Pacific Dualies 291608 User manual

Brand
Pacific Dualies
Model
291608
Category
Car kits
Type
User manual
7
Limited Warranty / Terms & Conditions
INSTALLATION
MANUAL
&
LIMITED LIFETIME
WARRANTY
Limited Lifetime RMA Warranty Card
Ship Post Paid To:
Pacific Dualies, Inc.
13637 Cimarron Avenue
Gardena, CA. 90249
Name: __________________
Address: ________________________________________
________________________________________
Telephone: ______________ Fax: ___________________
email: __________________________
Return Merchandise Authorization No. _______________
Part No. _________________
Pacific Dualies, Inc. warranties its stainless steel wheel simulators and
associated accessories against defects in material, finish and workman-
ship on a limited lifetime basis providing that the original owner has
properly installed and maintained the vehicle and its accessories. Pacific
Dualies is not responsible for factory wheel and rim variances. Pacific
Dualies’ warranty applies only to the original purchaser and owner of the
products being returned. Should any of the above mentioned products
lose its shine or be deemed defective, Pacific Dualies will repair or replace
the product in question, free of charge.
The warranty on defective merchandise is limited to repair or replace-
ment only of the item in question. Pacific Dualies, Inc. at our option will
repair or replace the product in question. Repairs or replacements will be
by the sole discretion of the Manufacturer. Merchandise returns will not
be accepted for any reason without prior authorization (RGA number)
from Pacific Dualies, Inc. and must be accompanied by an original receipt
or warranty claim card found in the original instruction manual. All
returned merchandise must be shipped freight prepaid to our warehouse.
This warranty does not cover any additional installation costs incurred by
the customer.
Reason For Return:
Pacific Dualies, Inc. Installation Manual & Limited Warranty
6
Pacific Dualies, Inc. Installation Manual & Limited Warranty Wheel Simulator Mounting Instructions
1
Application Guide
Steel Valve-Stem Extender Installation
Contents
Application Guide ..........................................................................................................1
Wheel Simulators Installation ................................................................................... 2
Mounting Style 1 - Bolt-On ....................................................................... 2
Mounting Style 2 - Snap-On ..................................................................... 3
Mounting Style 3 - Over Lug .................................................................... 4
Mounting Style 4 - Lug Removal ............................................................. 5
Steel Valve-Stem Extender Installation .................................................................. 6
Limited Lifetime Warranty .......................................................................................... 7
Warranty Card/Form ..................................................................................................... 7
Application Guide
SET PART #
22-2250FH
22-22551RH
22-2250FS
22-2251RS
22-2250FH5
22-2251RH5
22-2250FS5
22-2251RS5
22-2270FH
22-2271RH
22-2270FS
22-2271RS
22-2270FH5
22-2271RH5
22-2270FS5
22-2271RS5
28-1608
29-1608
30-1950
31-1608
31-1608A
32-1608
32-1950
SET PART #
32-1950A
33-1950
34-1608
35-1608
35-4608
36-4608
38-1608
38-1658
37-1950
38-1950
38-4608
38-4658
39-1608
39-1658
39-4608
39-4658
40-1950
42-1950
43-1608
43-1950
45-1608
45-1950
49-1608
MOUNTING STYLE
Style 4
Style 4
Style 4
Style 4
Style 4
Style 4
Style 4
Style 4
Style 4
Style 4
Style 4
Style 4
Style 4
Style 4
Style 4
Style 4
Style 1
Style 1
Style 1
Style 3
Style 3
Style 3
Style 3
MOUNTING STYLE
Style 3
Style 4
Style 1
Style 1
Style 1
Style 1
Style 1
Style 1
Style 4
Style 4
Style 1
Style 1
Style 1
Style 1
Style 1
Style 1
Style 3
Style 3
Style 3
Style 3
Style 4
Style 4
Style 2
Steel Valve-Stem Extender
Pacific Dualies Stainless Steel Valve-Stem Extenders are ideal for any
dually application. With the quick’n-easy valve-stem extender set up, it
makes checking and filling the inner tire “quick’n-easy!”
HAND HOLE
BRACKET
& SLOT
STEEL VALVE
EXTENDER
RETAINER
NUT
LOCK
NUT
MOUNTING
CLIP
*INSPECT VALVE-STEM EXTENSIONS EVERY SIX MONTHS*
**REPLACE VALVE-STEM EXTENSIONS WHEN DAMAGED**
! CAUTION
OUTER DUAL
TIRE
OUTER DUAL
TIRE
INNER DUAL
TIRE
43
Pacific Dualies, Inc. Installation Manual & Limited Warranty
Wheel Simulator Mounting Instructions
Mounting style designed with strong steel gripping teeth reinforced by
springs that grasp firmly onto the wheel of the vehicle holding the
simulator securely in place. Removal of (OEM) lug-nuts are not required.
Snap-On (Style 2)
Over-The-Lug Mounting Style (Style 3)
Mounting style designed with built-in jam nuts that screw over the
original equipment (OEM) studs on the wheel. Removal of (OEM) lug-nuts
are not required.
Wheel Simulator Kit Contains:
Item 1. (2) Stainless Steel Front
Wheel Simulators
Item 2. (2) Stainless Steel Rear
Wheel Simulators
Installation:
Step 1. Align either a front or rear simulator to the corresponding
(OEM) wheel.
Step 2. With a quick firm nudge, press the simulator into the (OEM)
wheel - making sure that the wheel simulator snaps securely
into place.
Step 3. Repeat Steps 1& 2 on each of the remaining (OEM) wheel
Wheel Simulator Kit Contains:
Item 1. (2) Front Wheel Covers
Item 2. (2) Rear Wheel Covers
Item 3. Lug-nut covers w/Jam-nuts.
(Qty. depending on application)
Item 4. (4) Pop-out center plates
(For Front Wheel Hub Access)
Item 5. (1) Lug-nut/Jam-nut Removal Tool
Installation:
Step 1. Begin by sliding on a front or rear wheel simulator cover onto the
vehicle wheel without removing any of the OEM lug-nuts - allowing
four of the OEM lug-nuts and studs to clear the four enlarged holes
on the wheel simulator cover.
Step 2. Carefully bolt on the Pacific Dualies lug-nut covers - securing them to
the remaining threading left on the OEM studs.
Warning - *Hand Tighten using tool provided*
Warning - **Do Not Use Impact Wrench**
Step 3. Snap on the Pop-Out Center Plates on to the center of the
corresponding wheel simulator cover.
Snap - On Mounting Style Over - The - Lug Nut Mounting Style
O
EM W
heel
O
EM W
heel
*Failure to follow all instructions could result in wheel loss, resulting in serious injury or death
**Read all instructions before beginning installation & Follow all instructions in order presented
! WARNING
*Failure to follow all instructions could result in wheel loss, resulting in serious injury or death
**Read all instructions before beginning installation & Follow all instructions in order presented
! WARNING
Item 2.
Item 3.
Item 4.
Item 2.
25
Pacific Dualies, Inc. Installation Manual & Limited Warranty Wheel Simulator Mounting Instructions
OEM Wheel
OEM Wheel
Four Lug Nut Removal Bolt On
Wheel Simulator Kit Contains:
Item 1. (2) Stainless Steel Front
Simulators
Item 2. (2) Stainless Steel Rear
Simulators
Item 3. (2-4) Pop-out Center Caps
(depending on application)
Item 4. Snap-on Lugnut covers
Installation:
Step 1. Begin by removing every “other” OEM lug nut from the wheel
application.
Step 2. Slide on either a front or rear wheel simulator cover onto the
corresponding wheel, allowing every other OEM stud to clear
the holes on the wheel simulator.
Step 3. Re-apply the removed OEM lug nuts - securely fastening the
wheel simulator to the OEM Wheel.
Step 4. Snap on the provided Pacific Dualies snap-on lugnut covers,
securing them to the OEM lugnuts that now sit above the
wheel simulator cover.
Step 5. Repeat Steps 1-4 for each of the remaining wheels.
Mounting style designed with every other lug nut removal per wheel.
Lug Nut Style (Style 4) Bolt-On Style (Style 1)
The Bolt-on mounting style is designed to bolt onto the wheel by using
the original equipment (OEM) lug-nuts.
Wheel Simulator Kit Contains:
Item 1. (2) Stainless Steel Front
Simulators
Item 2. (2) Stainless Steel Front
Center Caps
Item 3. (2) Front Retainer Rings
Item 4. (2) Stainless Steel Rear
Simulators
Installation:
Step 1. Begin by removing “all” OEM lug nuts from the wheel.
Step 2. Slide on either a front or rear wheel simulator onto the
corresponding wheel allowing the OEM studs to clear the
holes on the wheel simulator cover.
Step 3. Slide on one of the retainer rings allowing the OEM studs to
clear the holes on the retainer rings.
Step 4. Bolt “all” OEM lug nuts to the wheel, securing the wheel
simulator cover and the retainer ring.
Step 5. Slide on corresponding front or rear center cap and secure it
to the retainer ring with the 2 retainer ring screws supplied.
Step 6. Repeat Steps 1-5 for each of the remaining wheels.
Item 5. (2) Stainless Steel Rear
Center Caps
Item 6. (2) Rear Retainer Rings
Item 7. (8) Retainer Ring Screws
Item 8. (1) Center Cap Removal Tool
*Failure to follow all instructions could result in wheel loss, resulting in serious injury or death*
**Read all instructions before beginning installation & Follow all instructions in order presented**
! WARNING
*Failure to follow all instructions could result in wheel loss, resulting in serious injury or death*
**Read all instructions before beginning installation & Follow all instructions in order presented**
! WARNING
Item 4.
Item 4.
Item 6.
OEM Lug Nuts
Item 5.
Item 2.
OEM Lug Nuts
Item 3.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Pacific Dualies 291608 User manual

Brand
Pacific Dualies
Model
291608
Category
Car kits
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents