir la corriente suficiente como para quemar material

combustible o provocar quemaduras en el personal.

Before removing any FRU, power off the computer, unplug all power cords from

electrical outlets, remove the battery pack, and then disconnect any interconnecting

cables.

Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension,

débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la

batterie et déconnectez tous les cordons d’interface.

Die Stromzufuhr muß abgeschaltet, alle Stromkabel aus der Steckdose gezogen, der

Akku entfernt und alle Verbindungskabel abgenommen sein, bevor eine FRU entfernt

wird.

Prima di rimuovere qualsiasi FRU, spegnere il sistema, scollegare dalle prese elettriche

tutti i cavi di alimentazione, rimuovere la batteria e poi scollegare i cavi di

interconnessione.

Antes de quitar una FRU, apague el sistema, desenchufe todos los cables de las tomas

de corriente eléctrica, quite la batería y, a continuación, desconecte cualquier cable de

conexión entre dispositivos.

Safety notices

10 MT 0763 and 0764

Safety information

The following section presents safety information with which you need to be

familiar before you service a Lenovo 3000 computer.

General safety

Follow these rules to ensure general safety:

v Observe good housekeeping in the area of the machines during and after

maintenance.

v When lifting any heavy object:

1. Make sure that you can stand safely without slipping.

2. Distribute the weight of the object equally between your feet.

3. Use a slow lifting force. Never move suddenly or twist when you attempt to

lift.

4. Lift by standing or by pushing up with your leg muscles; this action removes

the strain from the muscles in your back. Do not attempt to lift any object that

weighs more than 16 kg (35 lb) or that you think is too heavy for you.

v

Do not perform any action that causes hazards to the customer, or that makes

the equipment unsafe.

v Before you start the machine, make sure that other service representatives and

the customer’s personnel are not in a hazardous position.

v Place removed covers and other parts in a safe place, away from all personnel,

while you are servicing the machine.

v Keep your toolcase away from walk areas so that other people will not trip over

it.

v Do not wear loose clothing that can be trapped in the moving parts of a

machine. Make sure that your sleeves are fastened or rolled up above your

elbows. If your hair is long, fasten it.

v Insert the ends of your necktie or scarf inside clothing or fasten it with a

nonconductive clip, about 8 centimeters (3 inches) from the end.

v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your

clothing.

Attention: Metal objects are good electrical conductors.

v Wear safety glasses when you are hammering, drilling, soldering, cutting wire,

attaching springs, using solvents, or working in any other conditions that might

be hazardous to your eyes.

v After service, reinstall all safety shields, guards, labels, and ground wires.

Replace any safety device that is worn or defective.

v Reinstall all covers correctly before returning the machine to the customer.

v Fan louvers on the machine help to prevent overheating of internal components.

Do not obstruct fan louvers or cover them with labels or stickers.

Electrical safety

Observe the following rules when working on electrical equipment.

Safety information

Introduction 11

Important

Use only approved tools and test equipment. Some hand tools have handles

covered with a soft material that does not insulate you when working with

live electrical currents.

Many customers have, near their equipment, rubber floor mats that contain

small conductive fibers to decrease electrostatic discharges. Do not use this

type of mat to protect yourself from electrical shock.

v Find the room emergency power-off (EPO) switch, disconnecting switch, or

electrical outlet. If an electrical accident occurs, you can then operate the switch

or unplug the power cord quickly.

v Do not work alone under hazardous conditions or near equipment that has

hazardous voltages.

v Disconnect all power before:

– Performing a mechanical inspection

– Working near power supplies

– Removing or installing main units

v

Before you start to work on the machine, unplug the power cord. If you cannot

unplug it, ask the customer to power-off the wall box that supplies power to the

machine, and to lock the wall box in the off position.

v If you need to work on a machine that has exposed electrical circuits, observe the

following precautions:

– Ensure that another person, familiar with the power-off controls, is near you.

Attention: Another person must be there to switch off the power, if

necessary.

– Use only one hand when working with powered-on electrical equipment;

keep the other hand in your pocket or behind your back.

Attention: An electrical shock can occur only when there is a complete

circuit. By observing the above rule, you may prevent a current from passing

through your body.

– When using testers, set the controls correctly and use the approved probe

leads and accessories for that tester.

– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you

from grounds such as metal floor strips and machine frames.

Observe the special safety precautions when you work with very high voltages;

Instructions for these precautions are in the safety sections of maintenance

information. Use extreme care when measuring high voltages.

v Regularly inspect and maintain your electrical hand tools for safe operational

condition.

v Do not use worn or broken tools and testers.

v Never assume that power has been disconnected from a circuit. First, check that it

has been powered off.

v Always look carefully for possible hazards in your work area. Examples of these

hazards are moist floors, nongrounded power extension cables, power surges,

and missing safety grounds.

v Do not touch live electrical circuits with the reflective surface of a plastic dental

mirror. The surface is conductive; such touching can cause personal injury and

machine damage.

Safety information

12 MT 0763 and 0764

v Do not service the following parts with the power on when they are removed

from their normal operating places in a machine:

– Power supply units

– Pumps

– Blowers and fans

– Motor generators

and similar units. (This practice ensures correct grounding of the units.)

v If an electrical accident occurs:

– Use caution; do not become a victim yourself.

– Switch off power.

– Send another person to get medical aid.

Safety inspection guide

The purpose of this inspection guide is to assist you in identifying potentially

unsafe conditions. As each machine was designed and built, required safety items

were installed to protect users and service personnel from injury. This guide

addresses only those items. You should use good judgment to identify potential

safety hazards due to attachment of non-Lenovo 3000 features or options not

covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent

hazard could be and whether you can continue without first correcting the

problem.

Consider these conditions and the safety hazards they present:

v Electrical hazards, especially primary power (primary voltage on the frame can

cause serious or fatal electrical shock)

v Explosive hazards, such as a damaged CRT face or a bulging capacitor

v Mechanical hazards, such as loose or missing hardware

To

determine whether there are any potentially unsafe conditions, use the

following checklist at the beginning of every service task. Begin the checks with

the power off, and the power cord disconnected.

Checklist:

1. Check exterior covers for damage (loose, broken, or sharp edges).

2. Power off the computer. Disconnect the power cord.

3. Check the power cord for:

a. A third-wire ground connector in good condition. Use a meter to measure

third-wire ground continuity for 0.1 ohm or less between the external

ground pin and the frame ground.

b. The power cord should be the type specified in the parts list.

c. Insulation must not be frayed or worn.

4. Remove the cover.

5. Check for any obvious non-Lenovo 3000 alterations. Use good judgment as to

the safety of any non-Lenovo 3000 alterations.

6. Check inside the unit for any obvious unsafe conditions, such as metal filings,

contamination, water or other liquids, or signs of fire or smoke damage.

7. Check for worn, frayed, or pinched cables.

8. Check that the power-supply cover fasteners (screws or rivets) have not been

removed or tampered with.

Safety information

Introduction 13

Handling devices that are sensitive to electrostatic discharge

Any computer part containing transistors or integrated circuits (ICs) should be

considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when

there is a difference in charge between objects. Protect against ESD damage by

equalizing the charge so that the machine, the part, the work mat, and the person

handling the part are all at the same charge.

Notes

1. Use product-specific ESD procedures when they exceed the requirements

noted here.

2. Make sure that the ESD protective devices you use have been certified

(ISO 9000) as fully effective.

When handling ESD-sensitive parts:

v Keep the parts in protective packages until they are inserted into the product.

v Avoid contact with other people.

v Wear a grounded wrist strap against your skin to eliminate static on your body.

v Prevent the part from touching your clothing. Most clothing is insulative and

retains a charge even when you are wearing a wrist strap.

v Use the black side of a grounded work mat to provide a static-free work surface.

The mat is especially useful when handling ESD-sensitive devices.

v Select a grounding system, such as those listed below, to provide protection that

meets the specific service requirement.

Note

The use of a grounding system to guard against ESD damage is desirable

but not necessary.

– Attach the ESD ground clip to any frame ground, ground braid, or green-wire

ground.

– When working on a double-insulated or battery-operated system, use an ESD

common ground or reference point. You can use coax or connector-outside

shells on these systems.

– Use the round ground prong of the ac plug on ac-operated computers.

Grounding requirements

Electrical grounding of the computer is required for operator safety and correct

system function. Proper grounding of the electrical outlet can be verified by a

certified electrician.

Safety information

14 MT 0763 and 0764

Page is loading ...

Lenovo 07632VU User manual

Lenovo 07632VU User manual

Related papers

Other documents