Peerless SUF640P User manual

Installation and Assembly:

Peerless Ultra-Thin Flat Mount for 23" to 46" (58 - 117 cm)*

LCD Flat Panel Screens

Model: SUF640P

*Screen Compatability Requirements

• The depth of this mount (0.33") may not provide sufﬁcient space for

proper ventilation on some screens. Please refer to the manufacturer's

requirements for mounting your screen before installation.

• The screen must have a ﬂat mounting surface, or the mounting holes

need to be on the furthest back surface of the screen.

• Input/Output connection must be properly oriented to accomodate

mounting 0.33" from the wall.

ISSUED: 05-29-08 SHEET #: 202-9281-7 12-14-09

Max UL Load Capacity: 150 lb (68kg)

©

U

L

USC

I

D

:

0

1

8

7

6

2

3215 W. North Ave. • Melrose Park, IL • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com

2 of 34

ISSUED: 05-29-08 SHEET #: 202-9281-7 12-14-09

NOTE: Read entire instruction sheet before you start installation and assembly.

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to Wood Stud Wall ................................................................................................................................................4

Installation to Solid Concrete/Cinder Block walls ...................................................................................................................5

Installing Adapter Brackets .....................................................................................................................................................6

Mounting and Removing Flat Panel Screen ...........................................................................................................................8

Tools Needed for Assembly

• stud ﬁnder ("edge to edge" stud ﬁnder is recommended)

• drill

• 5/16" (8 mm) bit for concrete and cinder block wall

• 5/32" (4 mm) bit for wood stud wall

• level

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• This mount is designed to attach the screen 0.33" from the wall. Please refer to manufacturer's installation guide

recommendations for required distance from wall to avoid risk of injury or property damage.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum UL Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud ﬁnder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws ﬁrmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal

injury.

• This product was designed to be installed on the following wall construction only;

WALL CONSTRUCTION HARDWARE REQUIRED

• Wood Stud Included

• Wood Beam Included

• Solid Concrete Included

• Cinder Block Included

• Metal Stud Do not attach except with Peerless Metal Stud Accessory Kit

- ACC215; (not evaluated by UL)

• Brick Contact Qualiﬁed Professional (not evaluated by UL)

• Other or unsure? Contact Qualiﬁed Professional

WARNING

3 of 34

ISSUED: 05-29-08 SHEET #: 202-9281-7 12-14-09

C

A

B

D

Description Qty. Part #

A

wall plate 1 046-P1030

B

adapter bracket 2 046-P1130

C

wood screws 2 500-1090

D

concrete anchors 2 590-0320

E

M5 x 12 mm hex screw

4

560-1732

F

M5 x 25 mm hex screw

4

560-1733

G

M6 x 12 mm hex screw

4

560-1734

H

M6 x 25 mm hex screw

4

560-1735

I

.725" washer

4

540-9478

J

.75" spacer

4

540-1059

K

4 mm security driver

1

560-1133

L

4 mm security allen wrench

1

560-9646

M

M8 x 12 mm hex screw

4

560-1736

N

M8 x 25 mm hex screw

4

560-1737

Parts List

E

F

G

H

I

J

K

Before you begin, make sure all parts shown are included with your product.

Parts may appear slightly different than illustrated.

M

N

L

4 of 34

ISSUED: 05-29-08 SHEET #: 202-9281-7 12-14-09

Installation to Wood Stud Wall

Wall plate (A) can be mounted to two studs that are 16" apart. Use a stud ﬁnder to locate the edges of the studs.

Use of an edge-to-edge stud ﬁnder is highly recommended. Based on their edges, draw a vertical line down each

stud’s center. Place wall plate on wall as a template. The mounting slots should be located 7" (177 mm) above the

desired screen center as shown in ﬁgure 1.1. Level plate, and mark the center of the two mounting holes. Make

sure that the mounting holes are on the stud centerlines. Drill two 5/32" (4 mm) dia. holes 2" (51 mm) deep. Make

sure that the wall plate is level, secure it using two wood screws (C) as shown in ﬁg. 1.2.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all

attached hardware and components.

• Tighten wood screws so that wall plate is ﬁrmly attached, but do not overtighten. Overtightening can damage the

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud ﬁnder

is highly recommended.

• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-

ers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).

WARNING

C

A

ﬁg. 1.2

ﬁg. 1.1

CENTER OF SCREEN

A

STUD

7"

(177 mm)

NOTE: If mounting with in-wall box model IBA1 (not UL listed), allow bottom edge

of wall plate (A) to touch top edge of in-wall box as shown below.

A

IN-WALL BOX

DRYWALL

A

IN-WALL BOX

WOOD STUD

1

5 of 34

ISSUED: 05-29-08 SHEET #: 202-9281-7 12-14-09

Installation to Solid Concrete or Cinder Block

Make sure that wall plate (A) is level, use it as

a template to mark two mounting holes. The top

mounting slots should be located 7" (177 mm) above

the desired screen center as shown in ﬁgure 1.1

on page 4. Drill four 5/16" (8 mm) dia. holes to a

minimum depth of 2.5" (64 mm). Insert anchors (D) in

holes ﬂush with wall as shown (right). Place wall plate

over anchors and secure with two wood screws (C).

Level, then tighten all fasteners.

• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete

thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid

part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 speciﬁca-

tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to

avoid breaking out the back of the hole when entering a void or cavity.

• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.

• Installer must verify that the supporting surface will safely support the combined load of the equipment and all at-

tached hardware and components.

WARNING

• Tighten screws so that wall plate is ﬁrmly attached,

but do not overtighten. Overtightening can damage

screws, greatly reducing their holding power.

• Never tighten in excess of 80 in. • lb (9 N.M.).

• Always attach concrete anchors directly to load-

bearing concrete.

• Never attach concrete anchors to concrete covered

with plaster, drywall, or other ﬁnishing material.

If mounting to concrete surfaces covered with a

ﬁnishing surface is unavoidable (not evaluated by

UL), the ﬁnishing surface must be counterbored

as shown below. Be sure concrete anchors do not

pull away from concrete when tightening screws. If

plaster/drywall is thicker than 5/8", custom fasteners

must be supplied by installer (not evaluated by UL).

WARNING

C

A

D

SOLID CONCRETE

CINDER BLOCK

1

CUTAWAY VIEW

INCORRECT CORRECT

wall

plate

wall

plate

plaster/

dry wall

plaster/

dry wall

concrete

1

3

2

D

Drill holes and insert anchors (D).

Place plate (A) over anchors (D) and secure with screws (C).

Tighten all fasteners.

A

K

D

C

concrete

surface

6 of 34

ISSUED: 05-29-08 SHEET #: 202-9281-7 12-14-09

Installing Adapter Brackets

To prevent scratching the screen, set a cloth on a ﬂat, level surface that will support the weight of the screen. Place

screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.

Place adapter brackets (B) on back of screen, align to holes, and center on back of screen as shown below. Attach

the adapter brackets to the back of the screen using the appropriate combination of screws, washers, and spacers

as shown in steps 2-1 or 2-2.

NOTE: Top and bottom holes of screen must always be used.

Verify that all holes are properly aligned, and then tighten screws using allen wrench (L).

• Tighten screws so adapter brackets are ﬁrmly attached. Do not tighten with excessive force. Overtightening can

cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become

detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly

secured, damage may occur to screen or product may fail.

WARNING

CENTER BRACKETS

VERTICALLY

ON BACK OF

SCREEN

NOTE: "X" dimensions should be equal.

NOTE: For ﬂat back screens proceed to step 2-1. For bump-out or recessed back screen skip to step 2-2.

2

B

7 of 34

ISSUED: 05-29-08 SHEET #: 202-9281-7 12-14-09

Begin with the shortest length screw, hand thread through washer and adapter bracket into screen as shown below.

Screw must make at least three full turns into the mounting hole and ﬁt snug into place. Do not over tighten. If screw

cannot make three full turns into the screen, select a longer length screw from the bafﬂed fastener pack. Repeat for

remaining mounting holes, level brackets and tighten screws.

NOTE: Spacers may not be used, depending upon the type of screen.

NOTE: If screen manufacturer's requirements state that more than 0.33" of ventilation is required, spacers may be

used to add an additional 0.5" of space between the wall and the screen as shown right.

Begin with longer length screw, hand thread through washer, adapter bracket and spacer in that order into screen

as shown below. Screw must make at least three full turns into the mounting hole and ﬁt snug into place. Do not

over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the bafﬂed

fastener pack. Repeat for remaining mounting holes, level brackets and tighten screws.

For Flat Back Screen

For Bump-out or Recessed Back Screen

SCREEN

SCREW

ADAPTER

BRACKET (B)

2-2

2-1

If you have any questions, please call Peerless customer care at 1-800-865-2112.

SCREEN

WASHER (I)

SCREW

ADAPTER

BRACKET (B)

SPACER (J)

ADAPTER

BRACKET (B)

SCREEN

WASHER (I)

SCREW

8 of 34

ISSUED: 05-29-08 SHEET #: 202-9281-7 12-14-09

DETAIL 1

WALL

VELCRO

Guide hooks of adapter brackets (B) onto

ﬂange of wall plate (A). Then slowly swing

screen toward wall as shown in ﬁg. 3.1.

Gently press on screen to ensure velcro

strips are engaged as shown in detail 1.

To horizontally adjust screen, swing screen

away from mount to disengage velcro, and

slide screen along wall plate to desired

position as shown in ﬁg 3.2. Then slowly

swing screen toward wall to re-engage

velcro.

To remove screen from mount, swing

screen away from mount, and lift screen off

of mount.

Mounting and Removing Flat Panel Screen

• Always use an assistant or mechanical lifting equipment to safely lift and position the ﬂat panel screens.

WARNING

3

ﬁg. 3.2

ﬁg. 3.1

WALL WALL

SCREEN

A

B

A

B

All other brand and product names are trademarks or registered trademarks of their respective owners.

Peerless Industries, Inc.

3215 W. North Ave.

Melrose Park, IL 60160

www.peerlessmounts.com

Page is loading ...

33 of 34

ISSUED: 05-29-08 SHEET #: 202-9281-6 12-01-09

Peerless Industries, Inc. establishes a warranty period of ﬁve years for products manufactured or supplied by Peerless. This period commences from the date of

sale of the product to the original consumer, but will in no case last for more than six years after the date of the product’s manufacture. During the warranty period

such products will be free from defects in material and workmanship, provided they are installed and used in compliance with the instructions established by

Peerless Industries, Inc. Subject to applicable legal requirements, during the warranty period Peerless will repair or replace, or refund the purchase price of, any

such product which fails to conform with this warranty.

Any other warranties prescribed by the law which may apply with respect to such products also are limited in duration to the warranty period speciﬁed in this

Limited Five-Year Warranty.

This warranty does not cover damage caused by (a) service or repairs by the customer or a person who is not authorized for such service or repairs by Peerless

Industries, Inc., (b) the failure to utilize proper packing when returning the product, (c) incorrect installation or the failure to follow Peerless’ instructions or warnings

when installing, using or storing the product, or (d) misuse or accident, in transit or otherwise, including in cases of third party actions and force majeure.

In no event shall Peerless be liable for incidental or consequential damages or damages arising from the theft of any product, whether or not secured by a security

device which may be included with the product.

This Limited Five-Year Warranty is in lieu of all other warranties, expressed or implied, and is the sole remedy with respect to product defects. No retailer, dealer,

distributor, installer or other person is authorized to modify or extend this warranty or impose any obligation on Peerless in connection with the sale of any product

manufactured or supplied by Peerless.

This warranty gives speciﬁc legal rights, and you may also have other rights provided by the national legislation of the country in which you purchased such

product.

LIMITED FIVE-YEAR WARRANTY

Español

www.peerlessmounts.com

Peerless Industries, Inc. establece un período de garantía de cinco años para los productos fabricados o suministrados por Peerless. Este período empieza en

la fecha de venta del producto al consumidor original, pero en ningún caso durará más de seis años después de la fecha de fabricación del producto. Durante

la vigencia de la garantía, dichos productos se encontrarán libres de defectos en sus materiales y fabricación, siempre que se instalen y usen de conformidad

con las instrucciones establecidas por Peerless Industries, Inc. Sujeto a los requisitos legales pertinentes, durante la vigencia de la garantía Peerless reparará o

reemplazará un producto que no cumpla con la presente garantía o reembolsará el precio de compra del mismo.

Cualquier otra garantía exigida por ley que podría ser aplicable con respecto a dichos productos también tendrá una vigencia limitada al período de garantía

especiﬁcado en la presente Garantía Limitada de Cinco Años.

La presente garantía no abarca los daños causados por (a) trabajos de servicio, mantenimiento o reparación hechos por el cliente o una persona que no está

autorizada por Peerless Industries, Inc. para realizar esos trabajos, (b) no utilizar un embalaje apropiado al devolver el producto, (c) una instalación incorrecta o

no seguir las instrucciones o advertencias de Peerless al instalar, usar o almacenar el producto, o (d) uso indebido o accidente, en tránsito o de otro modo, incluso

si se trata de acciones atribuibles a terceros o de casos de fuerza mayor.

Peerless en ningún caso será responsable de daños incidentales o indirectos o daños que surjan del robo de un producto, esté o no protegido por un dispositivo

de seguridad incluido con el producto.

La presente Garantía Limitada de Cinco Años reemplaza cualquier otra garantía expresa o implícita, y es la única reparación con respecto a defectos en el

producto. Ningún comerciante minorista, agente, distribuidor, instalador u otra persona, está autorizado para modiﬁcar o prolongar la presente garantía ni para

imponer una obligación a Peerless en relación con la venta de un producto fabricado o suministrado por Peerless.

La presente garantía otorga derechos legales especíﬁcos, y usted también podría tener otros derechos en virtud de la legislación nacional del país donde usted

compró el producto.

GARANTÍA LIMITADA DE CINCO AÑOS

www.peerlessmounts.com

Page is loading ...

Peerless SUF640P User manual

This manual is also suitable for

Peerless SUF640P User manual

in other languages

Related papers

Other documents