Toro Replacement Exhaust Pipe Kit, Dingo Model 22300 Compact Utility Loader Installation guide

Toro
Brand
Toro
Model
Replacement Exhaust Pipe Kit, Dingo Model 22300 Compact Utility Loader
Type
Installation guide

Toro Replacement Exhaust Pipe Kit, Dingo Model 22300 Compact Utility Loader is a must-have tool for anyone who owns a Dingo Model 22300 Compact Utility Loader. This kit includes everything you need to replace your existing exhaust pipe, including the upper and lower exhaust pipes, pipe clamps, a bracket, a bracket extension, a carriage bolt, a small lock washer, a large lock washer, a nut, a bolt, and a washer. With this kit, you can easily replace your old exhaust pipe and get your loader running like new again.

Here are some of the benefits of using the Toro Replacement Exhaust Pipe Kit:

  • Easy to install: The kit comes with all the necessary parts and instructions, so you can install it yourself in just a few minutes.

Toro Replacement Exhaust Pipe Kit, Dingo Model 22300 Compact Utility Loader is a must-have tool for anyone who owns a Dingo Model 22300 Compact Utility Loader. This kit includes everything you need to replace your existing exhaust pipe, including the upper and lower exhaust pipes, pipe clamps, a bracket, a bracket extension, a carriage bolt, a small lock washer, a large lock washer, a nut, a bolt, and a washer. With this kit, you can easily replace your old exhaust pipe and get your loader running like new again.

Here are some of the benefits of using the Toro Replacement Exhaust Pipe Kit:

  • Easy to install: The kit comes with all the necessary parts and instructions, so you can install it yourself in just a few minutes.
1
2003 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
Contact us at www.Toro.com
All Rights Reserved
Printed in the USA
Replacement Exhaust Pipe Kit
for Dingo
222 Compact Utility Loader (Model 22300)
Part No. 105-8400
Form No. 3329-935
Installation Instructions
Loose Parts
Description Qty. Use
Exhaust pipe, upper
Exhaust pipe, lower
Pipe clamps
Bracket
Bracket extension
Carriage bolt
Small lock washer
Large lock washer
Nut
Bolt
Washer
1
1
2
1
1
1
1
1
1
1
1
Install the exhaust pipe
Removing the Existing Exhaust
Pipe
1. Raise the loader arms and install the cylinder locks, stop
the engine, remove the key and allow the engine to cool
completely.
If the engine has been running, the muffler will be
very hot and can seriously burn you if you touch it.
Allow the engine and muffler to cool completely
before completing this procedure.
Warning
2. Remove and discard the bolt and washers securing the
existing exhaust pipe to the front of the engine.
3. Loosen the clamp securing the exhaust pipe to the
muffler.
4. Remove and discard the exhaust pipe and clamp.
Installing the Exhaust Pipe
1. If the clamps are not already on the exhaust pipes,
install them loosely over the pipes as shown in Figure 1.
2. Remove the upper nut from the clamp on the lower pipe
(Fig. 1).
1
3
4
6
m–6887
2
5
7
12
11
10
8
9
Figure 1
1. Upper exhaust pipe
2. Lower exhaust pipe
3. Pipe clamps
4. Install the bracket here.
5. Bracket
6. Bracket extension
7. Carriage bolt
8. Small lock washer
9. Nut
10. Bolt
11. Large lock washer
12. Washer
3. Install the bracket over the end of the clamp U-bolt and
secure it with the nut removed previously (Fig. 1).
4. Loosely install the bracket extension to the bracket
using a carriage bolt, small lock washer, and nut
(Fig. 1).
2
5. Loosely install the upper pipe into the lower pipe
(Fig. 1).
6. Loosely install the upper pipe onto the muffler.
7. Loosely secure the bracket extension to the threaded
hole in the front of the engine using a bolt, large lock
washer, and washer (Fig. 1).
8. Ensure that the exhaust pipe end is positioned in the
opening in the side of the frame.
9. Tighten the nuts on the 2 pipe clamps and other
fasteners to secure the pipe and brackets into place
(Fig. 1).
  • Page 1 1
  • Page 2 2

Toro Replacement Exhaust Pipe Kit, Dingo Model 22300 Compact Utility Loader Installation guide

Toro
Brand
Toro
Model
Replacement Exhaust Pipe Kit, Dingo Model 22300 Compact Utility Loader
Type
Installation guide

Toro Replacement Exhaust Pipe Kit, Dingo Model 22300 Compact Utility Loader is a must-have tool for anyone who owns a Dingo Model 22300 Compact Utility Loader. This kit includes everything you need to replace your existing exhaust pipe, including the upper and lower exhaust pipes, pipe clamps, a bracket, a bracket extension, a carriage bolt, a small lock washer, a large lock washer, a nut, a bolt, and a washer. With this kit, you can easily replace your old exhaust pipe and get your loader running like new again.

Here are some of the benefits of using the Toro Replacement Exhaust Pipe Kit:

  • Easy to install: The kit comes with all the necessary parts and instructions, so you can install it yourself in just a few minutes.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents