Panasonic PT-AE4000E Owner's manual
- Category
- Data projectors
- Type
- Owner's manual
Operating Instructions
LCD Projector
PT-AE4000E
Thank you for purchasing this Panasonic product.
Before operating this product, please read the instructions carefully, and save this manual for future use.
Please read the functional instructions that is in the provided CD-ROM for more details.
TQBJ0308
ENGLISH
Model No.
2 - ENGLISH
Important
Information
Important Safety Notice
Dear Panasonic Customer:
This instruction booklet provides all the necessary operating information that you might require. We hope it will
help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector.
The serial number of your product may be found on its bottom. You should note it in the space provided below and
retain this booklet in case service is required.
Model number: PT-AE4000E
Serial number:
WARNING: THIS APPARATUS MUST BE EARTHED.
WARNING: To prevent damage which may result in re or shock hazard, do not expose this appliance
to rain or moisture.
Machine Noise Information Ordinance 3. GSGV, January 18, 1991: The sound pressure level at the operator
position is equal or less than 70 dB (A) according to ISO 7779.
WARNING:
Remove the plug from the mains socket when this unit is not in use for a prolonged period of time.1.
To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualied 2.
service personnel.
Do not remove the earthing pin on the mains plug. This apparatus is equipped with a three prong earthing-type
3.
mains plug. This plug will only t an earthing-type mains socket. This is a safety feature. If you are unable to
insert the plug into the mains socket, contact an electrician. Do not defeat the purpose of the earthing plug.
Important Information
Information for Users on Collection and Disposal of Old Equipment and used
Batteries
These symbols on the products, packaging, and/or accompanying documents mean that used
electrical and electronic products and batteries should not be mixed with general household waste.
For proper treatment, recovery and recycling of old products and used batteries, please take them to
applicable collection points, in accordance with your national legislation and the Directives 2002/96/
EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable resources and
prevent any potential negative effects on human health and the environment which could otherwise
arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries, please contact your
local municipality, your waste disposal service or the point of sale where you purchased the items.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national
legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for
further information.
Information on Disposal in other Countries outside the European Union
These symbols are only valid in the European Union. If you wish to discard these items, please
contact your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it complies with the
requirement set by the Directive for the chemical involved.
Environment care information for users in China
This symbol is only valid in China.
Important Safety Notice
ENGLISH - 3
Important
Information
CAUTION: To assure continued compliance, follow the attached installation instructions, which includes
using the provided power cord and shielded interface cables when connecting to computer or
peripheral device. If you use serial port to connect PC for external control of projector, you must
use optional RS-232C serial interface cable with ferrite core. Any unauthorised changes or
modications to this equipment will void the user’s authority to operate.
Pursuant to at the directive 2004/108/EC, article 9(2)
Pursuant to at the directive 2005/32/EC amended by 2008/28/EC, article 14
Panasonic Testing Centre
Panasonic Service Europe, a division of Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany
IMPORTANT: THE MOULDED PLUG (U.K. only)
FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 13 amp fuse is
tted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 13
amps and that it is approved by ASTA or BSI to BS1362.
Check for the ASTA mark or the BSI mark on the body of the fuse.
If the plug contains a removable fuse cover, you must ensure that it is retted when the fuse is replaced. If you lose
the fuse cover, the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be
purchased from an Authorised Service Centre.
If the tted moulded plug is unsuitable for the mains socket in your home, then the fuse should be
removed and the plug cut off and disposed of safely. There is a danger of severe electrical shock if the cut
off plug is inserted into any 13 amp socket.
If a new plug is to be tted, please observe the wiring code as shown below.
If in any doubt, please consult a qualied electrician.
WARNING: THIS APPLIANCE MUST BE EARTHED.
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:
Green - and - Yellow:
Blue:
Brown:
Earth
Neutral
Live
As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows.
The wire which is coloured GREEN - AND - YELLOW must be connected to the terminal in the plug
which is marked with the letter E or by the Earth symbol or coloured GREEN or GREEN - AND -
YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked
with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal in the plug which is marked
with the letter L or coloured RED.
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.
13A250V BS1363/A
HE-8
N
ASA
L
4 - ENGLISH
Quick steps
J
Set up your projector1.
See “Setting up” on page 14.
Connect with other devices2.
See “Connections” on page 15.
Prepare the remote control3.
See “Remote control” on
page 11.
Start projecting4.
See “Switching the projector
on/off” on page 16.
Adjust the image5.
See “Menu Navigation” on
page 19.
PT-AE4000E includes the following
features and many more…
Lens Memory
Memorize focus/zoom position of the lens,
for easy transition between different aspect
contents (ex. 16:9 to 2.35:1).
With auto switching capability.
Waveform Monitor
Adjust the luminance level of the input signal
to display full dynamic range of the content.
VIERA Link
Control multiple Panasonic devices and other
CEC compatible devices via HDMI cable using
the projector remote.
Split Adjust Mode
Perform adjustments to the image by viewing
the before and after image side by side.
Consult the Functional Instructions included in
the CD-ROM for instructions on how to use these
features.
ENGLISH - 5
Important
Information
PreparationSettingsMaintenanceAppendix Getting
Started
Basic
Operation
Contents
Important Information
Important Safety Notice ................................ 2
Precautions with regard to safety ................ 6
WARNING .......................................................... 6
CAUTION ........................................................... 7
Cautions when transporting .................................. 8
Cautions when installing..................................... 8
Cautions on use ................................................. 9
Cleaning and maintenance................................. 9
Disposal.............................................................. 9
Accessories ...................................................... 10
Preparation
About Your Projector ................................... 11
Remote control ..................................................11
Projector body .................................................. 12
Getting Started
Setting up ..................................................... 14
Screen size and throw distance ....................... 14
Projection method ............................................ 14
Lens shift and positioning ................................. 15
Connections ................................................. 15
Before connecting to the projector ................... 15
Basic Operation
Switching the projector on/off .................... 16
Mains lead ........................................................ 16
Power indicator................................................. 16
Switching on the projector ................................ 17
Switching off the projector ................................ 17
Projecting an image ..................................... 18
Selecting the input signal ................................. 18
Positioning the image ....................................... 18
Settings
Menu Navigation .......................................... 19
Navigating through the MENU.......................... 19
Menu list ........................................................... 20
VIERA Link .................................................... 23
Using the Link functions (VIERA Link).............. 23
Maintenance
TEMP and LAMP Indicators ........................ 25
Managing the indicated problems .................... 25
Care and Replacement ................................ 26
Cleaning the projector ...................................... 26
Replacing the lamp unit .................................... 27
Troubleshooting ........................................... 29
Appendix
Technical Information .................................. 30
Ceiling mount bracket safeguards .................... 30
List of compatible signals ................................. 31
Specications ................................................... 32
Trademark acknowledgements ........................ 34
Dimensions....................................................... 34
Index ............................................................. 35
6 - ENGLISH
Important
Information
Precautions with regard to safety
WARNING
POWER
The mains socket or the circuit breaker shall
be installed near the equipment and shall
be easily accessible when problems occur.
If the following problems occur, cut off the
power supply immediately.
Continued use of the projector in these conditions will
result in re or electric shock.
If foreign objects or water get inside the projector,
z
cut off the power supply.
If the projector is dropped or the cabinet is broken,
z
cut off the power supply.
If you notice smoke, strange smells or noise coming
z
from the projector, cut off the power supply.
Please contact an Authorised Service Centre for repairs,
and do not attempt to repair the projector yourself.
During a thunderstorm, do not touch the
projector or the cable.
Electric shocks can result.
Do not do anything that might damage the
mains lead or the mains plug.
If the mains lead is used while damaged, electric
shocks, short-circuits or re will result.
Do not damage the mains lead, make any
z
modications to it, place it near any hot objects,
bend it excessively, twist it, pull it, place heavy
objects on top of it or wrap it into a bundle.
Ask an Authorised Service Centre to carry out any repairs
to the mains lead that might be necessary.
Insert the mains plug securely into the mains
socket.
If the plug is not inserted correctly, electric shocks or
overheating will result.
Do not use anything other than the provided mains
z
lead and ground in the mains socket.
Do not use plugs which are damaged or mains
z
sockets which are coming loose from the wall.
Clean the mains plug regularly to prevent it
from becoming covered in dust.
Failure to observe this will cause a re.
If dust builds up on the mains plug, the resulting
z
humidity can damage the insulation.
If not using the projector for an extended period of
z
time, pull the mains plug out from the mains socket.
Pull the mains plug out from the mains socket and wipe it
with a dry cloth regularly.
Do not handle the mains plug with wet hands.
Failure to observe this will result in electric shocks.
Do not overload the mains socket.
If the power supply is overloaded (ex., by using too
many adapters), overheating may occur and re will
result.
ON USE/INSTALLATION
Do not place liquid containers on top of the
projector.
If water spills onto the projector or gets inside it, re or
electric shocks will result.
If any water gets inside the projector, contact an
Authorised Service Centre.
Do not place the projector on soft materials
such as carpets or sponge mats.
Doing so will cause the projector to overheat, which can
cause burns, re or damage to the projector.
Do not set up the projector in humid or dusty
places or in places where the projector may
come into contact with oily smoke or steam,
ex., a bathroom.
Using the projector under such conditions will result
in re, electric shocks or components deterioration.
Components deterioration (such as ceiling mount
brackets) may cause the projector which is mounted on
the ceiling to fall down.
Do not install this projector in a place which
is not strong enough to take the full weight
of the projector or on top of a surface which
is sloped or unstable.
Failure to observe this will cause projector to fall down
or tip over the projector, and severe injury or damage
could result.
Do not place another projector or other
heavy objects on top of the projector.
Failure to observe this will cause the projector to
become unbalanced and fall, which could result in
damage or injury. The projector will be damaged or
deformed.
Installation work (
such as ceiling suspension
)
should only be carried out by a qualied
technician.
If installation is not carried out and secured correctly it
can cause injury or accidents, such as electric shocks.
Do not use anything other than an authorised
z
ceiling mount bracket.
Be sure to use the provided accessory wire as an
z
extra safety measure to prevent the projector from
falling down. (Install in a different location to the
ceiling mount bracket)
Do not cover the air inlet port or the air
outlet port.
Doing so will cause the projector to overheat, which can
cause re or damage to the projector.
Do not place the projector in narrow, badly
z
ventilated places such as closets or bookshelves.
Do not place the projector on cloth or papers, as
z
these materials could be drawn into the air inlet
port.
Precautions with regard to safety
ENGLISH - 7
Important
Information
Do not place your hands or other objects
close to the air outlet port.
Doing so will cause burns or damage your hands or
other objects.
Heated air comes out of the air outlet port. Do not
z
place your hands or face, or objects which cannot
withstand heat close to this port.
Do not look into or touch the lights emitted
from the lens while the projector is being used.
Doing so can cause burns or loss of sight.
Strong light is emitted from the projector’s lens. Do
z
not look or place your hands directly into this light.
Be especially careful not to let young children look
z
into the lens. In addition, turn off the power and
disconnect the mains plug when you are away from
the projector.
Do not insert any foreign objects into the
projector.
Doing so will cause re or electric shocks.
Do not insert any metal objects or ammable objects
z
into the projector or drop them onto the projector.
Never attempt to remodel or disassemble
the projector.
High voltages can cause re or electric shocks.
For any inspection, adjustment and repair work, please
contact an Authorised Service Centre.
Do not use the projector while the projection
lens cap is still attached to the projection lens.
If this is not observed, the lens cap will be damaged
and re will occur.
ACCESSORIES
Do not use or handle the batteries improperly,
and refer to the following.
Failure to observe this will cause burns, batteries to
leak, overheat, explode or catch re.
Do not use unspecied batteries.
z
Use manganese batteries or alkaline batteries.
z
Do not dissemble dry cell batteries.
z
Do not heat the batteries or place them into water
z
or re.
Do not allow the + and − terminals of the batteries
z
to come into contact with metallic objects such as
necklaces or hairpins.
Do not store batteries together with metallic objects.
z
Store the batteries in a plastic bag and keep them
z
away from metallic objects.
Make sure the polarities (+ and −) are correct when
z
inserting the batteries.
Do not use a new battery together with an old
z
battery or mix different types of batteries.
Do not use batteries with the outer cover peeling
z
away or removed.
Remove the empty batteries from the remote
z
control at once.
Insulate the battery using tape or something similar
z
before disposal.
Do not allow children to reach the batteries.
The battery can cause death by suffocation if
z
swallowed.
If swallowed, seek medical advice immediately.
z
If the battery uid leaks, do not touch it with
bare hands, and take the following measures
if necessary.
Battery uid on your skin or clothing could result in
z
skin inammation or injury.
Rinse with clean water and seek medical advice
immediately.
Battery uid coming in contact with your eyes could
z
result in loss of sight.
In this case, do not rub your eyes. Rinse with clean
water and seek medical advice immediately.
Do not disassemble the lamp unit.
If the lamp breaks, it could cause injury.
Lamp replacement
The lamp has high internal pressure. If improperly handled,
an explosion and severe injury or accidents will result.
Replacement of the lamp should be carried out by a
z
qualied technician.
The lamp can easily explode if struck against hard
z
objects or dropped.
Before replacing the lamp, be sure to disconnect
z
the mains plug from the mains socket.
Electric shocks or explosions can result if this is not
done.
When replacing the lamp, allow it to cool for at least
z
one hour before handling it otherwise it can cause
burns.
Do not allow infants or pets to touch the
remote control unit.
Keep the remote control unit out of the reach of
z
infants and pets after using it.
CAUTION
POWER
When disconnecting the mains lead, hold the
plug, not the lead.
If the mains lead itself is pulled, the lead will become
damaged, and re, short-circuits or serious electric
shocks will result.
When not using the projector for an
extended period of time, disconnect the
mains plug from the mains socket and
remove the batteries from the remote
control.
Disconnect the mains plug from the mains
socket before carrying out any cleaning.
Electric shocks can result if this is not done.
Precautions with regard to safety
8 - ENGLISH
Important
Information
ON USE/INSTALLATION
Do not put your weight on this projector.
You could fall or the projector could break, and injury
will result.
Be especially careful not to let young children stand
z
or sit on the projector.
Do not place the projector in extremely hot
locations.
Doing so will cause the outer casing or internal
components to deteriorate, or result in re.
Take particular care in locations exposed to direct
z
sunlight or near stoves.
Always disconnect all cables before moving
the projector.
Moving the projector with cables still attached can
damage the cables, which will cause re or electric
shocks to occur.
ACCESSORIES
Do not use the old lamp unit.
If used, it could cause lamp explosion.
If the lamp has broken, ventilate the room
immediately. Do not touch or bring your face
close to the broken pieces.
Failure to observe this will cause the user to absorb
the gas which was released when the lamp broke and
which contains nearly the same amount of mercury as
uorescent lamps, and the broken pieces will cause
injury.
If you believe that you have absorbed the gas or that the
gas has got into your eyes or mouth, seek medical advice
immediately.
Ask your dealer about replacing the lamp unit and check
the inside of the projector.
Do not place your hands in the openings
beside the optical lens, while shifting the lens.
Failure to observe this could cause injury.
Do not use projectors with the adjustable
feet or lens unit cover removed.
If this not observed, the sets will not operate correctly
or accidents will result.
Cautions when transporting
When transporting the projector or carrying it around,
make sure that the lens cap is always in place, and
remove the lens. Please take care to keep them away
from vibration and impacts, both the projector and
the lens are precision-made and easily susceptible to
damage.
When transporting the projector, the adjuster legs must
be housed and do not hold them. Please securely hold
only its bottom and none of its other parts or surfaces
as this will result in malfunctions.
Cautions when installing
Do not use under the following
conditions.
Do not set up the projector outdoors.
z
The projector is designed for indoor use only.
Avoid setting up in places which are subject to
z
vibration or shocks.
If the projector is installed in a place where
vibrations are transmitted or mounted in a car or a
vessel, vibrations or impacts will result in damage to
the internal parts, causing failure. Install the product
in a place free from vibrations and impacts.
Avoid setting up in places which are subject to
z
sudden temperature changes, such as near an
air conditioner or lighting equipment.
Failure to observe this will result in malfunctions or
the lamp life will be shortened.
See “TEMP indicator” on page 25.
Avoid setting up in places which are near high-
z
voltage power lines or near motors.
The product will be exposed to interference if it is
installed in the vicinity of high-voltage electrical
power lines or power sources.
Do not install the projector at elevations higher
z
than 2 700 m (8 858 ft) above sea level.
If using this projector at high elevations 1 400 -
2 700 m (4 593 - 8 858 ft) above sea level, set the
HIGH ALTITUDE MODE to ON.
Failure to observe this will result in malfunctions
or the lamp life or life of other components will be
shortened.
Be sure to ask a specialised
technician when installing the product
to a ceiling.
If the product is to be installed hanging from the ceiling,
purchase an optional hanging attachment (For high
ceilings: Model No. ET-PKE1000S, For low ceilings:
Model No. ET-PKE2000). Please call a specialised
technician or contact an Authorised Service Centre for
installation.
Be sure to put on the lens unit cover
after installing the projection lens.
If this not done, dust will collect inside the projector and
problems with the projector can result.
Lens Focus
Do not adjust the lens focus in the initial period after
switching the projector on. The high clarity projector
lens is thermally affected by the light from the light
source, making the focus unstable in the period just
after switching on. Please allow a warm-up time before
adjusting the lens focus.
Precautions with regard to safety
ENGLISH - 9
Important
Information
Cautions on use
In order to get the picture quality
Draw curtains or blinds over windows and turn off any
lights near the screen to prevent outside light or light
from indoor lamps from shining onto the screen.
Depending on where the projector is used, air exhaust
vents or the warm air from air conditioning can cause a
shimmering effect on the screen. For this reason, take
care not to shield the air exhaust vents and consider
the direction of the air owing from air conditioning.
Do not adjust the lens focus in the initial period
z
(within approx. 30 minutes) after switching the
projector on.
Do not touch the surface of the
projector lens with your bare hand.
If the surface of the lens becomes dirty from ngerprints
or anything else, this will be magnied and projected
onto the screen. Cover the lens with the lens cap when
the projector is not used.
The projector has a high pressure
mercury lamp that is characterised
as follows:
The brightness of the lamp will decrease over time.
z
The lamp may explode or shorten the lamp life by
z
shocks or chipping damage.
In rare cases, it may burst shortly after the rst use.
z
The possibility of its bursting increases when the
z
lamp is used beyond the replacement time.
If the lamp bursts, gas inside the lamp is released
z
in the form of smoke.
The life of a mercury lamp varies according to the
z
individual difference or conditions of use.
In particular, turning the power on and off frequently
z
and/or repeatedly as well as continuous use for
12 hours will greatly affect the life cycle. Provide a
lamp for replacement in advance.
Connection to external device
When connecting the projector to a computer or
external device, use the mains lead supplied with the
corresponding device and a commercially available
shielded interface cable.
Optical components
It may be necessary to replace the optical components
such as liquid crystal panels and polarizing plates
in less than 1 year if using the projector in a high
temperature environment or in a very dusty, oily smoke
or tobacco smoke environment. For more details,
please contact your dealer.
Liquid crystal panel
Do not project the same image for long periods of
time, as this may remain as an afterimage on the liquid
crystal panel. Display the white screen test pattern
for more than an hour to remove it. See the functional
instructions that is in the provided CD-ROM.
Cleaning and maintenance
Ask an Authorised Service Centre
to clean the inside of the projector
at least once a year.
If dust is left to build up inside the projector without
being cleaned out, it can result in re or problems
with operation. It is a good idea to clean the inside of
the projector before the season when humid weather
arrives.
Ask your nearest Authorised Service Centre to clean
the projector when required.
Please discuss with the Authorised Service Centre
regarding cleaning costs.
Be sure to remove the mains plug from the
z
mains socket before cleaning.
Use soft and dry cloth to clean the cabinet.
z
Use a soft cloth moistened in warm water to clean
away oil. Do not use solvents such as benzene,
thinner, and alcohol, detergents for kitchens, or a
chemical cloth. If using such solvents, the outer
case will become deformed, and the paint may peel
off.
Do not clean the lens surface with fuzzy or
z
dusty cloths.
If dust adheres to the lens, it will be magnied and
projected on the screen. Use a soft and clean cloth
to wipe off dust.
Disposal
When discarding this product, please contact your local
authorities or dealer and ask for the correct method of
disposal.
Precautions with regard to safety
10 - ENGLISH
Important
Information
Accessories
Make sure the following accessories are provided with your projector.
Remote control for
N2QAYB000450
Safety cable
TTRA0141
Attachment screw (x1)
Safety cable (x1)
Lens cover (x1)
TXFKK01REGZ
(Attached to the projector
by default.)
CD-ROM (x1)
TXFQB02REGZ
Mains lead for continental Europe (x1)
K2CM3FH00001
3 m (9'10 1/8")
Mains lead for UK (x1)
K2CT3FH00003
3 m (9'10 1/8")
R6 size batteries for remote control (x2)
TTRA0183
* The protectors for enclosed products, such as a plug
cover or foam cartons, must be treated properly.
* Contact an Authorised Service Centre for lost
accessories.
Power cord secure lock (x1)
ENGLISH - 11
Preparation
About Your Projector
Remote control
Power button
While MAIN POWER is on,
switch between standby
mode and projection mode.
Button backlight
When any button is pressed, the button
backlight is lit. Without any operation, it
gets darker after 5 seconds and goes
off after next 5 seconds.
Remote control signal emitter
Emit remote control signal.
Display the PICTURE menu
or ADVANCED MENU.
Switch to cycle through the
PICTURE MODE.
Display the VIERA LINK
MENU.
Display the main menu or
return to the previous menu.
Navigate through the
menus with ▼ ◄ ►,
and activate the menu
item with the ENTER
button.
Open the connected
equipment menu while using
the VIERA Link.
Switch to cycle through
the input method.
Display the ZOOM/FOCUS
menu.
Display the MEMORY LOAD
menu.
Capture the projected image
as a still image.
Display the input waveform.
Reset some of the settings
to the factory default.
Return to the previous menu.
Activate the assigned
function from the menu
options for shortcut.
Battery compartment
Press the tab and lift up the cover.1.
Insert the batteries according to the polarity diagram indicated 2.
inside.
Note:
See the functional instructions that is in the provided CD-ROM for more details. •
Do not drop the remote control. •
Avoid contact with liquids or moisture. •
Use manganese batteries or alkaline batteries with the remote control. •
Do not attempt to modify or disassemble the remote control. Contact an Authorised Service Centre for repairs. •
Do not keep pressing the remote control buttons as this may shorten battery life. •
Preparation
About Your Projector
12 - ENGLISH
Preparation
Projector body
Top and front view
J
Air exhaust port
Heated air comes out
of this opening.
Lens shift dials • Vertical Lens shift dials • Horizontal
Projection lens
Power/LAMP/TEMP
indicators
Air lter
MAIN POWER
Switch the projector on/off.
Lens cover
Protects the projection lens
from dust or dirt.
Remote control signal
receptor
Air exhaust port
(Push to open/close the cover.)
Navigate through the menus with ▲ ▼ ◄ ►,
and activate the menu item with the ENTER
button.
Power button
While MAIN POWER is on, switch between
standby mode and projection mode.
MENU
Display the main menu.
Return to the previous menu.
INPUT SELECT
Switch to cycle through the
input method.
RETURN
Return to the previous menu.
FOCUS and ZOOM
Adjust the focus and size of
the image.
CONTROL PANEL
Note:
While the projector is not in use, keep the lens cover attached to protect the lens. •
About Your Projector
ENGLISH - 13
Preparation
Back and bottom view
J
Air intake port Security lock
Attach the commercial shackle lock
which is provided with the projector.
Compatible with the Kensington
MicroSaver Security System.
Front leg adjusters
Screw up/down to adjust the
projection angle.
Lens cover attachment hole
Top cover
Hold the top cover at the back corner
and slightly push up to open.
Air intake port
AC IN
Connect the mains lead to
supply electronic power to the
projector.
Safety cable attachment point
Attach the safety cable when
mounted on the ceiling.
Front leg adjusters
Screw up/down to adjust the
projection angle.
HDMI IN
Connect HDMI signal cables.
COMPUTER IN
Connect an RGB/YP
B
P
R
signal
cable.
COMPONENT IN
Connect a YP
B
P
R
signal cable.
S-VIDEO IN
Connect an S-VIDEO
signal cable.
VIDEO IN
Connect an RCA
composite video cable.
Connecting
terminals
TRIGGER IN/OUT
Connect external equipment
controlling cables.
SERIAL
Connect a compatible
cable for controlling the
projector remotely via
your computer.
NOTE:
The projector should only be used with the attached mains lead to ensure optimum performance and avoid damage to •
the projector.
Do not open the top cover other than replacing the lamp unit. •
See the functional instructions that is in the provided CD-ROM for more details. •
14 - ENGLISH
Getting
Started
Setting up
Screen size and throw distance
You can adjust the projection size with 2 × zoom lens. Calculate and dene the throw distance as follows.
Projected image
SD
SW
SH
Screen Screen
All measurements and the calculation results below are approximate and may differ from the actual measurements.
Throw distance (16:9) Throw distance (2.35:1)
Screen Diagonal
(SD)
Minimum distance
(LW)
Maximum distance
(LT)
Minimum distance
(LW)*1
Maximum distance
(LT)
2.03 m (80") 2.4 m (7'10") 4.7 m (15'5") 2.6 m (8'6") 3.8 m (12'5")
2.54 m (100") 3.0 m (9'10") 5.9 m (19'4") 3.2 m (10'6") 4.7 m (15'5")
3.05 m (120") 3.6 m (11'9") 7.2 m (23'7") 3.8 m (12'5") 5.7 m (18'8")
When using both 2.35:1 and 16:9 aspect images onto a 2.35:1 sized screen.*1.
JCalculation methods for screen dimensions
You can calculate more detailed screen dimensions from the screen diagonal.
16:9 size 2.35:1 size
Screen height (SH) = SD (m) × 0.490 = SD (m) × 0.392
Screen width (SW) = SD (m) × 0.872 = SD (m) × 0.920
Minimum distance (LW) = SD (m) × 1.189 − 0.04 = SD (m) × 1.256 − 0.04
Maximum distance (LT) = SD (m) × 2.378 − 0.05 = SD (m) × 1.899 − 0.05
NOTE:
You can tilt the projector body less than approximately ±30 ° vertically and ±10 ° horizontally. •
Overtilting may result in shortening the component’s life.
Do not cover the air exhaust/intake ports or place anything within 50 cm (19 5/8") of them. •
+30 °
−30 °
Projection method
You can use the projector with any of the following 4 projection methods. To set the projector in the desired
method, see “INSTALLATION” in “OPTION menu” of the functional instructions that is in the provided CD-ROM.
Mounting on the ceiling and
J
projecting from front
Setting on a desk/oor and
J
projecting from rear
INSTALLATION: FRONT/CEILING INSTALLATION: REAR/DESK
Mounting on the ceiling and
J
projecting from rear
Setting on a desk/oor and
J
projecting from front
INSTALLATION: REAR/CEILING INSTALLATION: FRONT/DESK
NOTE:
A translucent screen is required for rear projection. •
When mounting the projector on the ceiling, the optional ceiling mount bracket (ET-PKE2000, ET-PKE1000S) is required. •
See “Ceiling mount bracket safeguards” on page •30.
Getting Started
Setting up
ENGLISH - 15
Getting
Started
Lens shift and positioning
If the projector is not positioned right in front of the centre of the screen, you can adjust the projected image
position by moving the lens shift dials within the shift range of the lens.
Adjusting the lens shift dials
J
Horizontal shift Vertical shift
Horizontal shift
Q
You can place the projector where the projector
lens is up to 40 % horizontally off-centre from the
screen and then adjust the image position with
the Lens shift dial • Horizontal.
Up to about 40 %
of the projection
Up to about 40 %
of the projection
Turning the dial
counterclockwise:
Image moves to the left
Turning the dial
clockwise:
Image moves to the right
Vertical shift
Q
You can place the projector where the projector
lens is up to 100 % vertically off-centre from the
screen and then adjust the image position with
the Lens shift dial • Vertical.
Up to about 100 %
of the projection
Up to about 100 %
of the projection
Turning the dial counterclockwise:
Image moves to the bottom
Turning the dial clockwise:
Image moves to the top
Connections
Before connecting to the projector
Read and follow the operating and connecting instructions of each peripheral device.
The peripheral devices must be turned off.
Use cables that match each peripheral device to be connected.
Conrm the type of video signals. See “List of compatible signals” on page
31.
Audio cables must be connected from each peripheral device directly to the audio reproduction system.
NOTE:
See the functional instructions that is in the provided CD-ROM. •
16 - ENGLISH
Basic
Operation
Switching the projector on/off
Basic Operation
Mains lead
Connecting
J
Make sure the shape of the mains plug and the 1.
AC IN terminal on the back of the projector match,
then push the plug all the way in.
Align the side of the 2. power cord secure lock with
the side guide rail of the AC IN terminal of the
projector and slide it in.
Rail guide
Place the latch to the latch catcher and press until 3.
it clicks.
Latch
Connect the mains plug to a mains socket.4.
Disconnecting
J
Unplug the mains plug from the mains socket.1.
Depress the latch and slide the cover off.2.
Slide the power cord secure lock up along the side 3.
guide rail.
Hold the plug and unplug it from the 4. AC IN
terminal on the back of the projector.
NOTE:
Do not use other than the provided mains lead. •
Ensure all the input devices are connected and turned off before connecting the mains lead. •
Do not force the connector as this may damage the projector and/or the mains lead. •
Dirt or dust build-up around plugs may cause re or electrical hazards. •
Switch off the power to the projector when not in use. •
Power indicator
Power indicator informs you of the status of the power.
When the
TEMP indicator is ashing, the power
indicator will turn red, and you cannot switch on the
power.
Power indicator
Indicator status Status
No illumination or ashing MAIN POWER is switched off.
Red
Lit MAIN POWER is switched on and the projector is in standby mode.
Flashing
MAIN POWER is switched on (standby mode) and the POWER ON LINK is set to
ON.
The power consumption is not much different when it is lit.
•
( See “VIERA Link Connection” of the functional instructions that is in the provided
CD-ROM.)
Green
Flashing The power button is switched on and the projector is getting ready to project.
Lit Projecting.
Orange
Lit The power button is switched off and the projector is cooling the lamp.
Flashing The power button is switched on again when cooling the lamp and recovering to
projection mode. Recovery may take a while.
NOTE:
See “TEMP indicator” on page •25.
While the projector is cooling the lamp, do not switch •MAIN POWER off or unplug the mains lead.
The electric consumption in standby mode is 0.08 W. •
Switching the projector on/off
ENGLISH - 17
Basic
Operation
Switching on the projector
(2)
(3)
(1)
Power indicator
Remove the lens cover from the lens.1.
Switch 2. MAIN POWER on.
The power indicator lights up in red.
Press the power button.3.
The power indicator lights up in green after ashing
for a while.
The
STARTUP LOGO is displayed on the screen.
See “STARTUP LOGO” in “OPTION menu” of
the functional instructions that is in the provided
CD-ROM.
NOTE:
When the internal cooling fan is operating, some operational sound may be heard. The loudness of the operational •
sound depends on the external temperature.
You can reduce the operational sound by setting the •LAMP POWER in OPTION menu to the ECO-MODE. See “LAMP
POWER” in “Option menu” of the functional instructions that is in the provided CD-ROM.
When starting up the projector, some small rattling or tinkling sound may be heard, or the display may icker for the •
characteristics of the lamp. Those are normal and will not affect the performance of the projector.
Do not attempt to modify the lens cover which may cause burns, re or damage to the projector. •
Switching off the projector
(3)
(1)
(2)
Power indicator
Press the power button.1.
The conrmation screen is displayed.
To return to the projection, press the
MENU or
RETURN button.
Press the power or 2. ENTER button.
The power indicator lights up in orange while cooling
the lamp, then illuminates red when it is ready to
switch off MAIN POWER.
Switch off 3. MAIN POWER on the left side of the
projector.
Attach the lens cover.4.
NOTE:
Press the power button twice or for a long duration to switch the power off. •
18 - ENGLISH
Basic
Operation
Projecting an image
Selecting the input signal
Switch on the connected devices.1.
Press the play button of the required device.
Press the 2. INPUT SELECT button to select the
required input method if needed. See “Switching
the input signal” of the functional instructions that
is in the provided CD-ROM.
The image will be projected on the screen.
NOTE:
AUTO SEARCH • is ON as default and the signal from
the connected devices is detected automatically.
See “AUTO SEARCH” in “OPTION menu” of the
functional instructions that is in the provided CD-ROM.
Positioning the image
Adjust the projected image with the lens shift dials. 1.
See “Lens shift and positioning” on page 15.
Adjust the angle of the projector.2.
You can screw the front leg adjusters up/down to
control the angle of the projector for adjusting the
throwing angle.
Screw up the front leg adjusters, and an audible click
will be heard as the limit.
Adjust the focus and the projected image size.3.
Press +/− of the
FOCUS and ZOOM buttons to
adjust.
Press the
LENS button to adjust the focus and zoom
by the remote control. See “LENS CONTROL” of
the functional instructions that is in the provided CD-
ROM.
NOTE:
Do not touch the air exhaust port as this may cause •
burns or injury.
If keystone distortion occurs, see “KEYSTONE” in •
“POSITION menu” of the functional instructions that is
in the provided CD-ROM.
If you adjust the focus, you may need to adjust the size •
of the image by pressing the ZOOM button again.
ENGLISH - 19
Settings
Menu Navigation
Settings
Navigating through the MENU
JDisplaying the main menu
Press the MENU button to display the main
menu and the operating guidance.
-
+
-
+
-
+
-
+
-
+
-
+
PICTURE MODE
CONTRAST
BRIGHTNESS
COLOUR
TINT
SHARPNESS
COLOUR TEMPERATURE
DYNAMIC IRIS
WAVEFORM MONITOR
SPLIT ADJUST
ADVANCED MENU
MEMORY SAVE
MEMORY LOAD
MEMORY EDIT
NORMAL
ON
0
0
0
0
0
0
PICTURE
POSITION
LANGUAGE
LENS CONTROL
FUNCTION BUTTON
VIERA LINK MENU
OPTION
ENTER
RETURN
SELECT
Main menu
Operating guidance
Contains the required buttons to adjust the settings.
Sub-menu
Current
settings
Adjusting with the bar scale
J
items
The triangle mark under the bar indicates factory
default setting and the square indicates the current
setting.
-
+
BRIGHTNESS 0
Current setting
Default
JReturning to the previous menu
Press the MENU or RETURN button to return
to the previous menu. Press repeatedly to
escape from the menu mode and return to the
projection.
JResetting to the factory default
settings
You can reset most of the customised settings
to the factory defaults by pressing DEFAULT
button of the remote control.
Operating procedure
J
Press ▲ ▼ to scroll to the required main menu 1.
item and press the ENTER button to select.
The selected item is highlighted in orange and the
sub-menu is displayed on the right.
See “Menu list” on page
20.
-
+
-
+
-
+
-
+
H-POSITION
V-POSITION
ASPECT
WSS
OVER SCAN
KEYSTONE
16:9
ON
0
0
+7
0
PICTURE
POSITION
LANGUAGE
LENS CONTROL
FUNCTION BUTTON
VIERA LINK MENU
OPTION
ENTER
RETURN
SELECT
Press ▲ ▼ to scroll to the required sub-menu item 2.
and press ◄ ► or the ENTER button to adjust.
The selected item is called up and the other menu
items disappear from the screen. The Called up item
will disappear after 5 seconds without any operation
and return to the menu mode.
If there is a lower level to the sub-menu item, the
next level will be displayed.
-
+
-
+
-
+
-
+
H-POSITION
V-POSITION
ASPECT
WSS
OVER SCAN
KEYSTONE
16:9
ON
0
0
+7
0
PICTURE
POSITION
LANGUAGE
LENS CONTROL
FUNCTION BUTTON
VIERA LINK MENU
OPTION
ENTER DEFAULT
RETURN
SELECT
Press ◄ ► to adjust or set the selected item.3.
For items using a bar scale, the current settings are
displayed on the left of the bar scale.
You can cycle through the options of an item by
pressing ▲ ▼.
-
+
BRIGHTNESS 0
Press the 4. MENU or RETURN button to return to
the previous menu.
Menu Navigation
20 - ENGLISH
Settings
Menu list
The menu options are structured and categorised. You can navigate through the menu with ▲ ▼ ◄ ► buttons.
NOTE:
The underlined items are factory default settings. •
Some default settings vary by the selected input signal. •
Sub-menu items vary according to the selected input signal. •
Some settings are adjustable without any signals. •
PICTURE
It is possible to adjust the picture quality.
PICTURE MODE
NORMAL DYNAMIC
COLOUR1 COLOUR2
CINEMA1 CINEMA2
CINEMA3
CONTRAST
(Default: 0)
BRIGHTNESS
(Default: 0)
COLOUR
(Default: 0)
TINT
(Default: 0)
SHARPNESS
(Default: 0)
COLOUR TEMPERATURE
(Default: 0)
DYNAMIC IRIS
ON OFF
WAVEFORM MONITOR
OFF
FULL SCAN(Y) FULL SCAN(R)
FULL SCAN(G) FULL SCAN(B)
SINGLE LINE SCAN(Y)
SINGLE LINE SCAN(R)
SINGLE LINE SCAN(G)
SINGLE LINE SCAN(B)
MONITOR POSITION
UPPER LEFT UPPER CENTRE
UPPER RIGHT LOWER LEFT
LOWER CENTRE LOWER RIGHT
AUTO ADJUST
START AUTO ADJUST
BLACK LEVEL ADJUST
WHITE LEVEL ADJUST
RGB ADJUST (BLACK)
RGB ADJUST (WHITE)
SPLIT ADJUST
AREA SELECT
SPLIT ADJUST MODE
NORMAL REVERSE
▼
▲
ADVANCED MENU
GAMMA ADJUSTMENT
SIMPLE ADVANCED
CONTRAST R (Default: 0)
CONTRAST G (Default: 0)
CONTRAST B (Default: 0)
BRIGHTNESS R (Default: 0)
BRIGHTNESS G (Default: 0)
BRIGHTNESS B (Default: 0)
NR (Default: 0)
MPEG NR (Default: 0)
FRAME CREATION
OFF MODE1
MODE2 MODE3
COLOUR MANAGEMENT
PROFILE ADJUSTMENT MODE
START ADJUSTMENT LOG
PROFILE SAVE PROFILE DELETE
PROFILE NAME CHANGE
x.v.Colour
ON OFF
DETAIL CLARITY (Default: 3)
CINEMA REALITY
ON OFF
TV-SYSTEM
AUTO
NTSC NTSC 4.43
PAL PAL-M
PAL-N SECAM
RGB/YPbPr
AUTO RGB YPbPr
MEMORY SAVE
MEMORY 1 - 16
MEMORY LOAD
MEMORY 1 - 16
MEMORY EDIT
MEMORY DELETE
MEMORY 1 - 16 ALL DELETE
MEMORY NAME CHANGE
MEMORY 1 - 16
SIGNAL MODE
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Panasonic PT-AE4000E Owner's manual
- Category
- Data projectors
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Panasonic PT-CMZ50WU User manual
-
Panasonic Panasonic Europe PT-DZ10KE User manual
-
Panasonic PT-EZ770 Series User manual
-
Panasonic PT-DZ6700E User manual
-
Panasonic PT-AX200E Operating Instructions Manual
-
-
Technicolor - Thomson PT-AE2000E User manual
-
Panasonic PT-AE3000E User manual
-
Panasonic PTAX100E User manual
-
