VONN Lighting VOB14638BL Installation guide

Brand
VONN Lighting
Model
VOB14638BL
Type
Installation guide

VONN Lighting VOB14638BL is a 12V AC Low Voltage LED bollard fixture, which can be used for outdoor lighting applications. It features a sturdy construction with a concrete base plate and a metal fixture, ensuring durability and weather resistance. The fixture emits a warm white light, creating a welcoming and inviting ambiance. The installation process is straightforward and requires basic electrical knowledge, making it suitable for DIY enthusiasts. The fixture comes with all the necessary hardware for installation, including expansion bolts, hex screws, and wire connectors.

VONN Lighting VOB14638BL is a 12V AC Low Voltage LED bollard fixture, which can be used for outdoor lighting applications. It features a sturdy construction with a concrete base plate and a metal fixture, ensuring durability and weather resistance. The fixture emits a warm white light, creating a welcoming and inviting ambiance. The installation process is straightforward and requires basic electrical knowledge, making it suitable for DIY enthusiasts. The fixture comes with all the necessary hardware for installation, including expansion bolts, hex screws, and wire connectors.

Installation Guide
ON
© VONN Lighting,2019
Model: VOB14638
Parts List
A.
B. Expansion Bolt x 2
C.
D.
E.
A
B
C
D
E
Circuit Box
Base Plate
Hex Screws x 3
Wire Connectors x 4
Hex Wrench
Make sure that you have all necessary parts by checking the parts list. If
any part is missing or damaged, please contact VONN Lighting
Customer Service at 888-604-8666 for a replacement.
Please read and comprehend the entire manual before attempting to
assemble, operate, or install the product.
VONN highly recommends to use a qualified, licensed electrician to install
the fixture.
LED INFO & WARNINGS
•
•
All parts must be used as indicated in these instructions. Do not substitute
any parts, leave parts out, or use any parts that are worn or broken.
•
Inspect the LED fixture prior to installation to make sure that it has not
been damaged during shipping.
•
Please handle the LED light with care when unpacking. Do not apply
pressure to the LEDʼs, do not open any factory sealed compartments, and
do not touch the LEDs with your hands.
•
Shut “OFF” the electricity at main fuse box.
•
•
Do not remove or replace VONN manufactured parts that are provided
with the fixture.
VONN Lighting
Tools You May Need
GOGGLES
TAPE MEASURE
RUBBER
GLOVES
PHILLIPS
WRENCH
DRILL
SCREW DRIVER
6 5/8”
5 4/5”
3/8”
(10mm)
7/8”
19.7
º
(22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)
10 1/8”
(257mm)
1 3/8”
(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
1 3/4”
(
45mm)
1 15/16”
(
50mm)
9/16”-18UNEF
27mm ~ 41.3mm
1 1/16” ~ 1 5/8”
1 15/16”
(
50mm)
12 7/16”
(316mm)
1 5/8”
(42.5 mm Max)
7A
8B
8C
8D
8A
7A
8B
8C
8D
8A
12V AC Low Voltage Fixture (TRANSFORMER IS REQUIRED)
•
© VONN Lighting,2019
A
B
Legend
L = Live/Hot/Black
N = Neutral/White
= Ground/Green
•Install base plate (A) onto concrete floor with expansion bolts (B). Secure with flat
washers, lock washers, and nuts.
Concrete Floor
1.Nut
2.Lock Washer
3.Flat Washer
2. Supply Wires:
Ground Wires:
Bring power wires to fixture location in accordance to local
electrical codes.
Connect White (Neutral Wire) from fixture to power White
(Neutral Wire).
Connect Green (Ground Wire) from fixture to supply Green
(Ground Wire).
Twist wires together clockwise and secure with wire
connector (D).
Installer Tip (1): Nut, lock washer, and flat washer are
attached to expansion bolt.
3. Install Bollard
Install fixture to base plate (A). Secure fixture with hex screw
(C). Tighten hex screw (C) with hex wrench (E).
ON
ON
Circuit Box
4. Turn Power ON
Turn electricity “ON” at main fuse box.
1. Install Base Plate
Connect Black (Line Wire) from fixture to power Black (Hot
Wire).
•
•
•
•
•
•
•
L
N
D
C
E
Installation Hole Size
  • Page 1 1
  • Page 2 2

VONN Lighting VOB14638BL Installation guide

Brand
VONN Lighting
Model
VOB14638BL
Type
Installation guide

VONN Lighting VOB14638BL is a 12V AC Low Voltage LED bollard fixture, which can be used for outdoor lighting applications. It features a sturdy construction with a concrete base plate and a metal fixture, ensuring durability and weather resistance. The fixture emits a warm white light, creating a welcoming and inviting ambiance. The installation process is straightforward and requires basic electrical knowledge, making it suitable for DIY enthusiasts. The fixture comes with all the necessary hardware for installation, including expansion bolts, hex screws, and wire connectors.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers