Symmons 532HSB-STN Installation guide
- Category
- Wall & ceiling mounts accessories
- Type
- Installation guide
Museo®
Model Numbers Specification
Modifications
Hand shower unit includes dual checks for backow
protection, 30" slide bar with cradle for hand shower
mounting, 60" exible metal hose, 2 mode hand shower
and standard 2.5 gpm (9.5 L/min) ow restrictor.
Components made from metal and nonmetallic materials,
plated in standard polished chrome nish.
Note: Append appropriate -sufx to model number.
Compliance
-ASME A112.18.1/CSA B125.1
Warranty
Limited Lifetime - to the original end purchaser in
consumer/residential installations.
5 Years - for industrial/commercial installations.
Refer to www.symmons.com/warranty for complete
warranty information.
532HSB
Hand Shower Unit
Operation & Maintenance Manual
-1.5 1.5 gpm (5.7 L/min) flow restrictor
-2.0 2.0 gpm (7.6 L/min) flow restrictor
-STN Satin Nickel finish
CG
Measurements
A 3-1/8", 79 mm
B
Male 1/2-14 NPT tting must
be recessed 1/4" (6 mm)
from nished wall
C
(2x) Hole Size
Dry wall: Ø 3/16", 5 mm
Stud: Ø 1/8", 3 mm
D 28-5/16", 719 mm
DD
AA
BB
C C
Note: Dimensions subject to change without notice.
Dimensions
532HSB
Hand Shower Unit
2
Parts Breakdown
Replacement Parts
Item Description Part Number
A Hand Shower 402W*
B
C
D
Slide Bar EF-02284*
E Wall Elbow EF-105*
FVacuum Breaker
(optional) EF-109*
G 60" Hose EF-02976
Note: Append modication -STN to part number
for Satin Nickel nish.
A
B
C
D
E
F
G
Tools Required for Installation
Adjustable
Wrench
Allen Wrench:
3 mm
Phillips Head
Screwdriver
Plumber Tape
Power Drill
Silicone
Notes:
1) Apply a bead of silicone around the perimeter of all shower trim
installed ush to the nished wall (less mounting plates and
brackets). Leave opening on bottom of escutcheons for weep hole.
2) Apply plumber tape to all threaded connections.
3
Installation
1a)
Dry Wall Option: R
emove upper
and lower caps (B) from slide bar
brackets. Place slide bar (D) into
desired position. Using brackets
as a guide, carefully drill 3/16"
holes into wall. Remove slide bar
and install anchors.
Notes: Make sure that slide bar holes
and bracket holes are aligned before
drilling. Before drilling bottom hole,
make sure slide bar is plumb.
1b) Stud Option: R
emove upper and
lower caps (B) from slide bar
brackets. Place slide bar (D) into
desired position. Using brackets
as a guide, carefully drill 1/8"
pilot holes into stud.
Notes: Make sure that slide bar holes
and bracket holes are aligned before
drilling. Before drilling bottom hole,
make sure slide bar is plumb.
2) With slide bar (D) in position,
secure to wall using screws (C).
Replace upper and lower caps (B)
onto slide bar brackets.
4
4
1
1
2
2
3
B
D
B
1
1
2
2
3
B
D
B
2
2
1
C
D
B
B
D
Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184 ■ Phone: (800) 796-6667 ■ Fax: (800) 961-9621
Copyright © 2019 Symmons Industries, Inc. ■ symmons.com ■ [email protected] ■ ZV-3223 REV C ■ 022219
Installation
3) Install wall elbow (E) to stub
out pipe. Tighten set screw
to secure.
1
2
E
E
3
1
4
2
A
G
G
4) Attach large end of hose (G)
to hand shower wand (A).
Attach small end of hose (G) to
wall elbow (E). Turn clockwise to
tighten.
Troubleshooting Chart
Finish is spotting. Elements in water supply may cause
water staining on nish.
Clean nished trim area with a soft
cloth using mild soap and water or a
non-abrasive cleaner and then quickly
rinse with water.
Troubleshooting Chart
WARNING: This product can expose you to chemicals including lead, which is known to the state of California to
cause cancer, birth defects, or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
-
1
-
2
-
3
-
4
Symmons 532HSB-STN Installation guide
- Category
- Wall & ceiling mounts accessories
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Symmons S-3604-BBZ-T4-1.5-TRM Installation guide
-
-
-
-
-
-
-
-
Symmons S-4404-2.0-TRM Installation guide
-