LARSON 36023032 is a high-quality storm door that offers a range of features for enhanced durability, energy efficiency, and ease of use. Constructed with a sturdy aluminum frame and reinforced corners, this storm door can withstand harsh weather conditions and provides added security for your home. The included closer ensures a smooth and quiet operation, while the glass insert allows for natural light to enter your home. Installation is made simpler with the included EasyHang® feature, which enables quick and easy alignment and attachment of the door to your door frame.
LARSON 36023032 is a high-quality storm door that offers a range of features for enhanced durability, energy efficiency, and ease of use. Constructed with a sturdy aluminum frame and reinforced corners, this storm door can withstand harsh weather conditions and provides added security for your home. The included closer ensures a smooth and quiet operation, while the glass insert allows for natural light to enter your home. Installation is made simpler with the included EasyHang® feature, which enables quick and easy alignment and attachment of the door to your door frame.
Slide rail extender (marked with “L”) into
the bottom of the hinge rail.
4a
Slide rail extender to sill. Loosen hinge rail
screw as needed, and retighten screw after
lowering extender.
Pre-drill hole and install screw on the
bottom outer side of hinge rail to secure
door in opening. Do not overtighten.
4c 4d
Attach Storm Door to Door Frame
4
4e 4f
Attach Hinge Rail to Storm Door
3
3a
3c 3d
3b
Place interior side face up.
Drill remaining pilot holes.
Attach remaining screws starting from the bottom.
4b
TOP END OF DOOR
INTERIOR OF DOOR
Hang storm door onto door frame using the
placeholder screw. The door will settle
approx. 1/16-in down.
Tighten screw
while pushing top of hinge rail tight
against the door frame.
PUSH
TOP END OF DOOR
INTERIOR OF DOOR
Painted, Actual size
1/8-in
#8x1-in
Painted, Actual size
1/8-in
#8x1-in
Install the Drip Cap
5
Place the drip cap on the door
frame above the storm door.
5a 5b
Pre-drill holes and install screws.
5c
Caulk if desired.
5d
4g
Cut extender weather stripping to length,
peel adhesive backing and install.
Close door to verify consistent clearance.
Align drip cap to end of hinge rail.
Push door tight against door frame, then pre-drill holes
and install screws on the outer side of hinge rail starting
with the top screw.
Do not over tighten screws.
Pre-drill holes and place screws on the inner side of hinge
rail In all 8 locations. Do not over tighten screws.
Painted, Actual size
1/8-in
#8x1-in
Install Latch Rail
6
Finishing Touches
7
Slide rail extender (marked with “R”) into the bottom of
latch rail.
Place latch rail tight against the drip cap. Slide rail extender to sill.
6a 6b
Align outside edge of latch rail with outside edge of drip
cap. Verify that the door closes freely without hitting the
latch rail.
6d
Pre-drill holes and fasten the latch rail with screws.
6e
6c
6f
Cut extender weather stripping to length,
peel adhesive backing and install.
Painted, Actual size
1/8-in
#8x1-in
7a
Latch Hardware
Follow the instructions in the storm door handle kit.
8a
Glass/Screen Insert Removal
Retract all four screen latches and remove the inserts.
7d
Expander
Drill two 3/32-in pilot holes. Do not drill through to the front of the storm door.
Secure expander.
STOP
Extended Retracted
7e
Closer
Follow the instructions in the closer kit.
7b
Expander
Slide expander onto door.
3/32-in
#6x3/8-in
Actual size
7c
Expander
Adjust the expander until the sweep lightly contacts the
threshold.
Glass / Screen Insert
8
8b
Glass/Screen Insert Installation
Install glass insert with weatherstripping facing away from you. Install screen insert. Extend all four screen latches.
(Screen may be installed without glass panel.)
3b
Note: The hinge rail will overlap
the top of the door by 1/8-in.
Installation Instructions
Left Hinge
Please turn poster over for Right Hinge Instructions.
© 2015 Larson Manufacturing
Read the complete installation instructions before proceeding with installation.
• Installation may require two people when lifting and installing the door
• Use appropriate protective equipment
• Children should not be allowed to play with the door
• Failure to install door properly could result in an injury
NOTE: Larson Manufacturing Company is not responsible for accidents and
injury resulting from the use or installation of this product.
Please have the following information
on hand when you call:
1 Warranty Registration number
2 Model of door
3 Size of the door
4 Color
VISIT WWW.LARSONDOORS.COM
HOMEOWNER HELPLINE
1-888-483-3768
INSTALLATION
QUESTIONS?
MISSING PARTS?
REPLACEMENT PARTS?
Parts List
WARRANTY REG# DO NOT REMOVE
00000000.000 00 00 00
Left and Right Rail Extender
With Weather Strips
Hinge Rail
Registration Number
Drip Cap
Latch Rail
Expander with sweep
Handle Kit
Closer Kit and Installation Screws
Recommended Tools
1
Prep Steps
1c 1d
Check for existing door hardware interference. A minimum depth of 2-3/4-in is required from the storm
door mounting surface to the entry door handle.
If storm door hardware interferes with your primary door hardware, you may shift the
storm door handle up or down, or install storm door with hinge on opposite side.
Verify house door trim is securely attached and square.
1b
1-in wide x 1-in deep mounting surface is required. Hinge-side
shimming may be required to fit existing opening. Use an
appropriate shim thickness to reduce the opening to size noted.
Shims are not included – household shim materials may include
paint stir sticks or wooden yardsticks.
1-in
1-in
TOP VIEW
Exterior Brick
Mold Trim
Storm Door Opening Width
Jamb
Interior House Door
Nominal
Door Sizes
Opening Width
(no shim required)
Opening Width
(shim required)
Shim to this
Opening Width
Min. – Max.
Height
30-in x 81-in 29 7/8-in – 30-in 30 1/16-in – 30-3/8-in 29 7/8-in – 30-in
80-in
to
81-in
32-in x 81-in 31 7/8-in – 32-in 32 1/16-in – 32-3/8-in 31 7/8-in – 32-in
34-in x 81-in 33 7/8-in – 34-in 34 1/16-in – 34-3/8-in 33 7/8-in – 34-in
36-in x 81-in 35 7/8-in – 36-in 36 1/16-in – 36-3/8-in 35 7/8-in – 36-in
1a
Confirm the hinge side of the storm door. Turn
this poster over for right hinge
installation. Your LARSON Reversa-Hinge
storm door is designed for either right or left
hinge installation. Oversize custom doors may
not be reversible.
Left Hinge
weather stripping
Set Placeholder Screw For Hinge Rail
2
2a 2b 2c
Place the hinge rail tight against the left side of door
frame and slide to top.
Leave 1/8-in of screw exposed.
Use FIRST hole from top only. Mark hole with pencil,
remove hinge rail, pre-drill and attach placeholder screw as
shown. Do not tighten all of the way.
Locate factory installed hinge locator hole near top
end of door, and place hinge rail as shown.
Attach #10 x 1/2-in screw into pilot hole.
Actual size
1/8-in
#10 x 1/2-in
Painted, Actual size
1/8-in
#8x1-in
Scan with mobile device to see a video of
EasyHang
®
installation.
Escanee con el dispositivo móvil para ver un video
de la instalación EasyHang
®
Storm Door
202220849-0415 NuVent Ext
Slide rail extender (marked with “R”) into
the bottom of the hinge rail.
4a
Slide rail extender to sill. Loosen hinge rail
screw as needed, and retighten screw after
lowering extender.
Pre-drill hole and install screw on the
bottom outer side of hinge rail to secure
door in opening. Do not overtighten.
4c 4d
Attach Storm Door to Door Frame
4
4e 4f
4b
Hang storm door onto door frame using the
placeholder screw. The door will settle
approx. 1/16-in down.
Tighten screw
while pushing top of hinge rail tight
against the door frame.
PUSH
Painted, Actual size
1/8-in
#8x1-in
Painted, Actual size
1/8-in
#8x1-in
4g
Cut extender weather stripping to length,
peel adhesive backing and install.
Push door tight against door frame, then pre-drill holes
and install screws on the outer side of hinge rail starting
with the top screw.
Do not over tighten screws.
Pre-drill holes and place screws on the inner side of hinge
rail In all 8 locations. Do not over tighten screws.
Install the Drip Cap
5
Place the drip cap on the door
frame above the storm door.
5a 5b
Pre-drill holes and install screws.
5c
Caulk if desired.
5d
Close door to verify consistent clearance.
Align drip cap to end of hinge rail.
Painted, Actual size
1/8-in
#8x1-in
Install Latch Rail
6
Slide rail extender (marked with “L”) into the bottom of
latch rail.
Place latch rail tight against the drip cap. Slide rail extender to sill.
6a 6b
Align outside edge of latch rail with outside edge of drip
cap. Verify that the door closes freely without hitting the
latch rail.
6d
Pre-drill holes and fasten the latch rail with screws.
6e
6c
6f
Cut extender weather stripping to length,
peel adhesive backing and install.
Painted, Actual size
1/8-in
#8x1-in
8a
Glass/Screen Insert Removal
Retract all four screen latches and remove the inserts.
Extended Retracted
Glass / Screen Insert
8
8b
Glass/Screen Insert Installation
Install glass insert with weatherstripping facing away from you. Install screen insert. Extend all four screen latches.
(Screen may be installed without glass panel.)
© 2015 Larson Manufacturing
Read the complete installation instructions before proceeding with installation.
• Installation may require two people when lifting and installing the door
• Use appropriate protective equipment
• Children should not be allowed to play with the door
• Failure to install door properly could result in an injury
NOTE: Larson Manufacturing Company is not responsible for accidents and
injury resulting from the use or installation of this product.
Please have the following information
on hand when you call:
1 Warranty Registration number
2 Model of door
3 Size of the door
4 Color
VISIT WWW.LARSONDOORS.COM
HOMEOWNER HELPLINE
1-888-483-3768
INSTALLATION
QUESTIONS?
MISSING PARTS?
REPLACEMENT PARTS?
Parts List
WARRANTY REG# DO NOT REMOVE
00000000.000 00 00 00
Left and Right Rail Extender
With Weather Strips
Hinge Rail
Registration Number
Drip Cap
Latch Rail
Storm Door
Expander with sweep
Handle Kit
Closer Kit and Installation Screws
Recommended Tools
1
Prep Steps
1c 1d
Check for existing door hardware interference. A minimum depth of 2-3/4-in is required from the storm
door mounting surface to the entry door handle.
If storm door hardware interferes with your primary door hardware, you may shift the
storm door handle up or down, or install storm door with hinge on opposite side.
Verify house door trim is securely attached and square.
1b
1-in wide x 1-in deep mounting surface is required. Hinge-side
shimming may be required to fit existing opening. Use an
appropriate shim thickness to reduce the opening to size noted.
Shims are not included – household shim materials may include
paint stir sticks or wooden yardsticks.
1-in
1-in
TOP VIEW
Exterior Brick
Mold Trim
Storm Door Opening Width
Jamb
Interior House Door
Nominal
Door Sizes
Opening Width
(no shim required)
Opening Width
(shim required)
Shim to this
Opening Width
Min. – Max.
Height
30-in x 81-in 29 7/8-in – 30-in 30 1/16-in – 30-3/8-in 29 7/8-in – 30-in
80-in
to
81-in
32-in x 81-in 31 7/8-in – 32-in 32 1/16-in – 32-3/8-in 31 7/8-in – 32-in
34-in x 81-in 33 7/8-in – 34-in 34 1/16-in – 34-3/8-in 33 7/8-in – 34-in
36-in x 81-in 35 7/8-in – 36-in 36 1/16-in – 36-3/8-in 35 7/8-in – 36-in
Scan with mobile device to see a video of
EasyHang
®
installation.
Escanee con el dispositivo móvil para ver un video
de la instalación EasyHang
®
Installation Instructions
Right Hinge
Please turn poster over for Left Hinge Instructions.
1a
Confirm the hinge side of the storm door.
Turn this poster over for left hinge
installation. Your LARSON Reversa-Hinge
storm door is designed for either right or left
hinge installation. Oversize custom doors
may not be reversible.
Right Hinge
weather stripping
Set Placeholder Screw For Hinge Rail
2
2a 2b 2c
Place the hinge rail tight against the right side of door
frame and slide to top.
Use FIRST hole from top only. Mark hole with pencil,
remove hinge rail, pre-drill and attach placeholder screw as
shown. Do not tighten all of the way.
Painted, Actual size
1/8-in
#8x1-in
Attach Hinge Rail to Storm Door
3
3a
3c 3d
3b
Place interior side face up.
Drill remaining pilot holes.
Attach remaining screws starting from the bottom.
TOP END OF DOOR
TOP END OF DOOR
INTERIOR OF DOOR
INTERIOR OF DOOR
3b
Locate factory installed hinge locator hole near top
end of door, and place hinge rail as shown.
Attach #10 x 1/2-in screw into pilot hole.
Actual size
1/8-in
#10 x 1/2-in
Note: The hinge rail will overlap
the top of the door by 1/8-in.
Finishing Touches
7
7a
Latch Hardware
Follow the instructions in the storm door handle kit.
7d
Expander
Drill two 3/32-in pilot holes. Do not drill through to the front of the storm door.
Secure expander.
STOP
7e
Closer
Follow the instructions in the closer kit.
7b
Expander
Slide expander onto door.
3/32-in
#6x3/8-in
Actual size
7c
Expander
Adjust the expander until the sweep lightly contacts the
threshold.
202220849-0415 NuVent Ext
-
1
-
2
LARSON 36023032 is a high-quality storm door that offers a range of features for enhanced durability, energy efficiency, and ease of use. Constructed with a sturdy aluminum frame and reinforced corners, this storm door can withstand harsh weather conditions and provides added security for your home. The included closer ensures a smooth and quiet operation, while the glass insert allows for natural light to enter your home. Installation is made simpler with the included EasyHang® feature, which enables quick and easy alignment and attachment of the door to your door frame.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
LARSON 35017031 Installation guide
-
-
LARSON 1467903157 Installation guide
-
-
-
Comfort-Bilt 38005033076 Installation guide
-
-
-
-
LARSON L91032439 Installation guide
Other documents
-
Unique Home Designs ISHV600032WHT Installation guide
-
Unique Home Designs ISHM430032NAV Installation guide
-
Unique Home Designs ISHM410032GRY Installation guide
-
Pella 5600122E05 Installation guide
-
-
Pella 6000CB05217 Installation guide
-
-
-
Andersen 10 Series Fullview Interchangeable Storm Door Installation guide
-
PCA Products A500-36808-02 Installation guide
