Genie RB709U-NB User manual

Genie
Brand
Genie
Model
RB709U-NB
Category
Garage Door Opener
Type
User manual
RB709U-NB
Relay Output Universal Receiver
Owner’s Manual
The RB709U-NB digital receiver is a
wireless radio control designed for
use with automated gate openers and
garage door openers. The receiver
has two channels for receiving sig-
nals from two activation devices; i.e.
transmitters, multi-button transmitters,
wireless keypads, etc.
www.gtoaccess.com
Specifications
Compatible transmitter:
•GTOgraynarrowbandtransmitters(318MHz)
Power input:
•8-24Vac/dc,10mastandby,40maactivated(Red&Blackwires).
Outputs:2channelspulsedoutputs
•2channelsdry-contactnormallyopenrelayoutputs.
•Channel1:Blue(N/OContact)&Green(COM)wires.
•Channel2:Yellow(N/OContact)&Brown(COM)wires.
•Activatedfor.5secondswhenthecorrecttransmittercodeisreceived.
•Relayswitchingmaximumrating:24Vac/dc@1A.
•OperatingRange50to100feet(15.2to30.5m)
Indoor/Outdoorcompatible.
Mountreceiveratleast3feetfromACpowersource.
Mounting the Receiver Connect Receiver to Relay Inputs and Power
Consider the following when mounting the receiver:
•Standardreceivercablelengthis10feet(3.05m).
•Forexteriorapplicationsrunthecablethrough
PVCconduittoprotectitfromdamage.
•DONOTruncableinconduitcontainingacwiring.
•Thereceiverrangecanvaryfrom50to100
feet(15.2to30.5m)dependinguponweather,
topography,andexternalinterference.
FCC Regulation
This device complies with FCC rules Part 15. Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept an interference that may cause undesired operation.
Transmitter distance may vary due to circumstances beyond our control. NOTE: The manufacturer
is not responsible for any radio or TV interference caused by unauthorized modifications to this
equipment. Such modifications could void the user’s authority to operate the equipment.
NOTE: Do not mount upside down.
Channel 1 (To COM)
Channel 1 (To N/O Contact)
Channel 2 (To COM)
Channel 2 (To N/O Contact)
2nd GATE OPERATOR or DOOR OPENER
1st GATE OPERATOR or DOOR OPENER
8 to 24 VOLT AC/DC
POWER SUPPLY
RED WIRE to POSITIVE
BLACK WIRE to NEGATIVE
RED
BLACK
GREEN
BLUE
BROWN
YELLOW
Designed to work with most brands of gate and
door openers.
Printed in China for GTO - Gates That Open, LLC
rev-090810
Programming the Receiver
Wiring Receiver to Common Gate and Door Openers
Wiring Receiver to GTO DC Operators
Wiring Receiver to GTO GP-SL100 & GP-SW100 Operators
Programmingtransmitter(s)orotheraccessdevicestoRB709U-NBreceiver:
• Pressandholdthetransmitter(device)buttontobelearned.
• Pressthe‘LEARNCH1’(or‘LEARNCH2’)buttonontheRB709U-NBreceiver
for1-2secondsoruntiltheredLEDturnson,thenreleasethebutton.
• Note:Whenthecorrectcodeisreceivedandthecorrespondingrelayoutput
isactivated,theredLEDwillturnon.
Channel 1 (GREEN WIRE to COM)
Channel 1 (BLUE WIRE to CYCLE)
BLACK
RED
Channel 2 (BROWN WIRE to COM)
Channel 2 (YELLOW WIRE to N/O Contact)
ALARM
ACC. POWER DUAL CABLE
+12Vdc
COM
DUAL LINK
LINK COM
RELAY OUTPUTS
LOCK N.C.
LOCK COM
LOCK N.O.
RUN 1
RUN 2
CLOSED 1
CLOSED 2
CYCLE
SAFETY
OPEN EDGE
RUN 2
OPEN
CLOSE
STOP
COM
COM
COM
SHADOW
LOOP
Check operation after programming:
• PressTransmitter(device)button,#1-REDLEDblinksoncetoconrm.
• PressTransmitter(device)button,#2-REDLEDblinkstwicetoconrm.
GTOGP-SL100andGP-SW100ContolBoard
TypicalGTODCpoweredgateoperators.
GTO2000XL,3000XL.4000XL,andMightyMule500
6 5 4 3 2 1
Genie Garage Door Opener
CHANNEL 1 (COM)
CHANNEL 1 (N/O)
Linear Garage Door Opener
PUSHBUTTON
COMMON
BEAM
ANTENNA
CHANNEL 1 (COM)
CHANNEL 1 (N/O)
Lift Master
Garage Door Opener
CHANNEL 1 (COM)
CHANNEL 1 (N/O)
Chamberlin
Garage Door Opener
CHANNEL 1 (COM)
CHANNEL 1 (N/O)
Lift Master SL580 Gate Opener
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
CHANNEL 1 (COM)
CHANNEL 1 (N/O)
CHANNEL 1 (N/O)
CHANNEL 2 (N/O)
CHANNEL 1 (COM)
CHANNEL 2 (COM)
RED WIRE to POSITIVE POWER
BLACK WIRE to NEGATIVE POWER
BATTERY or
TRANSFORMER
SURGE PROTECTOR
(RB570 or R4215)
Channel 1 (GREEN WIRE to COM)
Channel 1 (BLUE WIRE to CYCLE/CLOSE)
BLACK
RED
Channel 2 (YELLOW WIRE to COM)
Channel 2 (BROWN WIRE to N/O Contact)
GRN BLK RED
RECEIVER
COM COM
CYCLE
CLOSE
SAFETY
EXIT
OPEN
SHADOW
LOOP
CLOSE
EDGE
OPEN
EDGE
J11
J8
J12
8 to 24 VOLT AC/DC
POWER SUPPLY or BATTERY
RED WIRE to POSITIVE
BLACK WIRE to NEGATIVE
BATTERY or
TRANSFORMER
SURGE PROTECTOR
(RB570 or R4215)
GTO•3121HartseldRoad•Tallahassee,Florida32303•GTOSales1-800-543-4283•TechnicalSupport1-800-543-1236•www.gtoaccess.com
Connects to most garage
door openers the same
as a remote push button.
  • Page 1 1
  • Page 2 2

Genie RB709U-NB User manual

Genie
Brand
Genie
Model
RB709U-NB
Category
Garage Door Opener
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents