Cordelia Lighting 2618-327 Installation guide

2618-327

____________________________________

4 LIGHT CHAIN PENDANT

Questions, problems, missing parts? Before returning to the store,

call Cordelia Customer Service

8 a.m. – 6 p.m., EST, Monday – Friday

1-800-345-0542

4 Incandescent

60 W Bulbs or

13 W SBCFL or

equivalent LED

Bulbs

2

SAFETY INFORMATION

PLANNING THE INSTALLATION

TOOLS REQUIRED

WARNING: Disconnect the power prior to removing or installing a light fixture.

 Before starting installation of this fixture or removal of a previous fixture, disconnect

the power by turning off the circuit breaker or by removing the fuse at the fuse box.

 Consult a qualified electrician if you have any electrical questions or need to replace

the driver.

 If you have any non-electrical questions about this fixture, please contact our

Customer Service Team at 1-800-345-0542.

NOTE: Keep your receipt and these instructions for Proof of Purchase.

 Read all instructions before assembly and installation.

 Before starting installation of the fixture or removal of a previous fixture, disconnect

the power by turning off the circuit breaker or by removing the fuse at the fuse box.

 To avoid damaging this product, assemble it on a soft, non-abrasive surface such as

carpet or cardboard.

Phillips

Screwdriver

Wire

Cutter

Wire

Stripper

Flathead

Screwdriver

Ladder

Safety

Goggles

Electrical

Tape

3

CONTENTS (not shown to actual size)

Part Description Quantity

AA Cage 1

BB

Light Cluster

1

CC Canopy 1

DD Center Tube 1

EE Hooked Rod 4

FF Top Loop 1

GG Mounting Screw 2

HH Nipple 1

Part Description Quantity

II Mounting Bracket 1

JJ 5 ft. Chain 1

KK Hex Nut 2

LL Wire Nut 3

MM Threaded Ring 1

NN Chain Link Connector 2

OO Screw Collar Loop 1

KK LL

OO

MM NN

CC

AA

BB

DD

EE

II JJ

GG

HH

FF

4

INSTALLATION

 Thread two hex nuts (KK) onto the

nipple (HH) to the midpoint.

 Thread the nipple (HH) in through

the center hole of the mounting

bracket (II) approximately 1/3 of the

way. Do not tighten the hex nuts

(KK).

 Pull the supply wires out from the

outlet box.

 Attach the mounting bracket (II) to

the outlet box by feeding the

mounting screws (GG) through the

slots of the mounting bracket (II) and

tightening them into the mounting

holes of the outlet box.

 Thread the screw collar loop (OO) 8

to 9 turns onto the bottom end of the

nipple (HH).

 Tighten the bottom hex nut (KK)

against screw collar loop (OO).

 Place the canopy (CC) over the

outlet box.

 Turn the screw collar loop (OO) until

the midpoint of the outer threads of

the screw collar loop (OO) align with

the bottom surface of the canopy

(CC).

 Remove the canopy (CC) and

tighten the top hex nut (KK) against

the mounting bracket (II).

II

GG

KK

HH

OO

CC

KK

HH

5

INSTALLATION (continued)

 Screw the center tube (DD) onto the

light cluster (BB).

 Screw the top loop (FF) onto the

center tube (DD).

 Connect the top loop (FF) to each

cage (AA) corner loop using a

hooked rod (EE).

 Attach the chain (JJ) to the top loop

(FF) using a chain link connector

(NN).

 Raise the chain (JJ) and the fixture

up to the outlet box to determine the

desired length needed for

installation.

 Identify the chain link that needs to

be opened to remove the excess

chain.

 Open the chain link using two pair of

pliers.

 Remove and discard the excess

chain.

FF

EE

AA

BB

DD

Open

Chain Link

JJ

NN

FF

EE

6

INSTALLATION (continued)

 Slide the threaded ring (MM) onto

the chain (JJ) followed by the

canopy (CC).

 Attach the chain (JJ) to the screw

collar loop (OO) using a chain link

connector (NN).

 Feed the cord and fixture ground

wire into the center hole of the screw

collar loop (OO), through the nipple

(HH), and then out of the outlet box.

 Continue feeding the cord and fixture

ground wire until there is no slack

remaining.

 Cut off any excess cord and fixture

ground wire, leaving 6 in. extending

from the outlet box.

 Split and separate the fixture cord

and strip off 3/8 in. of insulation from

each wire.

AA

GG

OO

NN

II

KK

HH

GG

OO

NN

II

HH

II

HH

KK

OO

NN

JJ

CC

MM

FF

7

INSTALLATION (continued)

NOTE: If you have electrical questions

consult your local electrical code for

approved grounding methods.

 Loop the fixture ground wire around

the ground screw and leave 4 in. of

wire extending from the ground screw.

 Tighten the ground screw against the

mounting bracket (II).

 Connect the black supply wire to the

smooth fixture wire using a wire nut

(LL).

 Connect the white supply wire to the

ribbed fixture wire using a wire nut

(LL).

 Connect the fixture ground wire and

the supply ground wire together using

a wire nut (LL).

 Wrap all wire connections with

electrical tape for a more secure

connection.

 Carefully tuck all wire connections into

the outlet box.

HH

GG

OO

LL

II

KK

JJ

 Slide the canopy (CC) up the chain

(JJ), toward the outlet box, and up

against the ceiling surface.

 Slide the threaded ring (MM) up the

chain (JJ) and thread it onto the

screw collar loop (OO) to secure the

canopy (CC) flush against the ceiling

surface.

JJ

OO

MM

CC

8

INSTALLATION (continued)

NOTE: Replacement bulbs should not

exceed a 60 watt incandescent

light bulb, 13 watt SBCFL, or

equivalent LED bulb.

 Install a 60 watt bulb, 13 watt SBCFL,

or equivalent LED bulb into each

socket.

9

NOTE: Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only

a dry soft cloth to duct or wipe carefully.

EXTERIOR MAINTENANCE

 Use a dry or slightly dampened clean cloth and wipe the surface of the fixture

INTERIOR MAINTENANCE

 Disconnect power to the fixture by turning off the circuit breaker or by removing the

fuse at the fuse box.

 Use a dry or slightly dampened clean cloth to wipe the interior surface of the fixture.

 Turn on power at the circuit breaker or fuse box.

 Turn the light switch on to activate the fixture.

CARE AND CLEANING

OPERATION

TROUBLESHOOTING

Problem

Solution

The

light will not turn on.



Make sure the power supply is on.



Test or replace the switch.



Check the wiring.



Change the light bulb.

The

fuse blows or circuit breaker

trips when light is turned on.



Check the wire connections.

10

WARRANTY

WHAT IS COVERED

The manufacturer warrants this lighting fixture to be free from defects in materials and

workmanship for a period of five (5) years from date of purchase. This warranty applies

only to the original consumer purchaser and only to products used in normal use and

service. If this product is found to be defective, the manufacturer’s only obligation, and

your exclusive remedy, is the repair or replacement of the product at the manufacturer’s

discretion, provided that the product has not been damaged through misuse, abuse,

accident, modifications, alterations, neglect or mishandling.

WHAT IS NOT COVERED

This warranty shall not apply to any product that is found to have been improperly installed,

set-up, or used in any way not in accordance with the instructions supplied with the

product. This warranty shall not apply to a failure of the product as a result of an accident,

misuse, abuse, negligence, alteration, or faulty installation, or any other failure not relating

to faulty material or workmanship. This warranty shall not apply to the finish on any portion

of the product, such as surface and/or weathering, as this is considered normal wear and

tear.

The manufacturer does not warrant and specially disclaims any warranty, whether

expressed or implied, of fitness for a particular purpose, other than the warranty contained

herein. The manufacturer specifically disclaims any liability and shall not be liable for any

consequential or incidental loss or damage, including but not limited to any labor/expense

costs involved in the replacement or repair of said product.

Contact the Customer Service Team at 1-800-345-0542.

Page is loading ...

Cordelia Lighting 2618-327 Installation guide

Cordelia Lighting 2618-327 Installation guide

in other languages

Related papers

Other documents