THIS INSTRUCTION BOOK MAY CONTAIN ERRORS AND OMISSIONS.
DESIGN AND SPECIFICATION ARE SUBJECT TO CHANGE WITHOUT NOTICE.
ESTE MANUAL DE INSTRUCCIONES PUEDE CONTENER ERRORES Y OMISIONES.
EL DISEÑO Y LAS ESPECIFICACIONES ESTÁN SUJETOS A CAMBIO SIN PREVIO AVISO.
CE LIVRET D’INSTRUCTIONS PEUT CONTENIR DES ERREURS ET DES OMISSIONS
LE DESIGN ET LES CARACTÉRISTIQUES SONT SUJETS AUX CHANGEMENT SANS PRÉAVIS
F300ACRE Eng 15/5/07, 16:086
GB - 1
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALI-
FIED SERVICE PERSONNEL.
The lighting flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to
the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
The symbol for Class II (Double Insulation)
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
The apparatus should not be exposed to dripping or splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
The ventilation should not be impeded by covering the ventilation openings with items, such as
newspapers, table-cloths, curtains, etc.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
The mains plug is used as the disconnect device, the disconnect device should remain readily operable.
In order to disconnect he apparatus from the mains completely, the mains plug should be disconnected
from the mains socket outlet completely.
FOR UK ONLY
For your own safety read following instructions carefully before attempting to connect this alarm
radio clock to the mains.
Mains Supply 220V - 240V~ 50Hz - AC only
This unit is designed to operate on a 220V-240V~ 50Hz supply only. Connecting it to other power
sources may damage it. Ensure that the supply corresponds to the information on the rating label on
the rear panel of the unit.
This component system may be fitted with a non-rewireable plug. If it is necessary to change the
fuse in a non-rewireable plug the fuse over must be refitted. If the fuse cover becomes lost or
damaged, the plug must not be used until a replacement, available from the manufacturer, is
obtained. It is important that the colour of the replacement fuse cover corresponds with the colour
marking on the base of the plug.
If the plug needs to be changed because it is not suitable for your socket, or becomes damaged, it
should be cut off and an appropriate plug fitted following the wiring instructions below. The plug
must then be disposed of safely, as insertion into a 13A socket is likely to cause an electrical hazard.
IMPORTANT
The wires in the mains plug should be connected as shown in the diagram.
The colours of the wires in the mains lead of the unit may not correspond with the coloured markings
identifying the terminals in your plug. Connect them as follows:-
The wire which is coloured blue must be connected to the
terminal which is marked with the letter ‘N’ or coloured
black.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter ‘L’ or coloured red.
There should be no connectin to the earth terminal of your
plug.
If a 13 Amp (BS1363) Plug is used, a 3 Amp Fuse must be
fitted, or if any other type of Plug is used a 3 Amp or 5 Amp
Fuse must be fitted, either in the Plug or Adaptor, or on the
Distribution Board.
CORD GRIP
FUSE
BROWN
or RED
(LIVE)
L
OUTER
SLEEVE
BLUE
or BLACK
(NEUTRAL)
N
F300ACRE Eng 18/4/07, 14:491
GB - 2
LOCATION OF CONTROLS
1. “AUTO” Indicator
2. LED display
3. “HOUR” button
4. “SNOOZE” button
5. “MINUTE” button
6. “TIMER (Time Set)” button
7. “ALARM SET” button
8. Speaker
9. Radio Tuning knob
10. Light ON/OFF button
(for “dew drops’ lights on mushroom)
11. Radio Band switch “AM/FM”
12. Battery compartment
(bottom of alarm clock)
13. Function switch,
“OFF/ON/BUZZER/AUTO”
14. Volume knob
15. AC mains cord
16. FM antenna
8
1
3
257
46
12
15
16
10
9
11
13
14
F300ACRE Eng 18/4/07, 14:492
GB - 3
MAIN POWER SUPPLY
- Check that the power voltage as shown on the type plate corresponds to your local
power voltage. If it does not, consult your dealer or service organization.
- Connect the power cord to the wall outlet of AC power supply. As soon as you insert
the power plug into the wall outlet, the display time will flash and show . (Assuming
there is no battery for backup or battery is weak). Please see below how to set the
correct time.
POWER FAILURE
If power failure occurs, the unit will switch off. As soon as the power supply returns,
will flash and display, indicating that you must reset the correct time.
BATTERY BACK-UP SYSTEM
1. Open the battery compartment cover by removing the
screw, then slide the battery cover out.
2. Insert 1 x “006P” or “6F22” sized (9V) battery (not
included) into the battery compartment. In the event of a
power failure, the battery will provide sufficient power to
maintain the time. When AC power is restored, the
correct time will be restored and will not require
resetting.
•
Neither the display nor the unit will operate until the unit is connected to an AC outlet. BATTERY
WILL ONLY RESTORE CLOCK SETTINGS WHEN AC POWER IS RESTORED.
• Replace the battery once per year. The service of the battery depends on how often
and for how long the power supply fails. This varies from one region to another.
Note:
1. Always check the time and reset if necessary when first time connecting AC mains or
after a power failure.
2.
The battery is used for backing up the time in case of AC mains power failure, under this
circumstance, do not attempt to operate the unit, otherwise, battery service life will be reduced.
BATTERY PRECAUTIONS
Follow these precautions when using battery in this device:
1.
Do not attempt to recharge, short-circuit, disassemble, heat or throw the battery into a fire.
2. If the device is not to be used for a long period of time, remove the batteries to
prevent damage or injury from possible battery leakage.
3. Do not try to recharge battery, it is not intended to be recharged; they can overheat
and rupture. (Follow battery maufacturer’s directions.)
4. Dispose of battery properly in accordance with local laws.
POWER SOURCE
F300ACRE Eng 18/4/07, 14:493
GB - 4
OPERATION
AM/FM Radio Normal Operation
- Set the Function switch to “ON” to turn on AM/FM Radio, corresponding to the setting of
Radio Band switch to “AM/FM”.
- When Radio is turned on, turn the “Radio Tuning knob” to select desired radio stations.
- Turn the Volume knob to increase or decrease the sound level.
- To improve the radio reception, it is recommended to extend the FM wire antenna and
change its location for best reception. For AM band, move the unit to locate best reception
position.
- Set the Function switch to “OFF” position to turn off the Radio completely.
Setting Current Time
- Press and hold the “TIME” button, at the same time press the “HOUR” or “MINUTE”
button to adjust the current time.
Setting Alarm Time
- Press and hold the “Alarm Set” button, at the same time press the “HOUR” or “MINUTE”
button to adjust the desired alarm time.
Selection of Alarm mode
There are 2 alarm mode selections, “BUZZER” and “AUTO” (radio).
- Set the Function switch to either “BUZZER” or “AUTO”, LED indicator “AUTO” will light
up.
- When setting to “Auto”, also select “AM” or “FM” by sliding the Radio Band switch to
“AM/FM”.
- When current time coincides with desired alarm time, depending on the switch setting,
“Beep” or “Radio” will be activated for about 1 hour 59 minutes.
Snooze and Alarm Off
While Alarm is activating:
- Simply press the “SNOOZE” button to stop the alarm temporarily, after 9 minutes, it
repeats the alarm automatically, this can be repeated several times within the total
alarm duration.
- Simply press the “ALARM SET” button, alarm will be stopped and will be repeated
automatically in the next 24 hours at the same alarm time setting.
- Set the Function switch to “OFF” position to stop the alarm completely.
“Dew drops” light on mushroom
- Simply press Light “ON/OFF” button to turn ON or OFF the light.
Lights on Tinkerbell’s wings
- Once AC Mains power is connected, lights on Tinkerbell’s wings will be on.
F300ACRE Eng 18/4/07, 14:494
GB - 5
TROUBLESHOOTING GUIDE
Check the following guide for the possible cause of a problem before contacting service.
Symptom
Unit will not turn on
No sound from
speaker
No Radio
Alarm (Wake up)
no function
Cause
AC cord not connected
Function switch is not set
correctly
Volume control is set to
minimum
Function switch is not set
correctly
Radio Band switch not set
Alarm Time is not set.
Function switch is not set
correctly
Solution
Check AC cord connection
Set the Function switch to “On”
Turn to Volume control to
increase sound level
Set the Function switch to “On”
Set this switch to AM or FM
Set the Alarm Time correctly
Set the Function switch to
“Buzzer” or “Auto”
SPECIFICATIONS
Power source AC 220V - 240V ~ 50Hz
Clock backup system 9V Battery, 1 x “006P” or “6F22” (not included)
Power output 300mW
Power consumption 6W
Frequency range AM 530 - 1600 KHz
FM 88 - 108MHz
Clock display LED Display
* Design and specification are subject to change without notice.
F300ACRE Eng 18/4/07, 14:495
-
1
-
2
-
3
-
4
-
5
-
6
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Roberts Radio CR9919 User manual
-
Constant ELIPTICAL LED ALARM CLOCK User manual
-
Constant ELIPTICAL LED ALARM CLOCK User manual
-
Sytech SY1028R Owner's manual
-
-
-
TEAC CRX-195 Owner's manual
-
Sanyo RM-5750 User manual
-
-
