Sharp PN-E602 Owner's manual

Brand: Sharp

Model: PN-E602

Type: Owner's manual

This manual is also suitable for

PNE602

PN-E602

LCD MONITOR

OPERATION MANUAL

IMPORTANT:

To aid reporting in case of loss or theft, please record the

product’s model and serial numbers in the space provided.

The numbers are located in the rear of the product.

Model No.:

Serial No.:

U.S.A. ONLY

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

GREEN-AND-YELLOW: Earth

BLUE: Neutral

BROWN: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the

terminals in your plug proceed as follows:

•ThewirewhichiscolouredGREEN-AND-YELLOWmustbeconnectedtotheterminalintheplugwhichismarkedbythe

letter E or by the safety earth

orcolouredgreenorgreen-and-yellow.

•ThewirewhichiscolouredBLUEmustbeconnectedtotheterminalwhichismarkedwiththeletterN or coloured black.

•ThewirewhichiscolouredBROWNmustbeconnectedtotheterminalwhichismarkedwiththeletterL or coloured red.

Ensurethatyourequipmentisconnectedcorrectly.Ifyouareinanydoubtconsultaqualiedelectrician.

“WARNING: THIS APPARATUS MUST BE EARTHED.”

AuthorisedrepresentativeresponsiblefortheEuropeanUnionCommunityMarket

SHARPELECTRONICS(Europe)GmbH

Sonninstraße3,D-20097Hamburg

IMPORTANT INFORMATION

WARNING: TOREDUCETHERISKOFFIREORELECTRICSHOCK,DONOTEXPOSETHISPRODUCT

TORAINORMOISTURE.

RISKOFELECTRIC

SHOCK

DONOTOPEN

CAUTION

CAUTION: TOREDUCETHERISKOFELECTRIC

SHOCK,DONOTREMOVECOVER.

NOUSER-SERVICEABLEPARTS

INSIDE.

REFERSERVICINGTOQUALIFIED

SERVICEPERSONNEL.

Thelightningashwitharrowheadsymbol,within

anequilateraltriangle,isintendedtoalertthe

user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may

beofsufcientmagnitudetoconstituteariskof

electric shock to persons.

The exclamation point within a triangle is

intended to alert the user to the presence of

importantoperatingandmaintenance(servicing)

instructions in the literature accompanying the

product.

WARNING:

FCCRegulationsstatethatanyunauthorizedchangesormodicationstothisequipmentnotexpresslyapprovedbythe

manufacturercouldvoidtheuser’sauthoritytooperatethisequipment.

NOTE:

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforClassAdigitaldevice,pursuanttoPart15ofthe

FCCRules.Theselimitsaredesignedtoprovidereasonableprotectionagainstharmfulinterferencewhentheequipment

isoperatedinacommercialenvironment.Thisequipmentgenerates,uses,andcanradiateradiofrequencyenergyand,if

not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operationofthisequipmentinaresidentialareaislikelytocauseharmfulinterferenceinwhichcasetheuserwillberequired

to correct the interference at his own expense.

ThisproductutilizesaCRcoinLithiumbatterywhichcontainsaPerchloratematerial.

Special handling for this material may apply,

Californiaresidents,Seewww.dtsc.ca.gov/hazardouswaste/perchlorate/

Others,consultlocalenvironmentalofcers.

U.S.A. ONLY

IMPORTANT INFORMATION (Continued)

A. Information on Disposal for Users (private households)

1. In the European Union

Attention:Ifyouwanttodisposeofthisequipment,pleasedonotusetheordinarydustbin!

Usedelectricalandelectronicequipmentmustbetreatedseparatelyandinaccordancewithlegislationthatrequiresproper

treatment,recoveryandrecyclingofusedelectricalandelectronicequipment.

Followingtheimplementationbymemberstates,privatehouseholdswithintheEUstatesmayreturntheirusedelectricaland

electronicequipmenttodesignatedcollectionfacilitiesfreeofcharge*.Insomecountries*yourlocalretailermayalsotake

back your old product free of charge if you purchase a similar new one.

*)Pleasecontactyourlocalauthorityforfurtherdetails.

Ifyourusedelectricalorelectronicequipmenthasbatteriesoraccumulators,pleasedisposeoftheseseparatelybeforehand

accordingtolocalrequirements.

Bydisposingofthisproductcorrectlyyouwillhelpensurethatthewasteundergoesthenecessarytreatment,recoveryand

recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due

to inappropriate waste handling.

2. In other Countries outside the EU

If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.

ForSwitzerland:Usedelectricalorelectronicequipmentcanbereturnedfreeofchargetothedealer,evenifyoudon’t

purchaseanewproduct.Furthercollectionfacilitiesarelistedonthehomepageofwww.swico.chorwww.sens.ch.

B. Information on Disposal for Business Users

1. In the European Union

If the product is used for business purposes and you want to discard it:

PleasecontactyourSHARPdealerwhowillinformyouaboutthetake-backoftheproduct.Youmightbechargedforthe

costsarisingfromtake-backandrecycling.Smallproducts(andsmallamounts)mightbetakenbackbyyourlocalcollection

facilities.

ForSpain:Pleasecontacttheestablishedcollectionsystemoryourlocalauthorityfortake-backofyourusedproducts.

2. In other Countries outside the EU

If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.

Attention: Your product is marked with this symbol. It means that used electrical and electronic products

should not be mixed with general household waste. There is a separate collection system for these products.

The battery supplied with this product contains traces of Lead.

ForEU:

Thecrossed-outwheeledbinimpliesthatusedbatteriesshouldnotbeputtothegeneralhousehold

waste!Thereisaseparatecollectionsystemforusedbatteries,toallowpropertreatmentandrecyclingin

accordance with legislation. Please contact your local authority for details on the collection and recycling

schemes.

ForSwitzerland:

The used battery is to be returned to the selling point.

Forothernon-EUcountries:

Please contact your local authority for correct method of disposal of the used battery.

“BATTERYDISPOSAL”

THISPRODUCTCONTAINSALITHIUMPRIMARY(MANGANESSDIOXIDE)MEMORYBACK-UPBATTERYTHAT

MUSTBEDISPOSEDOFPROPERLY.PLEASECONTACTYOURLOCALSHARPDEALERORAUTHORIZEDSERVICE

REPRESENTATIVEFORASSISTANCEINDISPOSINGOFTHISBATTERY.

U.S.A.ANDCANADAONLY

EUONLY

ThankyouforyourpurchaseofaSHARPLCDproduct.Toensuresafetyandmanyyearsoftrouble-freeoperationofyour

product, please read the Safety Precautions carefully before using this product.

SAFETY PRECAUTIONS

Electricityisusedtoperformmanyusefulfunctions,butitcanalsocausepersonalinjuriesandpropertydamageifimproperly

handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can

resultinelectricshockand/orre.Inordertopreventpotentialdanger,pleaseobservethefollowinginstructionswheninstalling,

operatingandcleaningtheproduct.ToensureyoursafetyandprolongtheservicelifeofyourLCDproduct,pleasereadthe

following precautions carefully before using the product.

1. Readinstructions—Alloperatinginstructionsmustbereadandunderstoodbeforetheproductisoperated.

 2. Keepthismanualinasafeplace—Thesesafetyandoperatinginstructionsmustbekeptinasafeplaceforfuture

reference.

 3. Observewarnings—Allwarningsontheproductandintheinstructionsmustbeobservedclosely.

 4. Followinstructions—Alloperatinginstructionsmustbefollowed.

 5. Cleaning—UnplugthepowercordfromtheACoutletbeforecleaningtheproduct.Useadryclothtocleantheproduct.Do

notuseliquidcleanersoraerosolcleaners.

 6. Attachments—Donotuseattachmentsnotrecommendedbythemanufacturer.Useofinadequateattachmentscanresult

in accidents.

 7. Waterandmoisture—Donotusetheproductnearwater.Donotinstalltheproductinaplacewherewatermaysplashonto

it.Becarefulofequipmentwhichdrainswatersuchasanair-conditioner.

 8. Ventilation—Theventsandotheropeningsinthecabinetaredesignedforventilation.

  Donotcoverorblocktheseventsandopeningssinceinsufcientventilationcancauseoverheatingand/orshortenthelife

oftheproduct.Donotplacetheproductonasofa,rugorothersimilarsurface,sincetheycanblockventilationopenings.

Donotplacetheproductinanenclosedplacesuchasabookcaseorrack,unlessproperventilationisprovidedorthe

manufacturer’s instructions are followed.

 9. Powercordprotection—Thepowercordsmustberoutedproperlytopreventpeoplefromsteppingonthemorobjectsfrom

resting on them.

10. TheLCDpanelusedinthisproductismadeofglass.Therefore,itcanbreakwhentheproductisdroppedorappliedwith

impact.BecarefulnottobeinjuredbybrokenglasspiecesincasetheLCDpanelbreaks.

11. Overloading—DonotoverloadACoutletsorextensioncords.Overloadingcancausereorelectricshock.

12. Enteringofobjectsandliquids—Neverinsertanobjectintotheproductthroughventsoropenings.Highvoltageowsin

theproduct,andinsertinganobjectcancauseelectricshockand/orshortinternalparts.

  Forthesamereason,donotspillwaterorliquidontheproduct.

13. Servicing—Donotattempttoservicetheproductyourself.Removingcoverscanexposeyoutohighvoltageandother

dangerousconditions.Requestaqualiedservicepersontoperformservicing.

14. Repair—Ifanyofthefollowingconditionsoccurs,unplugthepowercordfromtheACoutlet,andrequestaqualiedservice

person to perform repairs.

a. Whenthepowercordorplugisdamaged.

b. Whenaliquidwasspilledontheproductorwhenobjectshavefallenintotheproduct.

c. Whentheproducthasbeenexposedtorainorwater.

d. Whentheproductdoesnotoperateproperlyasdescribedintheoperatinginstructions.

 Donottouchthecontrolsotherthanthosedescribedintheoperatinginstructions.Improperadjustmentofcontrols

notdescribedintheinstructionscancausedamage,whichoftenrequiresextensiveadjustmentworkbyaqualied

technician.

  e. Whentheproducthasbeendroppedordamaged.

  f. Whentheproductdisplaysanabnormalcondition.Anynoticeableabnormalityintheproductindicatesthattheproduct

needs servicing.

15. Replacementparts—Incasetheproductneedsreplacementparts,makesurethattheservicepersonusesreplacement

partsspeciedbythemanufacturer,orthosewiththesamecharacteristicsandperformanceastheoriginalparts.Useof

unauthorizedpartscanresultinre,electricshockand/orotherdanger.

16. Safetychecks—Uponcompletionofserviceorrepairwork,requesttheservicetechniciantoperformsafetychecksto

ensure that the product is in proper operating condition.

17. Wallmounting—Whenmountingtheproductonawall,besuretoinstalltheproductaccordingtothemethod

recommended by the manufacturer.

18. Heatsources—Keeptheproductawayfromheatsourcessuchasradiators,heaters,stovesandotherheat-generating

products(includingampliers).

DEAR SHARP CUSTOMER

SAFETY PRECAUTIONS (Continued)

19. Batteries—Incorrectuseofbatteriesmaycausethebatteriestoburstorignite.Aleakybatterymaycorrodetheequipment,

dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:

  •Usethespeciedbatteriesonly.

  •Installthebatterieswithdueattentiontotheplus(+)andminus(-)sidesofthebatteriesaccordingtotheinstructionsinthe

compartment.

  •Donotmixoldandnewbatteries.

  •Donotmixbatteriesofdifferenttypes.Voltagespecicationsofbatteriesofthesameshapemayvary.

  •Replaceanexhaustedbatterywithanewonepromptly.

  •Ifyouwillnotusetheremotecontrolforalongtime,removethebatteries.

  •Ifleakedbatteryuidgetsonyourskinorclothing,rinseimmediatelyandthoroughly.Ifitgetsintoyoureye,batheyour

eyewellratherthanrubbingandseekmedicaltreatmentimmediately.Leakedbatteryuidthatgetsintoyoureyeoryour

clothing may cause a skin irritation or damage your eye.

20. Usageofthemonitormustnotbeaccompaniedbyfatalrisksordangersthat,couldleaddirectlytodeath,personalinjury,

severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and

missile launch control in a weapon system.

21. Donotstayincontactwiththepartsoftheproductthatbecomehotforlongperiodsoftime.Doingsomayresultin

low-temperatureburns.

WARNING:

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be

requiredtotakeadequatecountermeasures.

TomaintaincompliancewithEMCregulations,useshieldedcablestoconnecttothefollowingterminals:PC/AVDVI-Doutput

terminal,PC/AVDVI-Dinputterminal,PC/AVHDMIinputterminal,PCD-SUBinputterminal,PCRGBinputterminals,and

RS-232Cinput/outputterminals.

Ifamonitorisnotpositionedinasufcientlystablelocation,itcanbepotentiallyhazardousduetofalling.Manyinjuries,

particularly to children, can be avoided by taking simple precautions such as:

•Usingxingdeviceslikewallmountbracketsrecommendedbythemanufacturer.

•Onlyusingfurniturethatcansafelysupportthemonitor.

•Ensuringthemonitorisnotoverhangingtheedgeofthesupportingfurniture.

•Notplacingthemonitorontallfurniture(forexample,cupboardsorbookcases)withoutanchoringboththefurnitureandthe

monitor to a suitable support.

•Notstandingthemonitorsonclothorothermaterialsplacedbetweenthemonitorandsupportingfurniture.

•Educatingchildrenaboutthedangersofclimbingonfurnituretoreachthemonitororitscontrols.

Especially for child safety

-Don’tallowchildrentoclimbonorplaywiththemonitor.

-Don’tplacethemonitoronfurniturethatcaneasilybeusedassteps,suchasachestofdrawers.

-Rememberthatchildrencanbecomeexcitedwhilewatchingaprogram,especiallyona“largerthanlife”monitor.Care

should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.

-Careshouldbetakentorouteallcordsandcablesconnectedtothemonitorsothattheycannotbepulledorgrabbedby

curious children.

-TheTFTcolorLCDpanelusedinthismonitorismadewith

the application of high precision technology. However, there

may be minute points on the screen where pixels never light

or are permanently lit. Also, if the screen is viewed from

an acute angle there may be uneven colors or brightness.

Please note that these are not malfunctions but common

phenomenaofLCDsandwillnotaffecttheperformanceof

the monitor.

-Donotdisplayastillpictureforalongperiod,asthiscould

cause a residual image.

-Neverrubortapthemonitorwithhardobjects.

-PleaseunderstandthatSHARPCORPORATIONbearsno

responsibility for errors made during use by the customer or

a third party, nor for any other malfunctions or damage to this

product arising during use, except where indemnity liability is

recognizedunderlaw.

-Thismonitoranditsaccessoriesmaybeupgradedwithout

advance notice.

-Donotusethemonitorwherethereisalotofdust,where

humidity is high, or where the monitor may come into contact

withoilorsteam,asthiscouldleadtore.

-Ensurethatthemonitordoesnotcomeintocontactwith

waterorotheruids.Ensurethatnoobjectssuchaspaper

clipsorpinsenterthemonitorasthiscouldleadtoreor

electric shock.

-Donotplacethemonitorontopofunstableobjectsorin

unsafeplaces.Donotallowthemonitortoreceivestrong

shocksortostronglyvibrate.Causingthemonitortofallor

topple over may damage it.

-Donotusethemonitornearheatingequipmentorinplaces

where there is likelihood of high temperature, as this may

leadtogenerationofexcessiveheatandoutbreakofre.

-Donotusethemonitorinplaceswhereitmaybeexposedto

direct sunlight.

-Imagescannotberotatedonthismonitor.

Whenusinginportraitorientation,youwillneedtoprepare

appropriately orientated content in advance.

-TheACoutletshallbeinstalledneartheequipmentandshall

be easily accessible.

The Power Cord

-Useonlythepowercordsuppliedwiththemonitor.

-Donotdamagethepowercordnorplaceheavyobjectson

it, stretch it or over bend it. Also, do not add extension cords.

Damagetothecordmayresultinreorelectricshock.

-Donotusethepowercordwithapowertap.

Addinganextensioncordmayleadtoreasaresultof

overheating.

-Donotremoveorinsertthepowerplugwithwethands.

Doingsocouldresultinelectricshock.

-Unplugthepowercordifitisnotusedforalongtime.

-Donotattempttorepairthepowercordifitisbroken

or malfunctioning. Refer the servicing to the service

representative.

Manual Scope

-Microsoft,WindowsandInternetExplorerareregistered

trademarksofMicrosoftCorporation.

-HDMI,theHDMILogoandHigh-DenitionMultimedia

InterfacearetrademarksorregisteredtrademarksofHDMI

LicensingLLC.

-Adobe,Acrobat,andReaderareeitherregisteredtrademarks

or trademarks of Adobe Systems Incorporated in the United

States and/or other countries.

-ThisproductcomeswithRICOHBitmapFontsproducedand

soldbyRICOHCOMPANY,LTD.

-Allotherbrandandproductnamesaretrademarksor

registered trademarks of their respective holders.

-LanguageofOSDmenuusedinthismanualisEnglishby

way of example.

-Illustrationsinthismanualmaynotexactlyrepresentthe

actual product or display.

-Thismanualassumesuseinlandscapeorientation,except

wherespecicallynoted.

LED Backlight

● TheLEDbacklightinthisproducthasalimitedlifetime.

 *Ifthescreengetsdarkordoesnotturnon,itmaybe

necessarytoreplacetheLEDbacklight.ThisLED

backlight is exclusive to this product and must be replaced

byanauthorizedSHARP servicing dealer or service

center.

 *PleasecontactyourlocalSHARP servicing dealer or

service center for assistance.

TIPS AND SAFETY INSTRUCTIONS

MOUNTING PRECAUTIONS

• Thisproductisforuseindoors.

• AmountingbracketcompliantwithVESAspecicationsis

required.

• Sincethemonitorisheavy,consultyourdealerbefore

installing,removingormovingthemonitor.

• Mountingthemonitoronthewallrequiresspecialexpertise

andtheworkmustbeperformedbyanauthorizedSHARP

dealer.Youshouldneverattempttoperformanyofthis

workyourself.Ourcompanywillbearnoresponsibility

foraccidentsorinjuriescausedbyimpropermountingor

mishandling.

• Usethemonitorwiththesurfaceperpendiculartoalevel

surface.Ifnecessary,themonitormaybetiltedupto20

degreesupwardordownward.

• Thismonitorshouldbeusedatanambienttemperature

between32°F(0°C)and104°F(40°C).Provide

enoughspacearoundthemonitortopreventheatfrom

accumulatinginside.

[5]

2 [5]

7-7/8 [20]

[5]

Unit: inch [cm]

For the monitor in landscape orientation

For the monitor in portrait orientation

7-7/8 [20]

2 [5]

Unit: inch [cm]

*Thismonitorcanbeinstalledclosetoawall.However,as

themonitoremitsheatduringoperation,pleasebeaware

thatthisheatmaydiscolororalterthewall.

• Ifitisdifculttoprovidesufcientspaceforanyreason

suchastheinstallationofthemonitorinsideahousing,or

iftheambienttemperaturemaybeoutsideoftherange

of32°F(0°C)to104°F(40°C),installafanortakeother

measurestokeeptheambienttemperaturewithinthe

requiredrange.

• Temperatureconditionmaychangewhenusingthemonitor

togetherwiththeoptionalequipmentsrecommendedby

SHARP.Insuchcases,pleasecheckthetemperature

conditionspeciedbytheoptionalequipments.

• Donotblockanyventilationopenings.Ifthetemperature

insidethemonitorrises,thiscouldleadtoamalfunction.

• Donotplacethemonitoronadevicewhichgeneratesheat.

• Adheretothefollowingwheninstallingthemonitorinits

portraitorientation.Failingtoadheretothefollowingmay

causemalfunctions.

-InstallthemonitorsuchthatthepowerLEDislocatedon

thebottomside.

-SettheMONITORontheSETUPmenutoPORTRAIT.

(Seepage22.)

-Besuretoclampthepowercord(supplied)ontothecable

clampattachmentusingthesuppliedcableclamp.When

clampingthepowercord,takecarenottostressthe

terminalofthepowercord.Donotbendthepowercord

excessively.

Power cord (Supplied)

Cable clamp

Cable clamp attachment

• Usethesuppliedverticalstickerwhenyouinstallthe

monitorinportraitorientation.

Logo

Operation panel

Donotremovethefactory-afxedstickerbutafxthelogo

stickeroverit.Becarefulnottocovertheremotecontrol

sensororbuttons.

Supplied Components

If any component should be missing, please contact your dealer.



LiquidCrystalDisplayMonitor:1



Remotecontrolunit:1



Cableclamp:2



Powercord:1



R-6battery(“AA”size):2



CD-ROM(UtilityDiskforWindows):1



SetupManual:1



Verticalsticker(Operationpanel):1



Verticalsticker(Logo):1



Terminallabel:1

UsedwheninstallingtheexpansionboardPN-ZB01(optional).



CoverSharplogo:1

Place this sticker onto the SHARP logo to cover the logo.

* SharpCorporationholdsauthorshiprightstotheUtilityDiskprogram.Donotreproduceitwithoutpermission.

* Forenvironmentalprotection!

 Donotdisposeofbatteriesinhouseholdwaste.Followthedisposalinstructionsforyourarea.

Contents

IMPORTANT INFORMATION ............................................3

DEAR SHARP CUSTOMER ..............................................5

SAFETY PRECAUTIONS ..................................................5

TIPS AND SAFETY INSTRUCTIONS ...............................7

MOUNTING PRECAUTIONS ............................................8

Supplied Components .....................................................9

Part Names .....................................................................10

Connecting Peripheral Equipment ...............................12

ConnectionwithaPCorAVequipment .....................12

ConnectionwhenthePN-ZB01(optional)

is attached ..................................................................13

Connecting the Power Cord .........................................14

Binding Cables ...............................................................14

Removing the Handles ..................................................14

Preparing the Remote Control Unit ..............................15

Installing the batteries ................................................15

Remote control operation range .................................15

Turning Power On/Off ....................................................16

Turning on the main power.........................................16

Turning power on/off ..................................................16

Disablingpoweron/offoperations ..............................17

Basic Operation .............................................................18

Menu Items .....................................................................20

Displayingthemenuscreen .......................................20

Menu item details .......................................................21

AdjustmentsforPCscreendisplay ............................28

Initialization (Reset)/Functional Restriction Setting

(FUNCTION) ....................................................................29

Controlling the Monitor with a PC (RS-232C) ..............30

PCconnection ............................................................30

Communicationconditions .........................................30

Communicationprocedure .........................................30

SettingoftheGAMMAuserdata ................................33

RS-232Ccommandtable ...........................................34

Controlling the Monitor with a PC (LAN) .....................42

Settings to connect to a LAN ......................................42

ControllingwithaPC ..................................................44

Troubleshooting .............................................................50

Specications ...............................................................52

Mounting Precautions

(For SHARP dealers and service engineers) ...............56

Front view

2345

1. LCD panel

2. Remote control sensor (Seepage15.)

3. Input switch (Seepage18.)

4. Power switch (Seepage16.)

5. Power LED (Seepage16.)

TIPS

• Useapointedobjectsuchasapentiptopressthe

switches at the front of the monitor.

Part Names

Rear view

13 14

When the PN-ZB01

(optional) is attached

1. Optional attachment section

This section is used to connect optional

hardware for function expansion.

Offering this attachment location is

not a guarantee that future compatible

hardware attachments will be released.

2. Speakers

3. Handles (Seepage14.)

4. Vents

5. Expansion terminal cover

Additional input/output terminals are

availablebyattachingthePN-ZB01

expansionboard(optional).

6. PC/AV HDMI input terminal (Seepage

12.)

7. PC D-sub input terminal (Seepage

12.)

8. Audio input terminal (Seepage12.)

9. Audio output terminals (Seepage12.)

10. RS-232C output terminal (Seepage

12.)

11. RS-232C input terminal (Seepage12.)

12. Optional terminal

This terminal is provided for possible

future(optional)functionexpansion.

Offering of this terminal is not a

guarantee that future expanded

functionality will be provided.

13. AC input terminal (Seepage14.)

14. Main power switch (Seepage16.)

Caution

• ConsultyourSHARPdealerforattachment/detachmentof

optional parts.

• Donotopentheexpansionterminalcoverbyyourself.

There are high voltage parts inside the cover which may

cause an electric shock.

When the PN-ZB01 (optional) is attached

15. PC/AV DVI-D input terminal (Seepage13.)

16. PC/AV DVI-D output terminal (Seepage13.)

17. LAN terminal (Seepage13.)

18. External speaker terminals (Seepage13.)

19. Audio 1 input terminals (Seepage13.)

20. Audio 2 input terminals (Seepage13.)

21. PC RGB input terminals (Seepage13.)

22. AV component input terminals (Seepage13.)

23. AV video input terminal (Seepage13.)

24. AV S-video input terminal (Seepage13.)

Part Names

Remote control unit

1. Signal transmitter

2. POWER button(Seepage16.)

3. MUTE button(Seepage18.)

4. VOL +/- buttons(Seepage18.)

BRIGHT +/- buttons(Seepage18.)

Cursor control (

/ / / ) buttons

5. DISPLAY button(Seepage18.)

6. MODE button(Seepage18.)

7. INPUT button(Seepage18.)

8. MENU button(Seepage18.)

9. SIZE button(Seepage18.)

Connecting Peripheral Equipment

Caution

 







 







TIPS

 



 







 



 









 













 



Input mode

Audio input terminal

(Factory setting)





 

















 

Connection with a PC or AV equipment

1. PC/AV HDMI input terminal

 



 



 







2. PC D-sub input terminal

 



 

 





 



3. Audio input terminal

 

 





4. Audio output terminals

 

 



 



5. RS-232C input terminal

RS-232C output terminal

 





When the PN-ZB01 (optional) is attached

Connecting Peripheral Equipment

Connection when the PN-ZB01

(optional) is attached

ThePN-ZB01expansionboard(optional)allowstheuseof

additional connection terminals.

6. PC/AV DVI-D input terminal

• SetDVIofINPUTSELECTontheOPTIONmenu

according to the device to be connected.

• SelecttheaudioinputterminaltobeusedinPCDVI-Dor

AVDVI-DofAUDIOSELECTontheOPTIONmenu.

7. PC RGB input terminals

• SetBNCofINPUTSELECTontheOPTIONmenutoPC

RGBwhenusingthePCRGBinputterminals.

• SelecttheaudioinputterminaltobeusedinPCRGBof

AUDIOSELECTontheOPTIONmenu.

8. AV component input terminals

• SetBNCofINPUTSELECTontheOPTIONmenuto

AVCOMPONENTwhenusingtheAVcomponentinput

terminals.

• SelecttheaudioinputterminaltobeusedinAV

COMPONENTofAUDIOSELECTontheOPTIONmenu.

• CannotbeusedwhenD-SUBinINPUTSELECTonthe

OPTIONmenuissettoAVCOMPONENT.

9. AV video input terminal

• SelecttheaudioinputterminaltobeusedinAVVIDEOof

AUDIOSELECTontheOPTIONmenu.

• CannotbeusedwhenD-SUBinINPUTSELECTonthe

OPTIONmenuissettoAVVIDEO.

10. AV S-video input terminal

• SelecttheaudioinputterminaltobeusedinAVS-VIDEO

ofAUDIOSELECTontheOPTIONmenu.

11. Audio1 input terminals / Audio2 input terminals

• Settheaudioinputterminaltobeusedineachinput

modeinAUDIOSELECTontheOPTIONmenu.

12. LAN terminal

• YoucancontrolthemonitorfromaPConanetworkby

connecting a commercially available LAN cable between

this terminal and a network.

13. External speaker terminals

• Touseexternalspeakers,setSPEAKERSELECTonthe

SETUPmenutoEXTERNAL.

• Besuretouseexternalspeakerswithanimpedanceof6Ω

orgreaterandaratedinputofatleast7W.

132

Approx.

3-15/16 inch

(10 cm)

1.Attachaspeakercablecore(includedwiththePN-ZB01)to

the end of the speaker cable connected to the monitor.

2.Whilepushingthetab,insertthetipofthecable.

3. Release the tab.

TIPS

• Besuretoconnectthe+and-terminalsandtheleftand

right speakers properly.

• Avoidshortcircuitingthe+and-terminals.

• WhenSPEAKERSELECTissettoEXTERNAL,the

internal speakers are disabled.

14. PC/AV DVI-D output terminal

• ThevideoofthePC/AVDVI-Dinputcanbeoutputtoan

external device.

• OutputtingHDCP-encryptedvideorequiresanexternal

devicewhichsupportsHDCP.

• Thisterminalallowsthedaisychainconnectionofupto5

monitors.

TIPS

• Thelengthofthesignalcablesorsurroundingenvironment

mayaffecttheimagequality.

• Thescreenmaynotdisplayproperlywhenusingterminals

otherthanPCDVI-D/AVDVI-Dfortheinputmode.Inthis

case, turn off the power to all the monitors connected in a

daisy chain and then turn the power on again.

• WhenconnectingmonitorsinadaisychainsetAUTO

INPUTCHANGEtoOFF.

• Videooutputisdisabledinthefollowingcases:

Whenthepoweristurnedoff

Whenthemonitorisininputsignalwaitingmode

Connecting the Power Cord

Caution

• Useonlythepowercordsuppliedwiththemonitor.

1.Turnoffthemainpowerswitch.

2.Plugthepowercord(supplied)intotheACinputterminal.

3.Plugthepowercord(supplied)intotheACpoweroutlet.

Binding Cables

Thecablesconnectedtotheterminalsontherearofthe

monitorcanbefastenedwiththecableclamp.

Insertthecableclampintothecableclampattachmentonthe

rearofthemonitorandfastenthecables.

AC input terminal

Main power switch

Power cord (Supplied)

For power

outlet

Removing the Handles

Cable clamp

attachment

Cable

Thehandlescanberemoved.

Handle

Handle screws

Caution

• Theremovablehandlesandhandlescrewsareforusewiththismonitor.Donotusethemforanyotherdevices.

• Toattachhandles,besuretousethehandlesandhandlescrewswhichwereremovedfromthemonitor.

• Besurethehandlesareattachedsecurely.

Preparing the Remote Control Unit

Installing the batteries

1. Pressthecovergentlyandslideitinthedirectionofthe

arrow.

2. Seetheinstructionsinthecompartmentandputinthe

suppliedbatteries(R-6(“AA”size)x2)withtheirplus(+)

andminus(-)sidesorientedcorrectly.

3. Closethecover.

TIPS

• Whenthebatteriesbecomeexhausted,replacethemwith

new(commerciallyavailable)batteries.

• Thesuppliedbatteries(R-6(“AA”size)x2)maybecome

exhaustedquicklydependingonhowtheyarestored.

• Ifyouwillnotbeusingtheremotecontrolforalongtime,

remove the batteries.

• Usemanganeseoralkalinebatteriesonly.

Remote control operation range

Theoperationrangeoftheremotecontrolunitisapprox.16.4

feet(5m)atanangleofapprox10°fromthecentertothetop/

bottom/right/left of the remote control sensor.

10°10°

10°

Remote

control sensor

16.4

feet

(5 m)

TIPS

• Donotexposetheremotecontrolunittoshockbydropping

or stepping on it. This could lead to a malfunction.

• Donotexposetheremotecontrolunittoliquids,anddonot

place it in an area with high humidity.

• Theremotecontrolunitmaynotworkproperlyiftheremote

control sensor is under direct sunlight or strong lighting.

• Objectsbetweentheremotecontrolunitandtheremote

control sensor may prevent proper operation.

• Replacethebatterieswhentheyrunlowasthismay

shorten the remote control’s operation range.

• Ifauorescentlightisilluminatedneartheremotecontrol

unit, it may interfere with proper operation.

• Donotuseitwiththeremotecontrolofotherequipment

such as air conditioner, stereo components, etc.

Caution

• TurnonthemonitorrstbeforeturningonthePCor

playbackdevice.

Turning on the main power

Main power switch

Caution

• Themainpowermustbeturnedon/offwiththemainpower

switch.Donotconnect/disconnectthepowercordorturn

thebreakeron/offwhilethemainpowerswitchison.

• WhenswitchingthemainpowerswitchorthePOWER

buttonoffandbackon,alwayswaitforatleast5seconds.

• Foracompleteelectricaldisconnection,pulloutthemain

plug.

Turning Power On/Off

Turning power on/off

PressthePOWERbuttonorPOWERswitchtoturnthepower

ON/OFF.

Power LED

Status Status of the monitor

Greenlit Poweron

Orangelit Poweroff(Standbymode)

Greenashing Inputsignalwaitingmode

Caution

• WhenswitchingthemainpowerswitchorthePOWER

buttonoffandbackon,alwayswaitforatleast5seconds.

Ashortintervalmayresultinamalfunction.

TIPS

• Whenthemainpowerswitchisoff,themonitorcannotbe

turnedon.

• Ifthemonitorisintheinputsignalstandbymodeandyou

pressthePOWERbuttonontheremotecontrolunit,the

monitorentersstandbymode.

• SettingtheSCHEDULEashesthepowerLEDalternately

inredandorangeinstandbymode.

• Todisablethelogoscreenfromdisplayingwhenturning

thepowerON,setLOGOSCREENtoOFFontheSETUP

menu.(Seepage23.)

Turning Power On/Off

Operation mode

Whenthemonitoristurnedonforthersttimeafterbeing

shipped from the factory, the operation mode setting screen

willbedisplayed.SetittoMODE1orMODE2.

MODE1 ....OFFIFNOOPERATIONissettoON,and

STANDBYMODEissettoLOWPOWER.(These

settingscannotbechanged.)

If there is no operation for 4 hours or more, the

monitor automatically enters standby mode. Power

consumptioninstandbymodeisalsominimized.

MODE2 ....Willperformstandardoperation.

OFFIFNOOPERATIONissettoOFF,and

STANDBYMODEissettoSTANDARD.These

settings can be changed.

Evenafterbeingset,changescanbemadeusing

OPERATIONMODE,locatedinthemenuofthemonitor.(See

page22.)

Date/time setting

• Ifthetimehasyettobesetwhenthemonitorisrstturned

on, the date/time setting screen appears. Set the date and

time.

DATE/TIME SETTING

SET

CANCEL

OK···[MENU]

: :

01 01 11

00 00

:/ 20

1. Press , , or to select the date and

time, and press

or to change the numerical

values.

2. Press

or toselectSETandthenpress

• Besuretosetthedateandtime.

• Thedate/timesettingscreenwillcloseautomaticallyifno

operationisperformedforabout15seconds.Thedate

andtimecanbesetusingDATE/TIMESETTINGfrom

the OPTION menu when the date/time setting screen

disappears.

TIPS

•

Setthedatein“Day/Month/Year”order.

•

Setthetimeona24-hourbasis.

•

The clock is maintained by the internal battery.

•

If you already set the time but the date/time setting

screen appears when the power is turned on, the

internal battery may be exhausted. Please contact

your local SHARP servicing dealer or service center for

assistance with battery replacement.

•

Estimatedservicelifeoftheinternalbattery:About5

years(dependingonmonitoroperation)

•

The initial battery was inserted at the factory when the

monitor was shipped, so it may run out of power before

its expected operation life.

Disabling power on/off operations

Power on/power off operations can be disabled in order to

protect the monitor from an accidental power off. Set the

ADJUSTMENTLOCKinFUNCTIONmenuto“ON2”.(See

page29.)

Basic Operation

1. INPUT (Input mode selection)

The menu is displayed. Press

or to select the input

mode, and press

to enter.

* Youcanselecttheinputterminalbypressingtheinput

switch of the monitor.

Input mode Video Audio

PCD-SUB PCD-subinputterminal

Audio input terminal

PCHDMI

PC/AVHDMIinputterminal

AVHDMI

PC/AVHDMIinputterminal

AVCOMPONENT PCD-subinputterminal

Audio input terminal

AVVIDEO PCD-subinputterminal

When the PN-ZB01 (optional) is attached

Input mode Video Audio

PCDVI-D

PC/AVDVI-Dinputterminal

PCHDMI

PC/AVHDMIinputterminal

PCD-SUB PCD-subinputterminal

PCRGB PCRGBinputterminals

AVDVI-D

PC/AVDVI-Dinputterminal

AVHDMI

PC/AVHDMIinputterminal

AVCOMPONENT

AVCOMPONENTinput

terminals

PCD-subinputterminal

AVS-VIDEO AVS-videoinputterminal

AVVIDEO

AVvideoinputterminal

PCD-subinputterminal

*1 SelecttheterminaltobeusedinD-SUBofINPUT

SELECT.(Seepage23.)

*2 SelecttheterminaltobeusedinHDMIofINPUTSELECT.

(Seepage23.)

*3 SelecttheterminalforAUDIOSELECTwhichisusedfor

audioinput.(Seepage23.)

*4 SelecttheterminaltobeusedinDVIofINPUTSELECT.

(Seepage23.)

*5 SelecttheterminaltobeusedinBNCofINPUTSELECT.

(Seepage23.)

2. MUTE

Turns off the volume temporarily.

PresstheMUTEbuttonagaintoturnthesoundbacktothe

previous level.

3. MENU

Displaysandturnsoffthemenuscreen.(seepage20.)

4. VOL +/- (Volume adjustment)

Pressing

or displaystheVOLUMEmenuwhenthe

menu screen is not displayed.

V OLUME 15

Press or toadjustthevolumeofthesound.

* Ifyoudonotpressanybuttonsforabout4seconds,the

VOLUMEmenuautomaticallydisappears.

5. BRIGHT +/- (Backlight adjustment)

Pressing

or displaystheBRIGHTmenuwhenthe

menu screen is not displayed.

BRIGHT 15

Press

or toadjustthebrightness.

* Ifyoudonotpressanybuttonsforabout4seconds,the

BRIGHTmenuautomaticallydisappears.

6. SIZE (Screen size selection)

The menu is displayed.

Press

or toselectthescreensize.(Seepage19.)

7. DISPLAY

Displaysmonitorinformation.Whenyoupressthisbutton

again, the display disappears.

WhenthePN-ZB01(optional)isattached,thedisplaychanges

fromINFORMATION1→INFORMATION2→cleardisplay,

and so on every time you press this button.

• Thedisplaydisappearsautomaticallyafterabout15

seconds.

•

LAN

is displayed during LAN communication.

• If

LAN

is displayed in red, there is a duplicate IP address.

8. MODE (Color mode selection)

Eachtimeyoupressthisbutton,thecolormodechangesin

the following order:

STD(Standard)→VIVID→sRGB→

HIGHILLUMINANCE→STD...

• HIGHILLUMINANCEisadisplaywithcolorssuitedto

bright locations.

• sRGBappliestoPCinputonly.

 sRGBisinternationalstandardofcolorrepresentation

speciedbyIEC(InternationalElectrotechnical

Commission).Colorconversionismadeintakingaccount

ofliquidcrystal’scharacteristicsandrepresentscolortone

close to its original image.

Basic Operation

Switching the screen size

Evenwhenthescreensizeischanged,thedisplaymayremainthesamedependingontheinputsignal.

WIDE PCinput Displaysimagesoitllstheentirescreen.

AVinput Animagewitha4:3aspectratioisstretchedtolltheentire

screen.

ZOOM 1

PCinput Animagewitha4:3aspectratioisenlargedtolltheentirescreen

without changing the aspect ratio. The edges of the image may be

cut off.

AVinput

ZOOM 2

PCinput UsethissizeifZOOM1cutsoffthesubtitles.

AVinput

NORMAL

PCinput Displaysimagesoitllsthescreenwithoutchangingtheaspect

ratio of the input signals.

AVinput Displaystheentireimageoftheaspectratioof4:3without

changing the aspect ratio.

Dot by Dot

PCinput DisplaysthedotsofthesignalsinputfromtheconnectedPCas

the corresponding dots on the screen.

AVinput Displaysthedotsoftheinputsignalsasthecorrespondingdotson

the screen.

TIPS

• Usingthismonitor’sscreen-sizeswitchingordual-screendisplayfunctionstocompressorexpandthescreenforcommercial

orpublicviewinginestablishmentslikecafesorhotelsmayinfringeontherightsofthecreators,asprotectedbyCopyright

Law, so please be careful.

• When“Enlarge”isset,thescreensizeisxedto“WIDE”mode.

• Whendual-screendisplayisselected,thescreensizecannotbechanged.

• Theappearanceoftheoriginalvideomaychangeifyouselectascreensizewithadifferentaspectratiothantheoriginal

image(e.g.TVbroadcastorvideoinputfromexternalequipment).

• Whenanordinarynon-wideimage(4:3)isviewedwiththewholescreenusingthescreen-sizeswitchingfunctionofthis

monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen

sizeto“NORMAL”.

• Whenplayingcommercialsoftware,partsoftheimage(likesubtitles)maybecropped.Inthiscaseselecttheoptimalscreen

sizeusingthescreen-sizeswitchingfunctionofthismonitor.Withsomesoftware,theremaybenoiseordistortionatthe

edges of the screen. This is due to the characteristics of the software, and is not a malfunction.

• Dependingontheoriginalimagesize,blackbandsmayremainattheedgesofthescreen.

Menu Items

Displaying the menu screen

Video and audio adjustment and settings of various functions

are enabled. This section describes how to use the menu

items. See pages 21 to 25 for details of each menu items.

Caution

• Donotturnthemainpowerswitchoffwhilethemenuitems

arebeingdisplayed.Doingsomayinitializethesettings.

Example of operation

(Adjusting CONTRAST in the PICTURE menu)

1. Press

to display the menu screen.

1 920x1080

V: 60 Hz H: 67.5 kHz

AUTO

CLOCK

PHASE

H-POS

V-POS

H-SIZE

V-SIZE

H-RESOLUTION

V-RESOLUTION

RESET

SCREEN

PICTURE

AUDIO

SETUP

OPTION

PIP/PbyP

MULTI

600

610

1920

1080

SCREEN

1/1

END···[MENU]

PC D-SUB

2. Press

to select PICTURE, and press

3. Press

to select CONTRAST.

AUTO

ANALOG GAIN

ANALOG OFFSET

BRIGHT

CONTRAST

BLACK LEVEL

TINT

COLORS

SHARPNESS

RGB INPUT RANGE

1/2

FULL

PC D-SUB

PICTURE

SCREEN

PICTURE

AUDIO

SETUP

OPTION

PIP/PbyP

MULTI

OK···[MENU]MOVE OSD···[DISPLAY]

1 920x1080

V: 60 Hz H: 67.5 kHz

4. Press or

to adjust the setting.

▲

AUTO

ANALOG GAIN

ANALOG OFFSET

BRIGHT

CONTRAST

BLACK LEVEL

TINT

COLORS

SHARPNESS

RGB INPUT RANGE

1/2

FULL

PC D-SUB

PICTURE

SCREEN

PICTURE

AUDI

OPTION

PIP/PbyP

MULTI

SETUP

OK···[MENU]MOVE OSD···[DISPLAY]

1 920x1080

V: 60 Hz H: 67.5 kHz

For items that have , press , make settings and then

press

5. Press

twice to close the menu screen.

TIPS

• Themenuwilldifferdependingontheinputmode.

• Themenuscreenwillcloseautomaticallyifnooperationis

performedforabout15seconds.(DATE/TIMESETTING,

SCHEDULEandLANSETUPscreenswillcloseinabout4

minutes.)

Menu screen display

▲

AUTO

ANALOG GAIN

ANALOG OFFSET

BRIGHT

CONTRAST

BLACK LEVEL

TINT

COLORS

SHARPNESS

RGB INPUT RANGE

1/2

FULL

PC D-SUB

SCREEN

PICTURE

AUDIO

SETUP

OPTION

PIP/PbyP

MULTI

PICTURE

OK···[MENU]MOVE OSD···[DISPLAY]

1920x1080

V: 60 Hz H: 67.5 kHz

1 Name of the menu

2 Input mode

3 An item being selected (highlighted)

4 Screenresolutionofinputsignal,andotherdata.

TIPS

• Itemsthatcannotbeselectedappearingray.

(e.g. Function not supported by the current input signal)

Menu Items

The displayed menu items vary depending on whether or not

the PN-ZB01 (optional) is attached.

The following menus will be displayed only when the PN-ZB01

(optional) is attached.

Menu Item

SETUP HOTPLUGCONTROL DVI

RS-232C/LANSELECT

LANSETUP

AUTOASSIGNFIXEDIPADDR.

SPEAKERSELECT

OPTION INPUTSELECT DVI

BNC

AUDIOSELECT PCDVI-D

PCD-SUB

PCRGB

AVDVI-D

AVCOMPONENT(BNC)

AVCOMPONENT(D-SUB)

AVS-VIDEO

AVVIDEO(BNC)

AVVIDEO(D-SUB)

PIP/PbyP PIP SOURCE

Page is loading ...

Sharp PN-E602 Owner's manual

Brand: Sharp

Model: PN-E602

Type: Owner's manual

This manual is also suitable for

PNE602

Download PDF

report

Sharp PN-E602 Owner's manual

This manual is also suitable for

Sharp PN-E602 Owner's manual

Related papers

Other documents