Rainbow Garden Products R355 Installation guide

Brand
Rainbow Garden Products
Model
R355
Type
Installation guide

Rainbow Garden Products R355 is a versatile and easy-to-use extra-wide garden arch that is perfect for supporting climbing plants and creating a beautiful focal point in your garden. With its sturdy construction and adjustable width, the R355 can accommodate a variety of plant sizes and shapes.

The arch is constructed from durable steel tubing with a powder-coated finish for weather resistance. The eight straight tubes are connected by "T" joints, and the top curved tubes and width extensions are secured with struts. The arch can be adjusted in width from 1.52m (5') to 2.28m (7'6") to accommodate different plant sizes and spacing.

Rainbow Garden Products R355 is a versatile and easy-to-use extra-wide garden arch that is perfect for supporting climbing plants and creating a beautiful focal point in your garden. With its sturdy construction and adjustable width, the R355 can accommodate a variety of plant sizes and shapes.

The arch is constructed from durable steel tubing with a powder-coated finish for weather resistance. The eight straight tubes are connected by "T" joints, and the top curved tubes and width extensions are secured with struts. The arch can be adjusted in width from 1.52m (5') to 2.28m (7'6") to accommodate different plant sizes and spacing.

Extra-Wide
Garden Arch
Assembly Instructions
07725
Components Supplied
Tools Required (not supplied)
Phillips cross-head screwdriver
Mallet
Tape Measure
Before You Start
•Layout all of the component parts and
make sure you have all of the parts listed.
• When you are ready to start, make sure
that you have the right tools to hand,
plenty of space and a clean dry area for
assembly. Always try to assemble the
product as close as possible to the
intended location.
•Remove all plastic bags and dispose of
safely.
•Retain the instructions for future use.
Caution
This pack contains small items which should
be kept away from children.
Consumer Helpline
If you have any problems or queries with
this product then please contact our
helpline number: 01406 372227,
or write to: Gardman Ltd. High Street,
Moulton, Spalding, Lincs, PE12 6QD.
Fax: +44 (0) 1406 372233.
Ref Description Illustration Qty
AStraight tube 8
BT joints 14
C Moisture 12
protection
sleeve
DTop left 2
Curved tubes
ETop right 2
Curved tubes
FStruts 8
GGround hole 1
maker
H Assembly 14
screws
IArch width 2
extensions
Size: 95cm (3'
1
/
2
")
(approx.)
Size: 54cm (1'9")
(approx.)
Size: 41.5cm (1'4")
(approx.)
1. Slide the "T" joints (B) over the straight
tubes (A) and fit moisture protection
sleeves (C) as illustrated to assemble the
eight straight tubes (A). Slide the
moisture protection sleeve half way onto
the female (upper) joint before pushing
the male (lower) joint into it. Do not
secure 'T' joints with assembly screws (H)
until you have carried out section 5
below to allow for final adjustments.
2. Fit the top curved tubes (D, E) and width
extensions (I) in a similar way ensuring
that the "T" joints are positioned as
illustrated with joint/moisture protection
sleeves fitted. Please also ensure that the
curved tubes are fitted the correct way
round to form a perfect arch. The width
extensions may be cut with a hacksaw to
reduce the width of the arch if required.
3. Connect both halves of the arch with
struts (F) by pushing the struts into
lateral (vacant) slots of "T" joints.
4. Place arch in desired location and mark
leg positions on the ground. Remove
arch and drive ground hole maker (G) to
0.38m deep (1' 3"). Remove hole maker
and repeat for remaining legs. Insert legs
into holes and push home. Firm earth
around legs.
5. Carry out final adjustments to strut
positions and secure "T" joints to tubes
using assembly screws (H)
Helpful hints:
You may find it easier to assemble your
arch horizontally on its side and then
carefully stand it upright to install.
Soaking the moisture protection sleeves
in warm water for a few minutes prior to
fitting will make them more malleable
and will aid fitting.
Please note: “T” joints (B) should be
positioned either above or below the
straight tube connection points: do not
attempt to use the “T” joints (B) to
connect the straight tubes (A) together.
Assembly
0.38m
D
A
B
C
G
Joint
Moisture
Protection
Sleeve
F
C
1.52m
(5')
0.47m
(1'6
1
/
2
")
1.9m
(6'3")
0.38m
(1'3")
All sizes approx.
BELOW GROUND
HEIGHT ABOVE
GROUND
DEPTH
WIDTH
TOTAL HEIGHT BEFORE FITTING:
2.28m
(
7
'
6
")
EI
  • Page 1 1
  • Page 2 2

Rainbow Garden Products R355 Installation guide

Brand
Rainbow Garden Products
Model
R355
Type
Installation guide

Rainbow Garden Products R355 is a versatile and easy-to-use extra-wide garden arch that is perfect for supporting climbing plants and creating a beautiful focal point in your garden. With its sturdy construction and adjustable width, the R355 can accommodate a variety of plant sizes and shapes.

The arch is constructed from durable steel tubing with a powder-coated finish for weather resistance. The eight straight tubes are connected by "T" joints, and the top curved tubes and width extensions are secured with struts. The arch can be adjusted in width from 1.52m (5') to 2.28m (7'6") to accommodate different plant sizes and spacing.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents