Black & Decker CST1200 Owner's manual

CORDLESS 12 VOLT TRIMMER

iNSTRUCTiON MANUAL

Date Code:

IVlodel Number CST1200

PLEASE READ BEFORE RETURNING

THIS PRODUCT FOR ANY REASON:

If you have a question or experience a problem with your

Black & Decker purchase, go to

WWW.BLACKANDDECKER.COM/INSTANTANSWERS

for instant answers24 hours a day.

If you can't find the answer or do not have access to the internet,

call 1-800-544-6986from 8 a.m. to 5 p.m. EST Mon. - Fri

to speak with an agent.

Please have the catalog number availablewhen you call.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

VEA EL ESPAI_OL EN LA CONTRAPORTADA.

POUR LE FRAN(_AIS, VOIR LA COUVERTURE ARRI#RE.

IN.STRUCTIVO DE O.PERACION, CENTROS DE SERVICIO Y

POLIZA DE GARANTIA. ADVERTENCIA: LEASE ESTE

INSTRUCTIVO ANTES DE USAR EL PRODUCTO.

KEY INFORMATION YOU SHOULD KNOW:

• Charge battery for a minimum of 24 hours before using your

trimmer, using the Black and Decker 12V charger 244374.

• The guard must be installed before trimming - if not, the

motor will overheat, and void your warranty.

• To operate the trimmer, the lock off button must first be

pulled back, so the trigger can be activated.

• When replacing the line, use only 0.065 in. diameter

- otherwise the unit may not function properly.

o For trouble free feeding and best results, only use

Black & Decker replacement spools with single 0.065 inch

line. Black & Decker replacement spool model number

AF-100.

Safety Guidelines - Definitions ................................................. 2

Important Safety Warnings and Instructions ............................ 2

General Safety Warnings and Instructions for all Tools ........... 3

Additional Important Safety Instructions .................................. 4

Components ............................................................................. 4

Assembly Instructions .............................................................. 5

Operation Instructions .............................................................. 6

Maintenance ............................................................................ 9

Accessories .............................................................................. 9

Troubleshooting ....................................................................... 10

Service Information .................................................................. 10

Two-Year Home Use Warranty ................................................. 10

SAFETY GUIDELINES - DEFINITIONS

It is important foryou to read and understand this manual. The

information it coniains relates to protecting YOUR SAFETY and

PREVENTING PROBLEMS. The symbols below are used to help you

recognize this information.

z_ DANGER: Indicates an imminent!y hazardous situation which,

if not avoided, will result in death or serious injury.

z_ WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

Z_CAUTION: Indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

NOTICE: Used without the safety alert symbol indicates a

potentially hazardous situation which, if not avoided, may result in

property damage.

/_WARNING: When using electric gardening appliances, basic

safety precautions should always be followed to reduce risk of fire,

e!ectric shock, and personal injury, including the following.

/!k,WARNING: Some dust created by this product contains

chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm. Some examples of these

chemicals are: • compounds in fertilizers

• compounds in insecticides, herbicides and

pesticides

• arsenic and chromium from chemically treated

lumber

To reduce your exposure to these chemicals, wear approved safety

equipment such as dust masks that are specially designed to filter

out microscopic particles.

ZLWARNING: This product contains chemicals, including lead,

known to the State of California to cause cancer, and birth defects or

other reproductive harm. Wash hands after handling.

Z_ CAUTION: Wear appropriate personal hearing protection

during use. Under some conditions and duration of use, noise from

this product may contribute to hearing loss.

READ ALL INSTRUCTIONS

TO REDUCE RiSK OF INJURY:

• Before any use, be sure everyone using this toot reads and

understands all safety instructions and other information

contained in this manual.

• Save these instructions and review frequently prior to use and in

instructing others.

• ALWAYSWEAREYEPROTECTION- Wearsafetyglassesor

gogglesatalltimeswhenthisapplianceisinuse.Safetyglasses

areavailableatextracostatyourlocalBlack&DeckerService

Centerorauthorizedservicefacility.Alwaysusefaceordustmask

ifoperationisdusty.

• GUARD- Donotusethisappliancewithoutguardproperlyattached.

• DRESSPROPERLY- Donotwearlooseclothingorjewelry.They

canbecaughtinmovingparts.Rubberglovesandsubstantial

rubbersoledfootweararerecommendedwhenworkingoutdoors.

Don'toperatetheappliancewhenbarefootorwearingopen

sandals.Weartongpantstoprotectyourlegs.Wearprotectivehair

coveringtocontainlonghair.

• NYLON LINE- Keep face, hands and feet clear of rotating cutting

line at all times.

• THE ROTATING LINE PERFORMS A CUTTING FUNCTION -

Use care when trimming around screens, fences and desirable

plantings.

• KEEP CHILDREN AWAY- All visitors should be kept at safe

distance from work area.

• IMPORTANT WARNING - When being used stones, pieces of

metal and other objects can be thrown out at high speed by the line.

The tool and guard are designed to reduce the danger. However,

the following special precautions should be taken:

z_WARNING: Make sure that other persons and pets are at least

100 ft. (30.5m) away.

Z_WARNING: To reduce the risk of rebound (ricochet) injury, work

going away from any nearby solid object such as awall, steps, large

stone, tree, etc. Use great care when working close to solid objects,

and, where necessary, do trimming by hand.

• AVOID ACCIDENTALLY STARTING - Don't carry appliance with

finger on trigger.

• DO NOT FORCE THE APPLIANCE - Itwill do the job better and

with less likelihood of a risk of injury at the rate for which it was

designed.

• USE THE RIGHT APPLIANCE - Do not use this appliance for any

job except that for which it is intended.

• DON'T OVERREACH - Keep proper footing and balance at all

times.

• DAMAGE TO APPLIANCE - Ifyou strike or become entangled

with a foreign object, stop toot immediately, check for damage and

have any damage repaired before further operation is attempted.

Do not operate with a broken hub or spool.

• AVOID DANGEROUS ENVIRONMENTAL CONDITIONS - Do not

use electric appliances in damp or wet locations. Don't use the

appliance in the rain.

• DO NOT OPERATE trimmer/edgers in gaseous or explosive

atmospheres. Motors in these appliances normally spark, and the

sparks might ignite fumes.

• STORE IDLE APPLIANCES INDOORS - When not in use,

appliances should be stored indoors in a dry locked-up place out of

reach of children.

• STAY ALERT- Watch what you are doing. Use common sense. Do

not operate appliance when you are tired.

• MAINTAIN APPLIANCES WITH CARE - Keep cutting edge sharp

and clean for best performance and to reduce the risk of injury.

Follow instructions for lubricating and changing accessories.

Inspect appliance cord periodically, and if damaged, have it

repaired by an authorized service facility. Inspect extension cords

periodically and replace if damaged. Keep handles dry, clean, and

free from oil and grease.

• CHECK DAMAGED PARTS - Check for alignment of moving

parts, binding of moving parts, breakage of parts, mounting, and

any other condition that may affect its operation. Before further use

of the appliance, a guard or other part that is damaged should be

repaired or replaced by an authorized service center unless otherwise

indicated elsewhere in this manual.

• FOR HOUSEHOLD use only.

KEEPGUARDSIN PLACE AND IN WORKING ORDER.

KEEP HANDS AND FEET AWAY FROM CUTTING AREA.

DO NOT CHARGE APPLIANCE IN RAIN OR IN WET

LOCATIONS.

SAVE THESE iNSTRUCTiONS

• Do not use battery for anything other than with this product or other

designated Black & Decker product, out microscopic particles.

Z_WARNiNG: When using electric tools, basic safety recautions

should always be followed to reduce risk of fire, electric shock, and

personal injury, including the following:

• Do not incinerate the battery even if it is severely damaged or is

completely worn out. The battery can explode in a fire. Check with

local codes for possible special disposal instructions.

• Ifany leakage of liquid from the battery cells occurs, discontinue

use immediately and return the battery to your local Black &

Decker Service Center or authorized service facility.

• Never attempt to open the battery for any reason. Ifthe plastic

housing of the battery breaks or cracks, immediately discontinue

use and do not recharge.

• Do not charge appliance in rain or in wet locations.

• Use only the following type and size battery: Black & Decker

244373 - 12V.

• Use only Black and Decker 12V charger 244374.

• Exercise care in handling batteries in order not to short the battery

with conducting materials such as rings, bracelets and keys. The

battery or conductor may overheat and cause burns.

• Do not open or mutilate the battery. Released electrolyte is

corrosive and may cause damage to the eyes or skin. It may be

toxic if swallowed.

• Ifthe battery case cracks due to a fall or other impact and the

electrolyte gel leaks out, wipe it up with a cloth, neutralize the acid

with any alkaline substance such as ammonia solution or baking

soda. If the electrolyte gets on your skin, immediately flush with

water and consult a doctor.

6

1. Trigger 5. Guard

2. Charger LED 6. Charger

3. Air Intake 7. Hub & Spool

4. Lock-Off 8. Charger Bracket

BeforeassemblingyourCordlessStringTrimmer,checkthatyou

havereceivedthefollowingintheshippingcarton.

SeeFigure1.

A. Trimmer/Edger.

B.Guard.

C.ChargerandChargerBracket.

D.HardwareBagwith(2)screwsand(2)plasticanchors.

/_ WARNING: The guard must always be on the toot to protect the

user. Use of the unit without the guard will overheat the motor, and

void the warranty.

NEVER OPERATE TOOL WITHOUT GUARD FIRMLY IN PLACE.

1. Position the open center of the guard m_,

over the line feed head (Figure 2).

2. Hinge the guard on the hook located

on the lower motor housing. Ensure

the line is free, and not tucked under

the guard. Once hooked, lightly pull

on the back edge of the guard and

push the guard down until the 2

latches snap into place on the motor

housing. (Figure 2)

3. Using a phillips screwdriver, screw the

preassembted screw in the guard, into

the motor housing. (Figure 3)

BATTERY

THE LEAD ACiD BATTERY FOR YOUR TRIMMER IS ONLY

PARTIALLY CHARGED AT THE FACTORY. BEFORE USING

YOUR TRIMMER, THE BATTERY MUST BE CHARGED FOR A

MINIMUM OF 24 HOURS.

• Your trimmer is equipped with a charger bracket that may be

mounted firmly to a walt in your garage, shed or similar building.

(Hardware for hanging the bracket is included in the plastic bag

packed with the trimmer.) Charging your battery in this bracket is

very convenient because it hangs the tool up, out of the way and

ensures a good, solid contact between the charging terminals.

MOUNTINGTHE CHARGER BRACKET (FIGURE 4)

1. If you intend to mount the

charger bracket on a wall,

follow the instructions _"_

listed below. _

2. Use the hardware

provided (Figure 1D) only

if hanging on conventional

hollow wall construction

such as drywall over studs.

If not, use the appropriate |il_j

fasteners for the particular "3

wall material.

3. Use the charger bracket / / Chargingport and pin

to mark the locations of Orifice dechargement et

the holes required. Be tige

sure to mount the bracket / Puertoy punta decarga

high enough so that the

trimmer can hang freely

from it; about 4 feet (1.2m)

from the floor and close

enough to an electrical

outlet to plug-in charging

transformer.

4. a) Conventional hollow wall: Drill a .250 in. (6mm) diameter

hole at each marked location. Insert the plastic anchors supplied

into the holes and insert one of the screws into each anchor.

4. b) Alternative wall materials: Insert fasteners as appropriate

making sure screw heads are small enough to fit through bracket.

5. Tighten the screws until the heads are above the walt just

enough so that the charger bracket will fit between the wall and

the screw head.

6. Place the charger bracket on the wall (hook end up) and make

sure that the power cord is positioned in the side slot. Press the

charger bracket over the screw heads and slide it down until it

sits firmly on the screws.

7. Firmly tighten both screws.

LED INDICATOR LIGHT

The unit is equipped with a red LED charging indicator light, located

on the upper left side of the unit (Figure 1). The indicator light will

come on when the unit is properly connected to the charging base

and the power plug is inserted into the electrical outlet. The light will

remain on, so long as the unit is properly connected to the powered

charging base. It is recommended to store the unit on the charger

during the growing season, with the charger plugged in, to have the

battery charged for the next use.

TO CHARGE YOUR BATTERY, FOLLOW THE STEPS BELOW

1. Install the trimmer onto the charger bracket by positioning the

handle cavity, shown in Figure 4 over the hook of the charger

bracket.

2. Rotate the trimmer down, keeping the hook engaged with the

handle cavity, and position the charge port over the bracket's

charge pin (Figure 4).

3. Plug the charger into any standard 120 volt, 60Hz outlet.

Charging wilt be automatically controlled until you remove the

trimmer from the bracket.

4. It is recommended that the trimmer be left on charge, during the

growing season. For winter or other extended periods of

storage, it is recommended that the unit be fully charged prior to

storage.

z_ CAUTION: ALWAYS WEAR EYE PROTECTION.

/_ CAUTION: Inspect area to be trimmed and remove any wire,

cord, or string-like objects which could become entangled in the

rotating line or spool. Be particularly careful to avoid any wire which

might be bent outwardly into the path of the tool, such as barbs at the

base of a chain link fence.

OPERATETHETRIMMER/EDGER

• To turn trimmer on, pull the lock out button, shown in Figure 1,

backwards and, then squeeze the trigger switch. To turn the

tool off, release the trigger.

• Slowly swing trimmer side-to-side as _'_

shown in Figure 5.

To convert for maintenance edging,

turn off the tool. (See Figure 6)

Holding the trimmer with one hand by

the auxiliary handle, grasp the trimmer

head collar and push in direction of

arrow and rotate the trimmer head

clockwise (when viewed from the

switch end) until it stops, (half turn),

release your hand. The tool is locked in

the edger position.

Rotate the wire edge guide

forward and down into place

before edging, as shown

inFigure7.

• To operate as a maintenance A

edger, position trimmer above

sidewalk as shown in Figure 8.

• Return to trimming position by

turning the toot off, push in

direction of arrow and rotating

the trimmer head counter

clockwise until it stops. When

using the tool in the trimmer

mode you may choose to fold

the wire edge guide up out of

the way.

CUTTING LINE

LINE FEEDING

Your trimmer uses .065 in. (1.65 ram) diameter, ROUND nylon

line to cut grass and weeds quickly and easily. During use, the tip

of the nylon tine witl become frayed and worn and the special self

feeding line hub will automatically feed and trim a fresh length of

line. Cutting line wilt wear faster and require more feeding if the

cutting or edging is done atong sidewalks or other abrasive

surfaces or heavier weeds are being cut. The advanced

automatic tine feeding mechanism senses when more cutting line

is needed and feeds and trims the correct length of line

whenever its required. DO NOT BUMP unit on ground in attempt

to feed line or for any other purposes.

CLEARINGJAMSANDTANGLEDLINES

Fromtimetotime,especiallywhencuttingthickorstalkyweeds,

thelinefeedinghubmaybecomecloggedwithsaporother

materialandthelinewiltbecomejammedasaresult.Toclear

thejam,followthestepslistedbelow.

1.Pressthereleasetabsontheline

hubcap,asshowninFigure9

andremovethecapbypullingit

straightoff.

2.Liftthespoolofnylonlineoutof

thehubandclearanybrokenline

orcuttingdebrisfromthespool

area.(Ifyouplantoreplacethe

spoolorrewindit,thisistheplace

todoso,otherwise,moveon.)

3.Unwrapaboutonefoot(30cm)of

linetoensurethatit'sundamaged.

IfitisOKrewinditandinsertthe

lineendthroughtheeyeletinthe

spoolhubasshowninFigure10.

Pull4in.(10cm)oftheline

throughtheholeandmaintain

tensionwhileplacingthespool

downintothehubwiththearrow

up,asshowninFigure11.

4.PressthespooldownGENTLY

androtateituntilyoufeetitdrop

intoplace.(Wheninplace,the

spoolwillturnafewdegreesleft

andrightfreely).Takecareto

keepthelinefrombecoming

trappedunderthespool.

5.Snapthehubcapbackon,and

powerthetooton.Inafewsecondsorlessyou'llhearthenylon

linebeingcutautomaticallytotheproperlength.

• For trouble free feeding and best results, only use

Black & Decker replacement spools with single 0.065 inch line.

Black & Decker replacement spool model number AF=100.

SPOOL OR LINE REPLACEMENT (Use .065 in. (1.65mm)

diameter ROUND line only)

1. Perform step 1 above to remove cap.

2. Remove the spool from the tool and remove and discard all line

on the spool.

3. Choose either OPTION 1 or OPTION 2 below for spool or line

replacement. Perform steps listed under Option 1or Option 2,

then continue with steps 4 through 6 below.

4. Insert the line end through the eyelet in the spool hub, as shown

in Figure 10. Pull the line through the hole to maintain tension

while placing the spool down into the hub, as shown in

Figure 11.

5. Press the spool down GENTLY and rotate it until you feel it drop

into place. (When in place, the spool will turn a few degrees left

and right freely). Take care to keep the line from becoming trapped

under the spool.

6.Snapthehubcapbackon,andpowerthetooton.Inafew

secondsorlessyou'llhearthenylonlinebeingcutautomatically

totheproperlength.

OPTION1:ACCESSORYREPLACEMENTSPOOL

UseBlack&DeckerreplacementspoolModelNo.AF-100.Discard

oldspool.

OPTION2: REWINDINGSPOOLUSINGBULKLINE

Bulklineforyourtrimmer/edgerisavailableatextra cost from your

local dealer or Black & Decker Service Center. To install bulk line,

follow the steps below. (Use .065 in. diameter ROUND line only)

1. Insert one end of the bulk line into

the hole in the spool as shown

in Figure 12 about 1/2 in. (12 mm).

2. Hold the line in the hole and pull

the rest of the line through the slot

in the spool, shown in Figure 12.

3. Snugly and evenly wind the bulk

line onto the spool in the direction

of the arrow on the spool until the

line builds up to the notches in the

spool rim. (Figure 12) Do not

overfill spool. The spool holds

30 feet (10 m) of line.

1. Keep the air intake slots (Figure 1) clean to avoid overheating.

2. Your trimmer line can dry out over time. To keep your line in top

condition, store spare pre-wound spools or bulk line in a plastic,

sealable bag with a tablespoon of water.

3. Plastic parts may be cleaned by using a mild soap and a damp

rag.

4. DO NOT immerse tool in water or squirt it with a hose. DO NOT

allow any liquid to get inside it.

5. Do not store the toot on or adjacent to fertilizers, gasoline, or

other chemicals.

6. DO NOT clean with a pressure washer.

7. The line cutter on the edge of the guard can dull over time. It is

recommended you periodically touch-up the sharpness of the

blade with a file.

iMPORTANT: To assure product SAFETY and RELIABILITY,

repairs, maintenance and adjustment should be performed by

authorized service centers or other qualified service organizations,

always using identical replacement parts.

Use Black & Decker replacement spool Model No. AF-100.

Reload nylon line (either bulk or prewound replacement spool) as

shown in this manual.

• USE ONLY .065 in. (1.65 mm) DIAMETER NYLON

MONOFILAMENT LINE. Do not use

serrated or heavier gauge line, as they will overload the motor and

cause overheating. The unit only functions properly with 0.065 in.

diameter nylon monofilament line. This line is available at your

local dealer or authorized service center.

/_WARNING: The use of any accessory not recommended by

Black & Decker for use with this tool could be hazardous.

Problem

• Unit won't run.

• Line won't feed.

• Line fails to cut

off.

Possible Cause

Battery not charged.

Line tangled in spool.

Line cutter in guard is

damaged or missing.

Line extends past

guard.

Possible Solution

• Charge for at least

12 hours

• Unwrap 24 in. of line

and rewind.

• Return to service

centre for replacement/

repair.

• Rewind or trim line to

line cutter.

For assistance, visit our website www.blackanddecker.com for

the location of the service center nearest you or call the

BLACK & DECKER help line at 1=800=544=6986.

All Black & Decker Service Centers are staffed with trained personnel

to provide customers with efficient and reliable power tool service.

Whether you need technical advice, repair, or genuine factory

replacement parts, contact the Black & Decker location nearest you.

Tofind your local service location, refer to the yellow page directory

under "Toots--Electric" or call: 1=800=544=6986 or visit

www.blackanddecker.com.

may be required. Please check with the retailer for their specific

return policy regarding returns that are beyond the time set for

exchanges.

The second option is to take or send the product (prepaid) to a

Black & Decker owned or authorized Service Center for repair or

replacement at our option. Proof of purchase may be required.

Black & Decker owned and authorized Service Centers are listed

under "Toots-Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you

specific legal rights and you may have other rights which vary from

state to state or province to province. Should you have any questions,

contact the manager of your nearest Black & Decker Service Center.

This product is not intended for commercial use.

LATIN AMERICA: This warranty does not apply to products sold in

Latin America. For products sold in Latin America, check country

specific warranty information contained in the packaging, call the local

company or see the website for warranty information.

FREE WARNING LABEL REPLACEMENT: Ifyour warning labels

become illegible or are missing, call 1=800=544=6986 for a free

replacement.

Black & Decker (U.S.) Inc. warrants this product for two years against

any defects in material or workmanship. The defective product will be

replaced or repaired at no charge in either of two ways.

The first is to return the product to the retailer from whom it was

purchased (provided that the store is a participating retailer). Returns

should be made within the time period of the retailer's policy for

exchanges (usually 30 to 90 days after the sale). Proof of purchase

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

10

See 'Tools=Electric'

- Yellow Pages -

for Service & Sales

Page is loading ...

• GARANT{A BLACK & DECKER • BLACK & DECKER WARRANTY

, SOLAMENTE PARA PROPOSITOS DE MEXICO

Distributor Name. Sello firma del distribuidor

Date of purchase. Fecha de compra Invoice No. •No. de factura

PRODUCT INFOMATION • IDENTIFICACION DEL PRODUCTO

Cat. No.. Catalogo 6 Modelo Serial Number. No. de serie

Name. Nombre Last Name •Apellido

Address. Direcci6n

City. Ciudad State •Estado

Postal Code. C6digo Postal Country •Pais

Telephone. No. Tel_fono

3O

Page is loading ...

Cat No. CST1200

Form No. 90572709

32

MARCH 2011

Printed in China

Black & Decker CST1200 Owner's manual

This manual is also suitable for

Black & Decker CST1200 Owner's manual

in other languages

Related papers

Other documents