VAS XL50-5GB Assembly Manual

Model # XL50-5GB

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.

PLEASE READ AND KEEP FOR FUTURE REFERENCE.

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 1

50” 3-in-1 Console

Option 1: Console with Swinging Floater

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if you are missing parts, do not return this item

to the Retailer Store. Please call our toll free customer service number and have your

instructions and parts list ready to provide the model name, part name or factory number:

1-866-942-5362 8:30 a.m. - 4:30 p.m. PST, Monday - Friday

ONLINE: www.whalenfurniture.com EMAIL: [email protected]

Video Instruction Guides

Go to http://whalen.showuhow.com to view step-by-step instructional

videos for assembling and installing your product. Enter the following

product number on the ShowUhow homepage.

LOT No.:

DATE OF PURCHASE:

XL50-5GB

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 2

QUALITY GUARANTEE

We are confident that you will be delighted with your VAS Furniture purchase.

Should this product be defective in workmanship or materials or fail under

normal use, we will repair or replace it for up to 1 year from date of purchase.

Every VAS Furniture product is designed to meet your highest expectations.

We guarantee that you will immediately see the value of our fine furniture.

This warranty gives you specific legal rights and you may also have other

rights which vary from State to State.

Customer Service: 1-866-942-5362

8:30 a.m. - 4:30 p.m. PST Monday to Friday

www.whalenfurniture.com

MANUFACTURER: VAS FURNITURE

CATALOG: 50” 3-in-1 Console (XL50-5GB)

DATE OF MANUFACTURE: September 2009

MADE IN CHINA

FITS UP TO MOST 56” FLAT PANEL TV’S

MAXIMUM LOAD 135 LBS

FITS UP TO MOST 56” FLAT PANEL TV’S WITHOUT

SWIVELING BRACKET

MAXIMUM LOAD 135 LBS

MAXIMUM LOAD 50 LBS

This unit is intended for use only with the products and maximum

weights indicated. Use with other products or products heavier than the maximum weights

indicated may result in instability causing possible injury. The base of the television must

be placed squarely in the center of the stand with no overhanging on either side.

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 3

Parts List

Please read completely through the instructions and verify that all parts listed are

present before beginning assembly.

A-Top Shelf Frame (1) B- Middle Shelf Frame (1)

C- Bottom Shelf Frame (1) D- Long Spine (1)

E- Left Leg (1) F- Right Leg (1) G- Top Glass (1)

H- Middle Glass Shelf (1) I- Bottom Glass Shelf (1) J- Swiveling Bracket (1)

K- XYZ Mounting Frame (1) L- Monitor Bracket (2) M- Safety Bar (1)

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 4

Hardware List

Please read completely through the instructions and verify that all parts listed are

present before beginning assembly.

(1)- Suction Cup (16+1 extra) (2) - 3/4” Bolt (24+1 extra) (3) - 1 1/4” Bolt (6+1 extra)

(4)- Nut (5) - Lock Washer (6) - Flat Washer (7) - Glass Raiser

(4+1 extra) (30+1 extra) (34+1 extra) (8)

Open Wrench (1) Allen Wrench (1) Tipping Restraint Hardware Kit (1)

(Inside Plastic Bag)

TV Mounting Kit

M4 x 12 Bolt (4) M4 x 30 Bolt (4) M5 X 12 Bolt (4) M5 x 30 Bolt (4)

M6 x12 Bolt (4) M6 x 35 Bolt (4) M8x16 Bolt (4) M8 x40 Bolt (4)

M4 Lock Washer (4) M5 Lock Washer (4) M6 Lock Washer (4) M8 Lock Washer (4)

Large Spacer (4) Small Spacer (4) M4/M5 Flat Washer (8) M6/M8 Flat Washer (4)

Tools Required: Allen Wrench (provided), Open Wrench (provided) and Phillips Screwdriver.

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 5

Assembly Instructions

Note: Please do not fully tighten all bolts until you finish assembling all parts, then go

back and fully tighten all bolts, this will make it easier during assembly of unit.

1. Unpack the unit and confirm that you have all the hardware and required parts listed.

2. Locate Long Spine (D) and set back face down on a scratch free surface as shown in detail

#1.

3. Align the holes on “U” shape plate of three Shelf Frames (A, B & C) with the threaded

inserts on the Long Spine (D) in place, insert and screw 3/4” Bolts (2) through Lock

Washers & Flat Washers (5 & 6) through the bracket holes into the Spine. See detail #1.

Required hardware in this step

No.

2

5

6

Sketch

Description

3/4” Bolt

Lock Washer

Flat Washer

Qty.

10pcs

Tools required

Allen Wrench

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 6

Assembly Instructions

4. Stand the unit upright.

5. Pick up Left Leg (E) and attach to the Middle & Bottom Shelf Frame (B & C) by inserting the

1 1/4” Bolts (3) with Washers (5 & 6) from inside the shelf frame through the pre-drilled

holes on side rail into the threaded inserts on Leg. See detail #2. DO NOT tighten the bolts.

6. Proceed to attach the Left Leg (E) to Top Shelf Frame (A) using two 3/4” Bolts (2) with

Washers (5 & 6) through the end bracket into the Leg. See detail #2A.

7. Repeat last two steps to install Right Leg (F) at the other end.

Required hardware in this step

No.

2

3

5

6

Sketch

Description

3/4” Bolt

1 1/4” Bolt

Lock Washer

Flat Washer

Qty.

4pcs

6pcs

10pcs

Tools required

Allen Wrench

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 7

Assembly Instructions

8. Go back and tighten all bolts with Allen Wrench provided.

9. In case of uneven floor, Floor Levelers are provided at the bottom of both Legs (E & F).

Simply tilt the unit back and raise or lower floor leveler by hand to correct tilting as shown in

detail #3.

Parts Provided Tools Required

Pre-attached Floor Leveler No Tool Required

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 8

Assembly Instructions

10. Align and attach Swiveling Bracket (J) to the top of Spine (D) using six 3/4” Bolts (2) with

Washers (5 & 6). Make sure the swivel bolt head is up. See detail #4.

Note: The Spine can provide four height options for your TV set. Refer to your TV size, adjust

the Swiveling Bracket at your desired height to offer optimum viewing.

Required hardware in this step

No.

2

5

6

Sketch

Description

3/4” Bolt

Lock Washer

Flat Washer

Qty.

6pcs

Tools required

Allen Wrench

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 9

Assembly Instructions

11. Hold the flat side of XYZ Mounting Frame (K) onto the Swiveling Bracket (J) ensuring the

hook on the side of Mounting Frame is bottom. Align and attach by threading four 3/4” Bolts

(2) with Flat Washers (6) through the metal plate on XYZ Mounting Frame and the Swiveling

Bracket, at the other side of Swiveling Bracket place the other Flat Washers (6) and Lock

Washers (5), and then secure with Nuts (4). Securely tighten with Open Wrench and Allen

Wrench provided. See detail #5.

Required hardware in this step

No.

2

4

5

6

Sketch

Description

3/4” Bolt

Nut

Lock Washer

Flat Washer

Qty.

4pcs

8pcs

Tools required

Allen Wrench, Open Wrench

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 10

Mounting Monitor Bracket to a television with a flat back

Note: For televisions with a curved back or recessed back proceed directly to step #15.

12. Determine the correct diameter of the bolt your TV requires by hand threading them into the

threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If

you are unable to find the correct bolt consult a local hardware store.

13. Once you have determined the correct diameter Bolt, follow the appropriate Diagram below,

thread the Short Bolt through the appropriate Lock Washer, Flat Washer, the Monitor Bracket

(L), and into the upper threaded inserts of TV. As shown in detail #6A. Note: Lean the TV up

against a wall or other solid surface when attaching with the Monitor Brackets (L). DO NOT

place the TV face down on the glass this may cause permanent damage.

14. Proceed to insert the long Bolt through the appropriate Lock Washer, the Flat Washer, the slot

of Monitor Bracket (L), a second Flat Washer (M4/M5 Diameter Bolts only), appropriate

Spacer, and into the bottom threaded inserts of TV. As shown in detail #6. Make sure the

Monitor Brackets (L) are centered and level with each other. Tighten the bolts securing the

Monitor Brackets to the TV.

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 11

Mounting Monitor Bracket to a television with a curved / recess back

15. Determine the correct diameter of the bolt your TV requires by hand threading them into the

threaded insert on the back of the TV. If you encounter any resistance, stop immediately. If

you are unable to find the correct bolt consult a local hardware store.

16. Once you have determined the correct diameter Bolt, follow the appropriate Diagram below,

thread the Bolt through the appropriate Lock Washer, Flat Washer, the Monitor Bracket (L), a

second Flat Washer (M4/M5 Diameter Bolts only), appropriate Spacer and into the threaded

inserts of TV. See detail #7.

17. Make sure the Monitor Brackets (L) are vertically centered and level with each other. Tighten

the bolts securing the Monitor Brackets to the TV.

Parts Provided Qty Tools Required

L – Monitor Bracket (2) Phillips Screwdriver

TV Mounting Kit

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 12

Assembly Instructions

MAKE SURE ALL BOLTS ARE TIGHT AND SPINE IS AT A 90 DEGREE ANGLE

PRIOR TO INSTALLATION OF TV.

18. Once the Monitor Brackets (L) are attached onto the back of television, ask for assistance to

lift the television up to the XYZ Mounting Frame (K). Place the hooks on Monitor Brackets

over the Mounting Frame then lower them onto the bars of Mounting Frame. Proceed to

center the television.

19. Insert the Safety Bar (M) into the bottom holes on the side of XYZ Mounting Frame (K) by

sliding it all the way across the frame. Secure the Safety Bar by rotating the bent end into the

slot of hook so that it is facing back of unit. Make sure it sits over the bottom hook of the

Monitor Brackets. See detail #8.

Parts Required Qty Tools Required

M– Safety Bar (1) No Tool Required

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 13

Assembly Instructions

20. Put the Suction Cups (1) firmly into top holes of the Middle Shelf Frame (B) & Bottom Shelf

Frame (C) as shown in detail #9.

21. Screw the Glass Raisers (7) onto the top holes of Top Shelf Frame (A), make sure they go all

the way in. See detail #9.

22. Place the Top Glass (G) & Glass Shelves (H & I) in place as shown in detail #9. Push each

glass all the way back against the Spine. Make sure the glass sits correctly and is properly

centered. Also, be sure to press down evenly and firmly each shelf onto the Suction Cups to

make sure they securely rest onto the Suction Cups.

Note: Make sure that the Suction Cups go all the way into the pre-drilled holes to prevent

the glass shelf from falling and getting damage. If glass is scratched you can minimize the

damage by using a BLACK marker and filling in scratched area from underneath.

Required hardware in this step

No.

1

7

Sketch

Description

Suction Cup

Glass Raiser

Qty.

16pcs

8pcs

Tools required

No tool required

Model # XL50-5GB

Please call for replacement parts or assistance: 1-866-942-5362

VAS Furniture Mfg. Inc. Factory No. 56-12089 Page 14

TIPPING RESTRAINT HARDWARE

Note: We have included one Tipping Restraint Hardware bag for this Unit.

When properly installed, this restraint can provide protection against the unexpected tipping

of the Unit due to small tremors, bumps or climbing. We strongly recommend mounting this

hardware to a wall stud and your unit when installing.

Please carefully read the instructions printed on the plastic bag.

Note: You must install the Tipping Restraint Hardware with the unit in use to prevent

any accidents or damage to the unit.

Tools Required: Allen Wrench (provided), Phillips Screwdriver, Mallet, Power Drill, and 3/8” Drill Bit.

Your assembly should now be complete.

Thank you for your purchase.

VAS XL50-5GB Assembly Manual

VAS XL50-5GB Assembly Manual

Related papers

Other documents