Electrolux EFG750X/A User manual

Brand: Electrolux

Model: EFG750X/A

Category: Cooker hoods

Type: User manual

Electrolux EFG750X/A is a kitchen range hood designed to eliminate cooking smells and improve indoor air quality. It operates in two modes: ducted and recirculation. In ducted mode, the hood exhausts air to the outside through a duct, while in recirculation mode, it filters and recirculates the air back into the kitchen. The hood has three speed settings, allowing you to adjust the airflow to suit your cooking needs. It also features a built-in lighting system to illuminate your cooking area.

USER MANUAL

EFG750X/A

We were thinking of you

when we made this product

electrolux 3

RECOMMENDATIONS AND SUGGESTIONS 4

CHARACTERISTICS 5

INSTALLATION 6

USE 8

MAINTENANCE 9

Welcome to the world of Electrolux

Thank you for choosing a rst class

product from Electrolux, which hopeful-

ly will provide you with lots of pleasure

in the future. The Electrolux ambition is

to offer a wide variety of quality prod-

ucts that make your life more comfort-

able. You nd some examples on the

cover in this manual. Please take a few

minutes to study this manual so that

you can take advantage of the benets

of your new machine. We promise that

it will provide a superior User Experi-

ence delivering Ease-of-Mind.

Good luck!

This appliance is intended to be used in household and similar applications such as:

- Staff kitchen areas in shops, ofces and other working environments

- Farm Houses

- By clients in hotels, motels and other residential type environments

- Bed and breakfast type environments.

4 electrolux Recommendations and Suggestions

Installation

• The manufacturer will not be held liable for

any damages resulting from in-correct or

improper installation.

• The minimum safety distance between

the cooker top and the extractor hood is

650 mm (some models can be installed at

a lower height, please re-fer to the para-

graphs on working dimensions and instal-

lation).

• Check that the mains voltage corresponds

to that indicated on the rating plate xed

to the inside of the hood.

• For Class I appliances, check that the

domestic power supply guarantees ad-

equate earthing.

• Connect the extractor to the exhaust ue

through a pipe of minimum diame-ter 120

mm. The route of the ue must be as short

as possible.

• Do not connect the extractor hood to ex-

haust ducts carrying combustion fumes

(boilers, replaces, etc.).

• If the extractor is used in conjunction with

non-electrical appliances (e.g. gas burning

appliances), a sufcient degree of aeration

must be guaranteed in the room in order

to prevent the backow of exhaust gas.

The kitchen must have an opening com-

municating directly with the open air in or-

der to guar-antee the entry of clean air.

Use

• The extractor hood has been designed

exclusively for domestic use to elimi-nate

kitchen smells.

• Never use the hood for purposes other

than for which it has been designed.

• Never leave high naked ames under the

hood when it is in operation.

• Adjust the ame intensity to direct it onto

the bottom of the pan only, making sure

that it does not engulf the sides.

• Deep fat fryers must be continuously

monitored during use: overheated oil can

burst into ames.

• Do not ambè under the range hood; risk

of re

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless

they have been given supervision or in-

struction concern-ing use of the appliance

by a person responsible for their safety.

• Children should be supervised to ensure

that they do not play with the appli-ance.

Maintenance

• Switch off or unplug the appliance from

the mains supply before carrying out any

maintenance work.

• Clean and/or replace the Filters after the

specied time period (Fire hazard).

• Clean the hood using a damp cloth and a

neutral liquid detergent.

The symbol

on the product or on

its packaging indicates that this product

may not be treated as household waste.

Instead it should be taken to the appropriate

collection point for the recycling of electrical

and electronic equipment. By ensuring this

product is disposed of correctly, you will help

prevent potential negative consequences for

the environment and human health, which

could otherwise be caused by inappropriate

waste handling of this product. For more

detailed information about recycling of this

product, please contact your local council,

your household waste disposal service or

the shop where you purchased the product.

RECOMMENDATIONS AND SUGGESTIONS

Characteristics electrolux 5

Dimensions

CHARACTERISTICS

Components

Ref. Q.ty Product Components

1 1 Hood Body, with: Controls, Light,

Blower, Filters

9 1 Reducer Flange ø 150-120 mm

Ref. Q.ty Installation Components

12f 8 Screws 3,5 x 16

Q.ty Documentation

1 Instruction Manual



















Hood Type 52 70

L1 522 702

6 electrolux Installation

INSTALLATION

Drilling the Support surface and

Fitting the Hood

• Make a rectangular opening on the

base of the hanging unit, leaving a mi-

nimum of 13 mm from the outer ed-

ges.

Hood Type 52 70

L1 497 677

SNAP-ON FITTING

For hoods with snap-on side supports

only, set up for a support panel

thickness of between 15 mm and 30

mm.

• Insert the hood until the side supports

snap into place.

• Lock in position by tightening the

screws Vf from underneath the hood.

SCREW FITTING

For hoods without snap-on side sup-

ports only.

• Fix the hood to the hanging unit using

the screws 12f (3.5x16 self-threading)

provided.









Installation electrolux 7

Connections

DUCTED VERSION AIR EXHAUST

SYSTEM

When installing the ducted version, con-

nect the hood to the chimney using ei-

ther a exible or rigid pipe ø 120 or 150

mm, the choice of which is left to the

installer.

• To install a ø 120 mm air exhaust con-

nection insert the reducer ange 9 on

the hood body outlet.

• Fix the pipe in position using sufcient

pipe clamps (not supplied).

• Remove any activated charcoal l-

ters.

RECIRCULATION VERSION AIR OUT-

LET

• Cut a hole ø 120 mm in any shelf that

may be positioned over the hood.

• Insert the reducer ange 9 on the

hood body outlet.

• Connect the hood body outlet to the

top part of the wall unit using a rigid or

exible pipe ø 120 mm, to be selected

by the installer.

• Fix the pipe in position using sufcient

pipe clamps (not supplied).

• Ensure that the activated charcoal

lters have been inserted.

ELECTRICAL CONNECTION

• Connect the hood to the mains

through a two-pole switch having a

contact gap of at least 3 mm.

















8 electrolux Use

USE

L Light Switches the lighting system on and off.

M Motor Switches the extractor motor on and off.

V Speed Sets the operating speed of the extractor:

1.Low speed, used for a continuous and silent air change in the

presence of light cooking vapour.

2.Medium speed, suitable for most operating conditions given

the optimum treated air ow/noise level ratio.

3.Maximum speed, used for eliminating the highest cooking va

pour emission, including long periods.

Maintenance electrolux 9

Grease lters

CLEANING METAL CASSETTE GREASE

FILTERS

• The lters must be cleaned every 2

months, or more frequently in case of

particularly heavy use of the hood. Filters

can be washed in a dishwasher.

• Remove the lters one at a time, after

disconnecting the relative fastening ele-

ments.

• Wash the lters, taking care not to bend

them. Allow them to dry before retting.

• When retting the lters, make sure that

the handle is visible on the outside.

Charcoal lter (Recycling version)

REPLACING CHARCOAL FILTERS

Warning: Turn the lights off and wait until

the lamps cool down before you change

the odour lter.

• Remove the grease lters.

• Remove the saturated activated carbon

lters by releasing the xing hooks.

• Fit the new lters by hooking them into

their seating

• Replace the grease lters.

Lighting

LIGHT REPLACEMENT

40 W incandescent light.

• Remove the metal grease lters. Discon-

nect the cooker hood from the mains

supply.

• Unscrew the bulbs and replace them

with new ones having the same charac-

teristics.

• Replace the metal grease lters.

MAINTENANCE

10 electrolux Maintenance

www.electrolux.com

436003033_02 - 110826

Electrolux EFG750X/A User manual

Brand: Electrolux

Model: EFG750X/A

Category: Cooker hoods

Type: User manual

Download PDF

report

Electrolux EFG750X/A User manual

Electrolux EFG750X/A User manual

Related papers

Other documents