Riva RC2103HD-6511 Installation guide

Brand: Riva

Model: RC2103HD-6511

Category: Security cameras

Type: Installation guide

www.rivatech.de

Specification subject to change without notice

RC2103HD-6511

Installation Guide

Precaution

 Please read this manual carefully before installing the unit.

 Never disassemble the camera. Unauthorized disassembly may cause equipment

failure or damage to the unit.

 Please do not install the camera in a place exposed to direct sunlight.

 Do not operate the camera in environments beyond the specified temperature.

Refer to Environment Condition on APPENDIX (A): SPECIFICATIONS in this manual.

 Before applying power to the camera, check the power source to ensure that it is

within the specifications. Refer to Electrical Characteristics on APPENDIX (A):

SPECIFICATIONS.

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 3

Table of Contents

Precaution ................................................................................................................ 2

1. FEATURES ............................................................................................................. 4

2. PACKAGE CONTENTS............................................................................................. 5

3. PART NAMES ........................................................................................................ 6

4. INSTALLATION ...................................................................................................... 7

4.1. Installing the camera .......................................................................................................... 7

4.1.1. Semi-Flush Mount ....................................................................................................... 7

4.1.2. Flush Mount ................................................................................................................ 9

4.1.3. Compatible Accessories ............................................................................................ 11

4.2. Setting the Image Attributes ............................................................................................ 12

5. CONNECTIONS .................................................................................................... 13

6. CONFIGURATION ................................................................................................ 17

6.1. Set up network environment ........................................................................................... 17

Generic IP Environment ...................................................................................................... 17

Custom IP Environment ...................................................................................................... 18

6.2. View video on web page .................................................................................................. 19

6.1.1. ActiveX Installation .................................................................................................... 19

6.2.2. View video using IPAdmin Tool ................................................................................. 20

6.3. Reboot .............................................................................................................................. 21

6.4. Factory Default ................................................................................................................. 21

6.5. Safe Mode ........................................................................................................................ 21

APPENDIX (A): SPECIFICATIONS .............................................................................. 23

Summary ................................................................................................................................. 23

Electrical Characteristics ......................................................................................................... 24

Environment Condition ........................................................................................................... 24

Mechanical Condition ............................................................................................................. 24

APPENDIX (B): POWER OVER ETHERNET ................................................................. 25

Power Comparison .................................................................................................................. 25

APPENDIX (C): DIMENSIONS ................................................................................... 26

APPENDIX (D): HEXADECIMAL-DECIMAL CONVERSION TABLE ................................. 27

REVISION HISTORY ................................................................................................. 29

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 4

1. FEATURES

Camera

 1/2.5” 5 Megapixel CMOS Image Sensor

 Wide view (180°) angle

 Digital Day/Night

 WDR

Video

 H.264 Baseline, Main, High profile(MPEG-4 Part 10/AVC), MJPEG(Motion JPEG)

 Max 14fps in 4:3 mode

Max 30fps in 16:9 mode*

 Text Overlay

Audio

 Two-way Audio Streaming

 G.711µLaw

Network

 10/100 Base-T Ethernet

Integration

 Software Development Kit (SDK) available

 ONVIF Compliant (Profile S & Profile G)

* ONVIF Profile G is supported from FW V1.8.0 or higher.

General

 microSD/SDHC slot

 Power Over Ethernet (PoE)

Video Contents Analytics (VCA)

 VCA Presence (Standard)

 VCA Surveillance (Optional)

 VCA Pro(Optional)

* VCA Pro is supported from FW V1.8.0 or higher.

* If VCA is activated, frame rate is limit to max15fps@1080p. Limitation based on V.1.9.0

firmware release and could be changed without notice.

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 5

2. PACKAGE CONTENTS

Please unpack the package carefully and handle the equipment with care.

The package contains:

Camera

DC Power Adaptor

Universal Plugs

Quick Installation Guide

Terminal Blocks

FMB mount (for flush mount)

Screws and Anchor Blocks

Cable Hole Cap

DC Power Jack Cable

Installation Template

Note

The contents above are subject to change without prior notice.

(M4x30)

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 6

3. PART NAMES

① Reset Button

This button will restart the device or reset it to factory default settings. Refer to 6.3. Reboot and

6.4. Factory Default for more details.

② PAL/NTSC Button

Pressing the button cycles through PAL, NTSC, and no video output mode: No video output -> PAL->NTSC

③ Terminal Connector

Connector for cable connection of video output, audio input/output and digital input/output.

Refer to 5. CONNECTIONS for more details.

④ LAN Connector

RJ45 LAN connector for 10/100 Base-T Ethernet(PoE supported)

⑤ microSD / SDHC Slot

The camera supports up to 32GB. Class 4 and higher SD card is recommended for HD recordings.

⑥ Power Adapter Connector

DC 12V power supply connection

②

③

⑤

⑥

* Models and their appearance are subject to change without any prior notice.

④

①

*The reset button is located under this plate.

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 7

4. INSTALLATION

4.1. Installing the camera

4.1.1. Semi-Flush Mount

Installation Template

(Unit: mm)

Caution

Installation template’s image size scale in this installation guide is not 1:1.

The correct-size template design paper can be found inside the package

separately.

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 8

1) Place the installation template included

in the package on the desired installation

surface.

2) Drill holes on the correct spots based on

the template paper, and insert the anchor

blocks into the holes.

3) Open the dome cover.

*Refer to the caution below for the details of

how to open the cover.

4) Connect necessary cables including a

LAN cable and a power cable to the

camera.

5) Hold the camera against the surface

where the camera will be mounted by

matching the alignment holes with the

corresponding anchor blocks.

6) Route the cables through the cable hole

at the bottom of the camera, and tighten

the anchor blocks with the screws.

7) Attach the dome cover on the main

body, and lock it up by rotating the dome

cover.

*Refer to the caution below for the details of

how to attach the dome cover.

Caution

When placing the dome cover, look for the carved triangle mark on both dome

cover and main body. Both triangles should be aligned together when placing the

cover. Once the cover has been placed, rotate the dome cover clockwise for a

secure lock. To detach the cover, rotate the cover counterclockwise. Then, align

the two triangle marks each other, and pull the cover.

Caution

To prevent products from damage, place the camera on a stable and

non-vibrating surface. If the stability is in doubt, consult safety personnel for

reinforcements, and then proceed with the installation.

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 9

4.1.2. Flush Mount

(Unit: mm)

Caution

Installation template’s image size scale in this installation guide is not 1:1.

The correct-size template design paper can be found inside the package

separately.

Installation template (FMB)

21 V1.0

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 10

1) Place the installation template included

in the package on the desired installation

surface.

2) Drill holes on the correct spots based on

the template paper, and insert the anchor

blocks into the holes.

3) Open the dome cover.

*Refer to the caution below for the details

about how to open the cover.

4) Connect necessary cables including a

LAN cable and a power cable to the

camera.

5) Unscrew the three bolts attached on the

dome cover’s surface, and place the FMB

mount between the dome shell and the

bottom circular cylinder. Then, align the

three screw holes on each component

together, and tighten the three

components with the bolts included in the

package.

6) Attach the three components-combined

dome cover to the main body, and lock it

up by rotating the cover.

*Refer to the caution below for the details

about how to lock the cover.

7) Tighten the camera’s body into the

mounting surface’s anchor blocks by

inserting the screws included in the

package through the screw holes around

the edge of the FMB mount.

Caution

When placing the dome cover, look for the carved triangle mark on both dome

cover and main body. Both triangles should be aligned together when placing the

cover. Once the cover has been placed, rotate the dome cover clockwise for a

secure lock. To detach the cover, rotate the cover counterclockwise. Then, align

the two triangle marks each other, and pull the cover.

Caution

To prevent products from damage, place the camera on stable and non-vibrating

surfaces. If the stability is in doubt, consult safety personnel for reinforcements,

and then proceed with the installation.

circular cylinder

FMB mount

dome shell

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 11

4.1.3. Compatible Accessories

The various combinations of the compatible accessories to mount this camera model are as

follows.

Model Names & Combinations

WMB-3000 + (CMA-U100 or PMA-U100)

WMB-3000P + PMC-3000 + (JBK-U100) + (CMA-U100 or PMA-U100)

CMB-3000P + PMC-3000

GBA-3000

Refer to the corresponding accessory model’s installation guide for the instructions.

Note

The models in the parenthesis, (), may or may not be required depending on

the installation environment.

Model Image

WMB-3000

WMB-3000P

CMB-3000P

PMC-3000

WMB-3000/CMB-3000

This guide i llustrates how to asse mble the corner mount adapter and

pole mount adapter.

Check the let ter of the alphabet assi gned to each adapter and tighten

the screws in the corresponding holes to assemble the adapter.

A-A-A(M4TAP)

IPE-3500

IPE-2100

IPN-2102

IPN-3102

IPN-3502

IPE-3100

A-A-A : IPN3202HD

B-B : IPN352HD & IPX5502HD

C-C : IPN3402HD

D-D-D : IPN2103HD & IPN3102HD & IPN3502HD

A C

JBK-U100

CMA-U100

PMA-U100

GBA-3000

A-A-A : IPN6802HD

B-B-B : IPN6702HD

C-C-C-C : IPN6602HD

D-D-D-D : WMB-3000P & CMB-3000P

HOUSING COVER에 WALL MOUNT CABLE을 통과시킨다.

HOUSING COVER와 WALL MOUNT BRACKET을 조립한다

결합 후 상태 이미지

3mm Hex Wrench를 사용하여 볼트를 푼다. (4EA 동일 방법)

Hinge를 젖힌 후 빼낸다. (2EA 동일 방법)

BULLET CAMERA의 CABLE을 HOUSING COVER에 통과시킨다.

장착하는 CAMERA에 맞는 BOLT를 사용하여

CABLE을 GASKET에 끼운 후 위치에 맞게 삽입한다.

CABLE을 GASKET에 맞춰 정리한 후 GASKET을 접어 닫는다.

M3x12 BOLT를 사용하여 PLATE를 조립한다.

왼쪽 상세 이미지를 참고 하여 CABLE GLAND 를 조립한다.

CABLE GLAND를 HOUSING COVER에 완전히 조립한다.

HOUSING COVER의 LOWER와 UPPER를

HOUSING COVER의 UPPER와 LOWER를

A A

C C

D D

PMA-U100 CMA-U100 WMA-U100

M5x12 BOLT를 사용하여 HOUSING COVER와 PMA-U100을 체결한다.

결합 후 상태 이미지

M5x12 BOLT를 사용하여 HOUSING COVER와 CMA-U100을 체결한다. M5x12 BOLT를 사용하여 HOUSING COVER와 WMA-U100을 체결한다.

결합 후 상태 이미지 결합 후 상태 이미지

이미지와 같이 위치 시킨 후 HINGE를 사용하여 체결한다.

3mm Hex Wrench를 사용하여 볼트를 조인다. (4EA 동일 방법)

E E

E-E-E : ODE-1000T

HOUSING COVER에 조립한다.

PMA-U100/CMA-U100

This guide illustrates how to assemble the corner mount adapter and

pole mount adapter.

Check the letter of the alphabet assigned to each adapter and tighten

the screws in the corresponding holes to assemble the adapter.

A-A-A(M4 PAM)

IPN6802HD

B-B-B(M4 PAM)

IPN6702HD

C-C-C-C(M5 PAM)

IPN6602HD

D-D-D(M6 PAM)

ODE-1000T

E-E-E-E(M6 PAM)

WMB-3000P & CMB-3000P

F-F-F-F(M5 PAM)

JBK-U100

PMA-U100/CMA-U100

This guide illustrates how to assemble the corner mount adapter and

pole mount adapter.

Check the letter of the alphabet assigned to each adapter and tighten

the screws in the corresponding holes to assemble the adapter.

A-A-A(M4 PAM)

IPN6802HD

B-B-B(M4 PAM)

IPN6702HD

C-C-C-C(M5 PAM)

IPN6602HD

D-D-D(M6 PAM)

ODE-1000T

E-E-E-E(M6 PAM)

WMB-3000P & CMB-3000P

F-F-F-F(M5 PAM)

JBK-U100

G-G-G-G(M6 PAM)

WMB-3000 & WMB-3000S

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 12

4.2. Setting the Image Attributes

On the camera’s webpage, users can configure the image attributes. The menu of the image

attributes is available at Video Appearance via the path, Setup > Video & Audio > Camera.

The following features can be adjusted: Brightness, Contrast, Saturation, and Sharpness.

For more detailed information, refer to the provided “RIVA Web Interface Manual Full HD

Line”.

All Manual’s and Installation Guides can downloaded from www.rivatech.de homepage.

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 13

5. CONNECTIONS

① Audio connection

The camera provides a mono audio input and output. Due to low audio output power, an

amplified speaker is recommended for enhanced sound. (Refrain from connecting a

headphone or an earphone directly to the camera)

Mic

Amp Speaker

ETHERNET

MICRO SD

DC12V

OutOut

VIDEO

C C

AUDIO

Reset

SW1 SW2 SW3

SW5 SW6

N / A N / A

SW1

SW2

SW3

SW4

SW5

SW6









ETHERNET

MICRO SD

DC12V

OutOut

VIDEO

C C

AUDIO

Reset

SW1 SW2 SW3

SW5 SW6

N / A N / A

SW1

SW2

SW3

SW4

SW5

SW6



⑥

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 14

② Sensor (DI) connection

Sensor (DI) can be connected to either a voltage type sensor or a relay type sensor like the

following figures. Settings can be done through the camera's webpage.

Input voltage range: 0VDC minimum to 5VDC maximum, Max 50mA

Caution

Do not exceed the maximum input voltage or relay rate.

③ Alarm (DO) connection

Only the relay type is supported.

Relay Rating: Max 24VDC 50mA

Caution

Do not exceed the maximum relay rating.

COM

Relay Type

Device

Internal

+3.3V

COM

Relay Type

Voltage Type

Output of

Sensor

Output of

Sensor

Internal

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 15

④ Analog Video Out Connection

Use 75 ohm video coaxial cable to connect to a monitor's analog video input and check the

camera's connection and its image focus at the installation site. Be sure to press the output

configuration button (PAL/NTSC button) to see the video (Refer to 3. PART NAMES to check

the location of the PAL/NTSC button). The factory default is 'no video output'; Press once to

set the video to PAL, and press again to set the video to NTSC. Pressing the button again will go

back to 'no video output' mode, disabling the viewing through the analog video connection.

Note

Once the PAL/NTSC button is pressed, the video display lasts for 3 minutes

before it goes back to ‘no video output’ mode.

⑤ LAN connection

This is a RJ45 LAN connector for 10/100 Base-T Ethernet. Use the Ethernet cable (RJ45) to

connect the device to a hub or a router in the network. When the LAN cable is connected, the

orange LED light will become solid and green LED will blink every 250 millisecond. Refer to

Appendix (B). Power over Ethernet for more details.

Video

GND

Red

Black

Green LED Orange LED

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 16

⑥ Power Connection

The camera can be powered from either 12VDC or PoE. If the camera is powered via PoE, refer

to Appendix (B). Power over Ethernet for more details. To operate your camera using 12VDC,

make sure the polarity is correct before connecting the power cable. Incorrect connection may

cause damages to the device.

12V

Red

Black

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 17

6. CONFIGURATION

6.1. Set up network environment

The default IP address of the device is 192.168.XXX.XXX. Users can identify the IP address of the

device from converting the MAC address’s hexadecimal numbers, which is attached to the

device. Be sure that the device and PC are on a same area network before running the

installation.

IP address : 192.168.xxx.xxx

Subnet mask: 255.255.0.0

Generic IP Environment

In case of generic private network environment where IP address 192.168.XXX.XXX are used,

users may view the live streaming images on a web page using the device’s default IP address:

1. Convert the device’s MAC address to the IP address. Refer to the Hexadecimal-Decimal

Conversion Chart at the end of the manual.

(The MAC address of the device is attached on the side or bottom of the device.)

2. Start the Microsoft® Internet Explorer web browser and enter the address of the device.

3. Web streaming and device configurations are supported through ActiveX program. When the

ActiveX installation window appears, authorize and install the ActiveX.

MAC address = 00-13-23-01-14-B1 → IP address = 192.168.20.177

Convert the last two sets of hexadecimal numbers to decimal numbers.

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 18

Custom IP Environment

IPAdminTool and the manual can download from www.rivatech.de homepage.

IPAdminTool is a management tool, which automatically scans all of the network products for

users to perform administrative tasks, which includes network configurations, firmware update,

device reboot, and device organizations.

To modify the device’s default IP address for customized network area:

1. Find the device from the IPAdminTool’s list and highlight the device’s name.

2. Right-click the mouse and select IP Address; IP Setup window appears.

3. In the IP Setup’s window, information under Local Network information displays the

user/PC’s network area information. Those information need to be incorporated to the IP

Address, Subnet Mask, Gateway, and DNS boxes, except the last 2 sets of IP Address, which

are to be the unique numbers for the device. Refer to the image above for the setting

4. Click Setup to complete the modification.

PC environment Info

Give new unique IP

address in last two sets

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 19

6.2. View video on web page

Type the proper IP address to view the live streaming images through a web browser.

The default username and password is root / pass.

6.2.1. ActiveX Installation

1. When the browser asks to install the AxUMF software, click Install to proceed.

3. When Setup installation pop-up window appears, click Install to proceed with rest of

installations.

Note

Depending on system OS and Internet Explorer version, installation experience

may differ from one another. Figures described above are from Windows 7,

Internet Explorer 9 environment.

HD Series RC2103HD-6511 Installation Guide

01-2015-A www.rivatech.de 20

Caution

6.2.2. View video using IPAdmin Tool

1. From the IPAdminTool’s product list, select the device by highlighting it.

2. Right-click the mouse and select Web View.

3. The system’s default web browser opens the device’s address.

Whether directly accessing the streaming video through typing IP address on a

web page or taking steps through IPAdminTool, the ActiveX is needed to be

installed for the Microsoft® Internet Explorer to have the complete

configuration privileges.

More Information

To learn more about using other features of your devices, refer to the manuals as “RIVA Web

Interface Manual Full HD Series” or “VCAsys User Manual (Online Help)”, which is available on

www.rivatech.de homepage.

Page is loading ...

Riva RC2103HD-6511 Installation guide

Brand: Riva

Model: RC2103HD-6511

Category: Security cameras

Type: Installation guide

Download PDF

report

Riva RC2103HD-6511 Installation guide

Riva RC2103HD-6511 Installation guide

Related papers

Other documents