Bauknecht WA 4360 Program Chart

Type
Program Chart
1) For improved garment care, spin speed is restricted to 900 rpm.
2) The programme duration figures are approximate values for a programme with maximum temperature but without special options.
Programme Care label Type of fabric /
Degree of soiling
Max.
Load
Detergent
and Additives
Options =
Thermostat
knob
Programme
Selector
Programme
Duration
2)
Notes
Softener Main
Wash
Pre-
wash
Saving
half load
Rapid Intensive
Rinse
Rinse
Hold
Pre-
wash
Spinning
kg °C
approx.
Min.
Cotton/
Cotton
Coloured
Lightly to averagely soiled bed
linen, table linen, underwear,
towels, shirts etc. (linen and
cotton) etc.
Normal
5.0
Rapid
3.0
yes
❉❉❉❉❉❉❉
from cold
to 95
Rapid: From
cold to 60
Cotton/
Cotton
Coloured
115
60
If “Rapid” is selected the options “Saving half
load”, “Intensive Rinse” and “Prewash” are
inhibited.
If “Saving half load” is selected the option
“Intensive Rinse” is inhibited.
Synthetics
Lightly to averagely soiled
blouses, shirts, etc. made of
polyester (Diolen, Trevira),
polyamide (Perlon, Nylon) or
blends with cotton.
Normal
2.5
Rapid
1.5
yes
❉❉❉❉❉❉
1)
from cold
to 60
Rapid: from
cold to 60
Synthetics
70
45
If “Rapid” is selected the options “Saving half
load”, “Intensive Rinse” and “Prewash” are
inhibited.
If “Saving half load” is selected the option
“Intensive Rinse” is inhibited.
Delicates
Curtains, delicate dresses,
skirts, shirts and blouses.
1.5
yes
———
❉❉
1)
from cold
to 40
Delicates
40
Wool
Only machine washable woollens
with pure new wool label.
1.0
yes
————
1)
from cold
to 40
Wool
35
If you select the special option “Rinse Hold” don’t
leave garments to soak for too long.
Rinse + Spin 5.0
—————
Cold
Rinse + Spin
+
Programme for treating wash with starch or
softener. Terminates with an intensive spin
cycle, same as the spin cycle in the Cotton
Coloured programme.
Gentle Spin 5.0————————
1)
Gentle Spin
Programme for gentle spin cycle, same as the
spin cycle in the Wool programme.
Draining —————————
Draining
Drain only without spin cycle.
Alternative way of terminating programmes with
“Rinse hold” setting.
Indicator: Door lock
PROGRAMME TABLE
2B 4619 710 03621
is a registered trademark
GB
Indicator:
Wash Rinse Spin
WA 4360
Pre-wash cycle increases programme duration by approx. 15 minutes.
Consumption data were measured in normalised conditions in compliance with Standard IEC 456.
Consumption data in the home may vary with respect to the values in the table in relation to the water supply
pressure and temperature, the load and the type of wash.
ROUTINE WASHES:
1. Turn on the tap.
2. Sort the laundry according to fabric type and colour and load the machine.
3. Close the door.
4. Pour in detergent and additives.
5. Select the programme, the temperature and any special options you require.
6. Hold down the Start button for about one second.
NOTE:
During the first 15 minutes of Cotton and Synthetics programmes (each without Prewash)
you can open the door to add items to the wash. This is not possible when the special
function Rapid is selected.
TO INTERRUPT THE PROGRAMME:
To interrupt a programme that is already running and then continue later:
1. Set the programme selector knob to 0.
2. After the required break, reselect the programme.
3. Hold down the Start button for about one second.
The programme will continue from where it was interrupted.
CHANGING PROGRAMME DURING A RUNNING PROGRAMME:
a) TO SELECT A NEW PROGRAMME OR A DIFFERENT TEMPERATURE AND
CONTINUE
1. Select a new programme and/or new temperature.
2. Hold down the Start button for about one second.
The new programme will continue from the same programme step where the running
programme was interrupted.
b) TO CANCEL A PROGRAMME THAT IS ALREADY RUNNING AND START A
DIFFERENT PROGRAMME FROM THE BEGINNING
Theres no need to add more detergent when you start the new programme, because
the appliance drains only just few water when you cancel the current programme.
1. Hold down the Start button for five seconds, or until the programme control
audibly restarts.
2. Wait until the programme sequence indicator returns to its initial position on the left
(no longer visible).
3. Set the programme selector to 0.
4. Set the programme selector knob to the new programme, select the temperature
(if different) and any different special options you require.
5. Hold down the Start button for about one second.
TROUBLESHOOTING GUIDE:
The appliance is equipped with safety functions able to identify and indicate the presence
of faults and react appropriately.
Most faults are minor problems that can be solved quickly. The following list gives several
examples:
The appliance fails to start.
The appliance stops in mid programme.
No water or insufficient water supply.
The appliance does not drain.
The machine vibrates during the spin cycle.
Final spin results are poor.
Detergent and additive product residues in the detergent dispenser at end of wash.
The cause and action notes for the above points are given in the instruction for use in the
chapter Troubleshooting guide.
Programme
Thermostat
knob
Maximum
load
Special
options
Water Electricity
Programme
duration
(°C) (kg) (l) (kWh) (min.)
Cotton/Cotton Coloured 95 5 60 1.70 115
Cotton/Cotton Coloured 60 5 56 1.10 110
Cotton/Cotton Coloured 60 2.5
Saving half
load
40 0.90 95
Cotton/Cotton Coloured 40 5 56 0.55 95
Cotton/Cotton Coloured 30 3 Rapid 35 0.30 40
Synthetics 60 2.5 60 0.80 80
Synthetics 40 2.5 54 0.40 70
Synthetics 30 1.5 Rapid 25 0.20 35
Delicate 40 1.5 60 0.50 40
Wool 40 1 60 0.50 35
Power and water consumption data
GB
  • Page 1 1
  • Page 2 2

Bauknecht WA 4360 Program Chart

Type
Program Chart

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI