Dell PowerEdge T640 Reference guide

Brand: Dell

Model: PowerEdge T640

Type: Reference guide

Dell EMC PowerEdge T640

BIOS and UEFI Reference Guide

Part Number: E47S Series

Regulatory Type: E47S001

December 2020

Rev. A00

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better use of your product.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

WARNING: A WARNING indicates a potential for property damage, personal injury, or death.

Other trademarks may be trademarks of their respective owners.

Chapter 1: Pre-operating system management applications...........................................................4

Options to manage the pre-operating system applications.......................................................................................4

System Setup....................................................................................................................................................................... 4

Viewing System Setup..................................................................................................................................................4

System Setup details.................................................................................................................................................... 5

System BIOS................................................................................................................................................................... 5

iDRAC Settings utility................................................................................................................................................. 26

Device Settings............................................................................................................................................................ 27

Dell Lifecycle Controller................................................................................................................................................... 27

Embedded system management.............................................................................................................................. 27

Boot Manager.....................................................................................................................................................................27

Viewing Boot Manager............................................................................................................................................... 27

Boot Manager main menu..........................................................................................................................................27

One-shot UEFI boot menu........................................................................................................................................ 28

System Utilities............................................................................................................................................................ 28

PXE boot............................................................................................................................................................................. 28

Contents

Contents 3

Pre-operating system management

applications

You can manage basic settings and features of a system without booting to the operating system by using the system firmware.

Topics:

• Options to manage the pre-operating system applications

• System Setup

• Dell Lifecycle Controller

• Boot Manager

• PXE boot

Options to manage the pre-operating system

applications

Your system has the following options to manage the pre-operating system applications:

● System Setup

● Dell Lifecycle Controller

● Boot Manager

● Preboot Execution Environment (PXE)

System Setup

By using the System Setup screen, you can configure the BIOS settings, iDRAC settings, and device settings of your system.

NOTE:

Help text for the selected field is displayed in the graphical browser by default. To view the help text in the text

browser, press F1.

You can access system setup by one of the following:

● Standard graphical browser—The browser is enabled by default.

● Text browser—The browser is enabled by using Console Redirection.

Viewing System Setup

To view the System Setup screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

4 Pre-operating system management applications

System Setup details

The System Setup Main Menu screen details are explained as follows:

Option Description

System BIOS Enables you to configure BIOS settings.

iDRAC Settings Enables you to configure the iDRAC settings.

The iDRAC settings utility is an interface to set up and configure the iDRAC parameters by using UEFI

(Unified Extensible Firmware Interface). You can enable or disable various iDRAC parameters by using the

iDRAC settings utility. For more information about this utility, see Integrated Dell Remote Access

Controller User’s Guide at www.dell.com/poweredgemanuals.

Device Settings Enables you to configure device settings.

System BIOS

You can use the System BIOS screen to edit specific functions such as boot order, system password, and setup password, set

the SATA and PCIe NVMe RAID mode, and enable or disable USB ports.

Viewing System BIOS

To view the System BIOS screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If the operating system begins to load before you press F2, wait for the system to finish booting, and then

restart the system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

System BIOS Settings details

About this task

The System BIOS Settings screen details are explained as follows:

Option

Description

System

Information

Provides information about the system such as the system model name, BIOS version, and Service Tag.

Memory Settings Provides information and options related to the installed memory.

Processor

Settings

Provides information and options related to the processor such as speed and cache size.

SATA Settings Provides options to enable or disable the integrated SATA controller and ports.

NVMe Settings Provides options to change the NVMe settings. If the system contains the NVMe drives that you want to

configure in a RAID array, you must set both this field and the Embedded SATA field on the SATA

Settings menu to RAID mode. You might also need to change the Boot Mode setting to UEFI.

Otherwise, you should set this field to Non-RAID mode.

Boot Settings Provides options to specify the Boot mode (BIOS or UEFI). Enables you to modify UEFI and BIOS boot

settings.

Pre-operating system management applications 5

Option Description

Network Settings Provides options to manage the UEFI network settings and boot protocols.

Legacy network settings are managed from the Device Settings menu.

Integrated

Devices

Provides options to manage integrated device controllers and ports, specifies related features and

options.

Serial

Communication

Provides options to manage the serial ports, their related features and options.

System Profile

Settings

Provides options to change the processor power management settings, and memory frequency.

System Security Provides options to configure the system security settings, such as system password, setup password,

Trusted Platform Module (TPM) security, and UEFI secure boot. It also manages the power button on the

system.

Redundant OS

Control

Sets the redundant OS information for redundant OS control.

Miscellaneous

Settings

Provides options to change the system date and time.

System Information

You can use the System Information screen to view system properties such as Service Tag, system model name, and BIOS

version.

Viewing System Information

To view the System Information screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click System Information.

System Information details

About this task

The System Information screen details are explained as follows:

Option

Description

System Model

Name

Specifies the system model name.

System BIOS

Version

Specifies the BIOS version installed on the system.

System

Management

Engine Version

Specifies the current version of the Management Engine firmware.

6 Pre-operating system management applications

Option Description

System Service

Tag

Specifies the system Service Tag.

System

Manufacturer

Specifies the name of the system manufacturer.

System

Manufacturer

Contact

Information

Specifies the contact information of the system manufacturer.

System CPLD

Version

Specifies the current version of the system complex programmable logic device (CPLD) firmware.

UEFI Compliance

Version

Specifies the UEFI compliance level of the system firmware.

Memory Settings

You can use the Memory Settings screen to view all the memory settings and enable or disable specific memory functions,

such as system memory testing and node interleaving.

Viewing Memory Settings

To view the Memory Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If the operating system begins to load before you press F2, wait for the system to finish booting, and then

restart the system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Memory Settings.

Memory Settings details

About this task

The Memory Settings screen details are explained as follows:

Option

Description

System Memory

Size

Specifies the memory size in the system.

System Memory

Type

Specifies the type of memory that is installed in the system.

System Memory

Speed

Specifies the system memory speed.

System Memory

Voltage

Specifies the system memory voltage.

Video Memory Specifies the amount of video memory.

Pre-operating system management applications 7

Option Description

System Memory

Testing

Specifies whether the system memory tests are run during system boot. Options are Enabled and

Disabled. This option is set to Disabled by default.

Dram Refresh

Delay

By enabling the CPU memory controller to delay running the REFRESH commands, you can improve

the performance for some workloads. By minimizing the delay time, it is ensured that the memory

controller runs the REFRESH command at regular intervals. For lntel-based servers, this setting only

affects systems configured with DIMMs which use 8 Gb density DRAMS.

Memory

Operating Mode

Specifies the memory operating mode. The options available are Optimizer Mode, Single Rank Spare

Mode, Multi Rank Spare Mode, Mirror Mode, and Dell Fault Resilient Mode. This option is set to

Optimizer Mode by default.

NOTE: The Memory Operating Mode option can have different default and available options based

on the memory configuration of your system.

NOTE: The Dell Fault Resilient Mode option establishes an area of memory that is fault resilient.

This mode can be used by an operating system that supports the feature to load critical applications

or enables the operating system kernel to maximize system availability.

NOTE: Only Optimizer Mode should be selected when Intel DC Optane Persistent Memory is

installed.

Current State of

Memory

Operating Mode

Specifies the current state of the memory operating mode.

Node Interleaving Specifies if Non-Uniform Memory Architecture (NUMA) is supported. If this field is set to Enabled,

memory interleaving is supported if a symmetric memory configuration is installed. If this field is set to

Disabled, the system supports NUMA (asymmetric) memory configurations. This option is set to

Disabled by default.

ADDDC Setting Enables or disables ADDDC Setting feature. When Adaptive Double DRAM Device Correction (ADDDC)

is enabled, failing DRAMs are dynamically mapped out. When set to Enabled it can have some impact to

system performance under certain workloads. This feature is applicable for x4 DIMMs only. This option is

set to Disabled by default.

Native tRFC

Timing for 16Gb

DIMMs

Enables 16 Gb density DIMMs to operate at their programmed Row Refresh Cycle Time (tRFC). Enabling

this feature may improve system performance for some configurations. However, enabling this feature

has no effect on configurations with 16 Gb 3DS/TSV DIMMs. This option is set to Enabled by default.

Opportunistic

Self-Refresh

Enables or disables opportunistic self-refresh feature. This option is set to Disabled by default and is not

supported when DCPMMs are in the system.

Correctable Error

logging

Enables or disables logging of correctable memory threshold error. This option is set to Enabled by

default.

Persistent

Memory

This field controls Persistent Memory on the system. This option is only available if the persistent memory

module is installed in the system.

Persistent Memory details

About this task

The Persistent Memory screen details can be found in the NVDIMM-N User Guide and DCPMM User Guideat https://

www.dell.com/poweredgemanuals.

Pre-operating system management applications

Processor Settings

You can use the Processor Settings screen to view the processor settings and perform specific functions such as enabling

virtualization technology, hardware prefetcher, logical processor idling.

Viewing Processor Settings

To view the Processor Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Processor Settings.

Processor Settings details

About this task

The Processor Settings screen details are explained as follows:

Option

Description

Logical

Processor

Enables or disables the logical processors and displays the number of logical processors. If this option is

set to Enabled, the BIOS displays all the logical processors. If this option is set to Disabled, the BIOS

displays only one logical processor per core. This option is set to Enabled by default.

CPU

Interconnect

Speed

Enables you to govern the frequency of the communication links among the processors in the system.

NOTE: The standard and basic bin processors support lower link frequencies.

The options available are Maximum data rate, 10.4 GT/s, and 9.6 GT/s. This option is set to Maximum

data rate by default.

Maximum data rate indicates that the BIOS runs the communication links at the maximum frequency that

is supported by the processors. You can also select specific frequencies that the processors support,

which can vary.

For best performance, you should select Maximum data rate. Any reduction in the communication link

frequency affects the performance of non-local memory accesses and cache coherency traffic. Besides,

it can slow access to non-local I/O devices from a particular processor.

However, if power-saving considerations outweigh performance, you might want to reduce the frequency

of the processor communication links. If you do this, you should localize memory and I/O accesses to the

nearest NUMA node to minimize the impact to system performance.

Virtualization

Technology

Enables or disables the virtualization technology for the processor. This option is set to Enabled by

default.

Adjacent Cache

Line Prefetch

Optimizes the system for applications that need high utilization of sequential memory access. This option

is set to Enabled by default. You can disable this option for applications that need high utilization of

random memory access.

Hardware

Prefetcher

Enables or disables the hardware prefetcher. This option is set to Enabled by default.

Software

Prefetcher

Enables or disables the software prefetcher. This option is set to Enabled by default.

Pre-operating system management applications 9

Option Description

DCU Streamer

Prefetcher

Enables or disables the Data Cache Unit (DCU) streamer prefetcher. This option is set to Enabled by

default.

DCU IP

Prefetcher

Enables or disables the Data Cache Unit (DCU) IP prefetcher. This option is set to Enabled by default.

Sub NUMA

Cluster

Sub NUMA Clustering (SNC) is a feature for breaking up the LLC into disjoint clusters based on address

range, with each cluster bound to a subset of the memory controllers in the system. It improves average

latency to the LLC. Enables or disables the Sub NUMA Cluster. This option is set to Disabled by default.

UPI Prefetch Enables you to get the memory that is read started early on DDR bus. The Ultra Path Interconnect (UPI)

Rx path will spawn the speculative memory that is read to Integrated Memory Controller (iMC) directly.

This option is set to Enabled by default.

LLC Prefetch Enables or disables the LLC Prefetch on all threads. This option is set to Disabled by default.

Dead Line LLC

Alloc

Enables or disables the Dead Line LLC Alloc. This option is set to Enabled by default. You can enable this

option to enter the dead lines in LLC or disable the option to not enter the dead lines in LLC.

Directory AtoS Enables or disables the Directory AtoS. AtoS optimization reduces remote read latencies for repeat read

accesses without intervening writes. This option is set to Disabled by default.

Logical

Processor Idling

Enables you to improve the energy efficiency of a system. It uses the operating system core parking

algorithm and parks some of the logical processors in the system which in turn allows the corresponding

processor cores to transition into a lower power idle state. This option can only be enabled if the

operating system supports it. It is set to Disabled by default.

Intel SST-BF Enable Intel SST-BF. This option is displayed if Performance Per Watt (operating system) or Custom

(when OSPM is enabled) system profiles are selected. It is set to Disabled by default.

Intel SST-CP Enable Intel SST-CP. This option is displayed if Performance Per Watt (operating system) or Custom

(when OSPM is enabled) system profiles are selected. It is set to Disabled by default.

Configurable TDP Enables you to configure the TDP level. The available options are Nominal, Level 1, and Level 2. This

option is set to Nominal by default.

NOTE: This option is only available on certain stock keeping units (SKUs) of the processors.

x2APIC Mode Enables or disables the x2APIC mode. This option is set to Enabled by default.

Number of Cores

per Processor

Controls the number of enabled cores in each processor. This option is set to All by default.

Processor Core

Speed

Specifies the maximum core frequency of the processor.

Processor Bus

Speed

Displays the bus speed of the processor.

Processor n

NOTE: Depending on the number of processors, there might be up to two processors listed.

The following settings are displayed for each processor that is installed in the system:

Option Description

Family-Model-

Stepping

Specifies the family, model, and stepping of the processor as defined by Intel.

Brand Specifies the brand name.

Level 2 Cache Specifies the total L2 cache.

Level 3 Cache Specifies the total L3 cache.

Number of Cores Specifies the number of cores per processor.

Maximum

Memory Capacity

Specifies the maximum memory capacity per processor.

Microcode Specifies the microcode.

10 Pre-operating system management applications

SATA Settings

You can use the SATA Settings screen to view the settings of SATA devices and enable SATA and PCIe NVMe RAID mode on

your system.

Viewing SATA Settings

To view the SATA Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click SATA Settings.

SATA Settings details

About this task

The SATA Settings screen details are explained as follows:

Option

Description

Embedded SATA Enables the embedded SATA option to be set to Off, or AHCI Mode, or RAID Mode. This option is set to

AHCI Mode by default.

Security Freeze

Lock

Enables you to send Security Freeze Lock command to the embedded SATA drives during POST. This

option is applicable only for AHCI mode. This option is set to Enabled by default.

Write Cache Enables or disables the command for the embedded SATA drives during POST. This option is set to

Disabled by default.

Port n Enables you to set the drive type of the selected device.

For AHCI Mode or RAID Mode, BIOS support is always enabled.

Option Description

Model Specifies the drive model of the selected device.

Drive Type Specifies the type of drive attached to the SATA port.

Capacity Specifies the total capacity of the drive. This field is undefined for removable media

devices such as optical drives.

NVMe Settings

The NVMe settings enable you to set the NVMe drives to either RAID mode or Non-RAID mode.

NOTE:

To configure these drives as RAID drives, you must set the NVMe drives and the Embedded SATA option in the

SATA Settings menu to RAID mode. If not, you must set this field to Non-RAID mode.

Pre-operating system management applications 11

Viewing NVMe Settings

To view the NVMe Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE: If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click NVMe Settings.

NVMe Settings details

About this task

The NVMe Settings screen details are explained as follows:

Option

Description

NVMe Mode Enables you to set the NVMe mode. This option is set to Non RAID by default.

Boot Settings

You can use the Boot Settings screen to set the boot mode to either BIOS or UEFI. It also enables you to specify the boot

order.

● UEFI: The Unified Extensible Firmware Interface (UEFI) is a new interface between operating systems and platform

firmware. The interface consists of data tables with platform related information, boot and runtime service calls that are

available to the operating system and its loader. The following benefits are available when the Boot Mode is set to UEFI:

○ Support for drive partitions larger than 2 TB.

○ Enhanced security (e.g., UEFI Secure Boot).

○ Faster boot time.

NOTE: You must use only the UEFI boot mode in order to boot from NVMe drives.

● BIOS: The BIOS Boot Mode is the legacy boot mode. It is maintained for backward compatibility.

Viewing Boot Settings

To view the Boot Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Boot Settings.

Pre-operating system management applications

Boot Settings details

About this task

The Boot Settings screen details are explained as follows:

Option Description

Boot Mode Enables you to set the boot mode of the system.

CAUTION: Switching the boot mode may prevent the system from booting if the operating

system is not installed in the same boot mode.

If the operating system supports UEFI, you can set this option to UEFI. Setting this field to BIOS enables

compatibility with non-UEFI operating systems. This option is set to UEFI by default.

NOTE: Setting this field to UEFI disables the BIOS Boot Settings menu.

Boot Sequence

Retry

Enables or disables the Boot Sequence Retry feature or resets the system. If the last attempt to boot

has failed, the system immediately performs a cold reset or retries to boot after a 30 seconds, depending

on if this field is set to Reset or Enabled.This option is set to Enabled by default.

Hard-Disk

Failover

Specifies the drive that is booted in the event of a drive failure. The devices are selected in the Hard-

Disk Drive Sequence on the Boot Option Setting menu. When this option is set to Disabled, only the

first drive in the list is attempted to boot. When this option is set to Enabled, all drives are attempted to

boot in the order selected in the Hard-Disk Drive Sequence. This option is not enabled for UEFI Boot

Mode. This option is set to Disabled by default.

Generic USB

Boot

Enables or disables the USB boot option. This option is set to Disabled by default.

Hard-disk Drive

Placeholder

Enables or disables the Hard-disk drive placeholder option. This option is set to Disabled by default.

BIOS Boot

Settings

Enables or disables BIOS boot options.

NOTE: This option is enabled only if the boot mode is BIOS.

UEFI Boot

Settings

Enables or disables UEFI Boot options.

The Boot options include IPv4 PXE and IPv6 PXE. This option is set to IPv4 by default.

NOTE: This option is enabled only if the boot mode is UEFI.

UEFI Boot

Sequence

Enables you to change the boot device order.

Boot Options

Enable/Disable

Enables you to select the enabled or disabled boot devices.

Choosing system boot mode

System Setup enables you to specify one of the following boot modes for installing your operating system:

● BIOS boot mode is the standard BIOS-level boot interface.

● UEFI boot mode (the default), is an enhanced 64-bit boot interface.

If you have configured your system to boot to UEFI mode, it replaces the system BIOS.

1. From the System Setup Main Menu, click Boot Settings, and select Boot Mode.

2. Select the UEFI boot mode you want the system to boot into.

CAUTION:

Switching the boot mode may prevent the system from booting if the operating system is not

installed in the same boot mode.

3. After the system boots in the specified boot mode, proceed to install your operating system from that mode.

NOTE:

Operating systems must be UEFI-compatible to be installed from the UEFI boot mode. DOS and 32-bit operating

systems do not support UEFI and can only be installed from the BIOS boot mode.

Pre-operating system management applications 13

NOTE: For the latest information about supported operating systems, go to www.dell.com/ossupport.

Changing boot order

About this task

You may have to change the boot order if you want to boot from a USB key. You may have to change the boot order if you want

to boot from a USB key or an optical drive. The following instructions may vary if you have selected BIOS for Boot Mode.

Steps

1. On the System Setup Main Menu screen, click System BIOS > Boot Settings > UEFI/BIOS Boot Settings > UEFI/

BIOS Boot Sequence.

2. Click Boot Option Settings > BIOS/UEFI Boot Settings > Boot Sequence.

NOTE: Use the arrow keys to select a boot device, and use the plus (+) and minus (-) sign keys to move the device

down or up in the order.

3. Click Exit, and then click Yes to save the settings on exit.

Network Settings

You can use the Network Settings screen to modify UEFI PXE, iSCSI, and HTTP boot settings. The network settings option is

available only in the UEFI mode.

NOTE:

BIOS does not control network settings in the BIOS mode. For the BIOS boot mode, the optional Boot ROM of the

network controllers handles the network settings.

Viewing Network Settings

To view the Network Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Network Settings.

Network Settings screen details

The Network Settings screen details are explained as follows:

About this task

Option

Description

UEFI PXE

Settings

Options Description

PXE Device n (n

= 1 to 4)

Enables or disables the device. When enabled, a UEFI PXE boot option is created

for the device.

14 Pre-operating system management applications

Option Description

PXE Device n

Settings(n = 1 to

Enables you to control the configuration of the PXE device.

UEFI HTTP

Settings

Options Description

HTTP Device (n =

1 to 4)

Enables or disables the device. When enabled, a UEFI HTTP boot option is created

for the device.

HTTP Device n

Settings (n = 1 to

Enables you to control the configuration of the HTTP device.

UEFI iSCSI

Settings

Enables you to control the configuration of the iSCSI device.

Table 1. UEFI iSCSI Settings screen details

Option Description

iSCSI Initiator Name Specifies the name of the iSCSI initiator in IQN

format.

iSCSI Device1 Enables or disables the iSCSI device. When

disabled, a UEFI boot option is created for the

iSCSI device automatically. This is set to

Disabled by default.

iSCSI Device1 Settings Enables you to control the configuration of the

iSCSI device.

TLS

Authentication

Configuration

View and/or modify this device's boot TLS authentication mode. None means the HTTP server and the

client will not authenticate each other for this boot. One way means the HTTP server will be

authenticated by the client, while the client will not be authenticated by the server. This option is set to

None by default.

Integrated Devices

You can use the Integrated Devices screen to view and configure the settings of all integrated devices including the video

controller, integrated RAID controller, and the USB ports.

Viewing Integrated Devices

To view the Integrated Devices screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Integrated Devices.

Pre-operating system management applications

Integrated Devices details

About this task

The Integrated Devices screen details are explained as follows:

Option Description

User Accessible

USB Ports

Configures the user accessible USB ports. Selecting Only Back Ports On disables the front USB ports;

selecting All Ports Off disables all front and back USB ports; selecting All Ports Off (Dynamic)

disables all front and back USB ports during POST and front ports can be enabled or disabled dynamically

by an authorized user or authorized users without resetting the system.

The USB keyboard and mouse function in certain USB ports during the boot process, depending on the

selection. After the boot process is complete, the USB ports will be enabled or disabled as per the setting.

Internal USB

Port

Enables or disables the internal USB port. This option is set to On or Off. This option is set to On by

default.

NOTE: The Internal SD Card Port on the PCIe riser is controlled by Internal USB Port.

iDRAC Direct

USB Port

The iDRAC Direct USB port is managed by iDRAC exclusively with no host visibility. This option is set to

ON or OFF. When set to OFF, iDRAC does not detect any USB devices installed in this managed port.

This option is set to On by default.

Embedded NIC1

and NIC2

Enables or disables the OS interface of the embedded NIC1 and NIC2 Controller.

NOTE: If set to Disabled (OS), the embedded NICs may still be available for shared network access

by the embedded management controller. This function must be configured via the NIC management

utilities provided with your system.

NOTE: The LOM (Broadcom 57416) is compatible with 10GBASE-T IEEE 802.3an and 1000 BASE-T

IEEE 802.3ab.

I/OAT DMA

Engine

Enables or disables the I/O Acceleration Technology (I/OAT) option. I/OAT is a set of DMA features

designed to accelerate network traffic and lower CPU utilization. Enable only if the hardware and

software support the feature.This option is set to Disabled by default.

I/O Snoop

HoldOff

Response

Selects the number of cycles PCI I/O can withhold snoop requests, from the CPU, to allow time to

complete its own write to LLC. This setting can help improve performance on workloads where

throughput and latency are critical.

Embedded Video

Controller

Enables or disables the use of Embedded Video Controller as the primary display. When set to Enabled,

the Embedded Video Controller is used as the primary display even if add-in graphic cards are installed.

When set to Disabled, an add-in graphics card is used as the primary display. BIOS will output displays to

both the primary add-in video and the embedded video during POST and pre-boot environment. The

embedded video is disabled before the operating system boots. This option is set to Enabled by default.

NOTE: When there are multiple add-in graphic cards installed in the system, the first card discovered

during PCI enumeration is selected as the primary video. You might have to re-arrange the cards in

the slots in order to control which card is the primary video.

Current State of

Embedded Video

Controller

Displays the current state of the embedded video controller. The Current State of Embedded Video

Controller option is a read-only field. If the Embedded Video Controller is the only display capability in the

system (that is, no add-in graphics card is installed), then the Embedded Video Controller is automatically

used as the primary display even if the Embedded Video Controller setting is set to Enabled.

SR-IOV Global

Enable

Enables or disables the BIOS configuration of Single Root I/O Virtualization (SR-IOV) devices. This option

is set to Disabled by default.

OS Watchdog

Timer

If your system stops responding, this watchdog timer aids in the recovery of your operating system. When

this option is set to Enabled, the operating system initializes the timer. When this option is set to

Disabled (the default), the timer does not have any effect on the system.

Empty Slot

Unhide

Enables or disables the root ports of all the empty slots that are accessible to the BIOS and OS. This

option is set to Disabled by default.

Memory Mapped

I/O above 4 GB

Enables or disables the support for the PCIe devices that need large amounts of memory. Enable this

option only for 64-bit operating systems. This option is set to Enabled by default.

16 Pre-operating system management applications

Option Description

Memory Mapped

I/O Base

When set to 12 TB, the system maps the MMIO base to 12 TB. Enable this option for an OS that requires

44 bit PCIe addressing. When set to 512 GB, the system maps the MMIO base to 512 GB, and reduces

the maximum support for memory to less than 512 GB. Enable this option only for the 4 GPU DGMA issue.

This option is set to 56 TB by default.

Slot Disablement Enables or disables the available PCIe slots on your system. The slot disablement feature controls the

configuration of the PCIe cards installed in the specified slot. Slots must be disabled only when the

installed peripheral card prevents booting into the operating system or causes delays in system startup. If

the slot is disabled, both the Option ROM and UEFI drivers are disabled. Only slots that are present on the

system are available for control.

Slot Bifurcation Allows Platform Default Bifurcation, Auto Discovery of Bifurcation and Manual Bifurcation

Control. The default is set to Platform Default Bifurcation. The slot bifurcation field is accessible

when set to Manual Bifurcation Control and is disabled when set to Platform Default Bifurcation or

Auto Discovery of Bifurcation.

Table 2. Slot Bifurcation

Option Description

Slot 1 Bifurcation

x16, x4, x8, x4 x4 x8 or x8 x4 x4 Bifurcation

Slot 2 Bifurcation

x4 (Display only)

Slot 3 Bifurcation

x16, x4, x8, x4 x4 x8 or x8 x4 x4 Bifurcation

Slot 4 Bifurcation

x4 or x8 Bifurcation

Slot 5 Bifurcation

x4 (Display only)

Slot 6 Bifurcation

x16, x4, x8, x4 x4 x8 or x8 x4 x4 Bifurcation

Slot 7 Bifurcation

x4 or x8 Bifurcation

Slot 8 Bifurcation

x16, x4, x8, x4 x4 x8 or x8 x4 x4 Bifurcation

Serial Communication

You can use the Serial Communication screen to view the properties of the serial communication port.

Viewing Serial Communication

To view the Serial Communication screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click Serial Communication.

Pre-operating system management applications

Serial Communication details

About this task

The Serial Communication screen details are explained as follows:

Option Description

Serial

Communication

Enables you to select serial communication devices (Serial Device 1 and Serial Device 2) in BIOS. BIOS

console redirection can also be enabled, and the port address can be specified. This option is set to Auto

by default.

Serial Port

Address

Enables you to set the port address for serial device. This field sets the serial port address to either

COM1 or COM2 (COM1=0x3F8, COM2=0x2F8). This option is set to Serial Device1=COM2 or Serial

Device 2=COM1 by default.

NOTE: You can use only Serial Device 2 for the Serial Over LAN (SOL) feature. To use console

redirection by SOL, configure the same port address for console redirection and the serial device.

NOTE: Every time the system boots, the BIOS syncs the serial MUX setting saved in iDRAC. The

serial MUX setting can independently be changed in iDRAC. Loading the BIOS default settings from

within the BIOS setup utility may not always revert the serial MUX setting to the default setting of

Serial Device 1.

External Serial

Connector

Enables you to associate the External Serial Connector to Serial Device 1, Serial Device 2, or the

Remote Access Device by using this option. This option is set to Serial Device 1 by default.

NOTE: Only Serial Device 2 can be used for Serial Over LAN (SOL). To use console redirection by

SOL, configure the same port address for console redirection and the serial device.

NOTE: Every time the system boots, the BIOS syncs the serial MUX setting saved in iDRAC. The

serial MUX setting can independently be changed in iDRAC. Loading the BIOS default settings from

within the BIOS setup utility may not always revert this setting to the default setting of Serial Device

Failsafe Baud

Rate

Specifies the failsafe baud rate for console redirection. The BIOS attempts to determine the baud rate

automatically. This failsafe baud rate is used only if the attempt fails, and the value must not be changed.

This option is set to 115200 by default.

Remote Terminal

Type

Enables you to set the remote console terminal type. This option is set to VT100/VT220 by default.

Redirection After

Boot

Enables or disables the BIOS console redirection when the operating system is loaded. This option is set

to Enabled by default.

System Profile Settings

You can use the System Profile Settings screen to enable specific system performance settings such as power management.

Viewing System Profile Settings

To view the System Profile Settings screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

18 Pre-operating system management applications

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click System Profile Settings.

System Profile Settings details

About this task

The System Profile Settings screen details are explained as follows:

Option Description

System Profile Sets the system profile. If you set the System Profile option to a mode other than Custom, the BIOS

automatically sets the rest of the options. You can only change the rest of the options if the mode is set

to Custom.This option is set to Performance Per Watt Optimized (DAPC) by default. DAPC is Dell

Active Power Controller.

NOTE: All the parameters on the system profile setting screen are available only when the System

Profile option is set to Custom.

CPU Power

Management

Sets the CPU power management. This option is set to System DBPM (DAPC) by default. DBPM is

Demand-Based Power Management.

Memory

Frequency

Sets the speed of the system memory. You can select Maximum Performance, Maximum Reliability,

or a specific speed. This option is set to Maximum Performance by default.

Turbo Boost Enables or disables the processor to operate in the turbo boost mode. This option is set to Enabled by

default.

C1E Enables or disables the processor to switch to a minimum performance state when it is idle. This option is

set to Enabled by default.

C States Enables or disables the processor to operate in all available power states. This option is set to Enabled by

default.

Write Data CRC Enables or disables the Write Data CRC. This option is set to Disabled by default.

Memory Patrol

Scrub

Sets the memory patrol scrub frequency. This option is set to Standard by default.

Memory Refresh

Rate

Sets the memory refresh rate to either 1x or 2x. This option is set to 1x by default.

Uncore

Frequency

Enables you to select the Processor Uncore Frequency option.Dynamic mode enables the processor

to optimize power resources across cores and uncores during runtime. The optimization of the uncore

frequency to either save power or optimize performance is influenced by the setting of the Energy

Efficiency Policy option.

Energy Efficient

Policy

Enables you to select the Energy Efficient Policy option.

The CPU uses the setting to manipulate the internal behavior of the processor and determines whether to

target higher performance or better power savings. This option is set to Balanced Performance by

default.

Number of Turbo

Boost Enabled

Cores for

Processor 1

NOTE: If there are two processors installed in the system, you will see an entry for Number of

Turbo Boost Enabled Cores for Processor 2.

Controls the number of turbo boost enabled cores for Processor 1. The maximum number of cores is All

by default.

Monitor/Mwait Enables the Monitor/Mwait instructions in the processor. This option is set to Enabled for all system

profiles, except Custom by default.

NOTE: This option can be disabled only if the C States option in the Custom mode is set to

disabled.

NOTE: When C States is set to Enabled in the Custom mode, changing the Monitor/Mwait setting

does not impact the system power or performance.

CPU

Interconnect Bus

Enables or disables the CPU Interconnect Bus Link Power Management. This option is set to Enabled by

default.

Pre-operating system management applications 19

Option Description

Link Power

Management

PCI ASPM L1 Link

Power

Management

Enables or disables the PCI ASPM L1 Link Power Management. This option is set to Enabled by default.

System Security

You can use the System Security screen to perform specific functions such as setting the system password, setup password

and disabling the power button.

Viewing System Security

To view the System Security screen, perform the following steps:

Steps

1. Power on, or restart your system.

2. Press F2 immediately after you see the following message:

F2 = System Setup

NOTE:

If your operating system begins to load before you press F2, wait for the system to finish booting, and then

restart your system and try again.

3. On the System Setup Main Menu screen, click System BIOS.

4. On the System BIOS screen, click System Security.

System Security Settings details

About this task

The System Security Settings screen details are explained as follows:

Option

Description

CPU AES-NI Improves the speed of applications by performing encryption and decryption by using the Advanced

Encryption Standard Instruction Set (AES-NI). This option is set to Enabled by default.

System

Password

Enables you to set the system password. This option is set to Enabled by default and is read-only if the

password jumper is not installed in the system.

Setup Password Enables you to set the system setup password. This option is read-only if the password jumper is not

installed in the system.

Password Status Enables you to lock the system password. This option is set to Unlocked by default.

TPM Security

NOTE: The TPM menu is available only when the TPM module is installed.

Enables you to control the reporting mode of the TPM. The TPM Security option is set to Off by

default. You can only modify the TPM Status TPM Activation, and the Intel TXT fields if the TPM Status

field is set to either On with Pre-boot Measurements or On without Pre-boot Measurements.

When TPM 1.2 is installed, the TPM Security option is set to Off, On with Pre-boot Measurements,

or On without Pre-boot Measurements.

20 Pre-operating system management applications

Page is loading ...

Dell PowerEdge T640 Reference guide

Dell PowerEdge T640 Reference guide

Dell PowerEdge T640 Reference guide

Related papers

Other documents