![](//vs1.manuzoid.com/store/data-gzf/c657212f25aa0a20fc4b2d807786a9ca/2/001953077.htmlex.zip/bg2.jpg)
Prewash cycle increases programme duration by approx. 15 minutes.
Consumption data were measured in normalised conditions in compliance with Standard IEC 60456.
Consumption data in the home may vary with respect to the values in the table in relation to the water supply pres-
sure and temperature, the load and the type of wash.
ROUTINE WASHES:
1. Turn on the tap.
2. Sort the laundry according to fabric type and colour and load the machine.
3. Close the door.
4. Pour in detergent and additives.
5. Select the programme, the temperature and any special options you require.
6. Hold down the “Start” button for about one second.
NOTE:
During the first 15 minutes of Cotton and Easy Care programmes (each without Prewash)
you can open the door to add items to the wash. This is not possible when the special
function “Short” is selected.
TO INTERRUPT THE PROGRAMME:
To interrupt a programme that is already running and then continue later:
1. Set the programme selector knob to “0”.
2. After the required break, reselect the programme.
3. Hold down the “Start” button for about one second.
The programme will continue from where it was interrupted.
CHANGING PROGRAMME DURING A RUNNING PROGRAMME:
a) TO SELECT A NEW PROGRAMME OR A DIFFERENT TEMPERATURE AND
CONTINUE
1. Select a new programme and/or new temperature.
2. Hold down the “Start” button for about one second.
The new programme will continue from the same programme step where the running
programme was interrupted.
b) TO CANCEL A PROGRAMME THAT IS ALREADY RUNNING AND START A
DIFFERENT PROGRAMME FROM THE BEGINNING
There’s no need to add more detergent when you start the new programme, because
the appliance drains only just few water when you cancel the current programme.
1. Hold down the “Start” button for five seconds, or until the programme control
audibly restarts.
2. Wait until the programme sequence indicator returns to its initial position on the left
(no longer visible).
3. Set the programme selector to “0”.
4. Set the programme selector knob to the new programme, select the temperature
(if different) and any different special options you require.
5. Hold down the “Start” button for about one second.
TROUBLESHOOTING GUIDE:
The appliance is equipped with safety functions able to identify and indicate the presence of
faults and react appropriately.
Most faults are minor problems that can be solved quickly. The following list gives several
examples:
• The appliance fails to start.
• The appliance stops in mid programme.
• No water or insufficient water supply.
• The appliance does not drain.
• The machine vibrates during the spin cycle.
• Final spin results are poor.
• Detergent and additive product residues in the detergent dispenser at end of wash.
The cause and action notes for the above points are given in the instruction for use in the
chapter “Troubleshooting guide”.
Programme
Thermostat
knob
Maximum
load
Special
options
Water Electricity
Programme
duration
(°C) (kg) (l) (kWh) (min.)
Cotton/Cotton Coloured 95 5.0 — 60 1.70 115
Cotton/Cotton Coloured 60 5.0 — 56 1.10 110
Cotton/Cotton Coloured 60 5.0
Energy save /
Eco
56 0.55 105
Cotton/Cotton Coloured 60 2.5
Saving half
load
40 0.90 95
Cotton/Cotton Coloured 40 5.0 — 56 0.55 95
Cotton/Cotton Coloured 30 3.0 Short 35 0.30 40
Easy care 60 2.5 — 60 0.80 80
Easy care 40 2.5 — 54 0.40 70
Easy care 30 1.5 Short 25 0.20 35
Delicate 40 1.5 — 60 0.50 40
Wool 40 1.0 — 60 0.50 35
Power and water consumption data
GB