Kichler Lighting 59003BK User manual

Type
User manual
IS-59003-US
Were here to help 866-558-5706
Hrs: M-F 9am to 5pm EST
5) (If second loop is already aached to canopy, proceed
to next step). Pass threaded pipe at end of second
loop through hole in canopy. Pass xture wire through
lockwasher [N] and thread lockwasher onto threaded
pipe protruding from inside canopy. Pass xture wire
through hole in hexnut [M] and thread hexnut onto end
of threaded pipe.
6) Aach chain link [F] to small loop at end of stem and to
loop on canopy. Close the open chain link by placing a piece
of cloth over the open link and using a pair of pliers gently
squeeze the link closed.
7) Find the appropriate threaded holes on mounng strap
[G]. Assemble mounng screws [H] into threaded holes.
8) Aach mounng strap to outlet box [I] using the strap
mounng screws [O]. The mounng strap can be
adjusted to suit posion of xture.
9) Grounding instrucons: (See Illus. a or b).
a) On xtures where mounng strap is provided with a
hole and two raised dimples, wrap ground wire from
outlet box around green ground screw, and thread
into hole.
b) On xtures where a cupped washer is
provided,aach ground wire from outlet box under
cupped washer and green ground screw, then thread
into mounng strap.
If xture is provided with ground wire, connect xture
ground wire to outlet box ground wire with wire
connector aer following the above steps. Never connect
ground wire to black or white power supply wires.
10) Make wire connecon. Reference chart below for correct
connecons and wire accordingly.
Connect Black or Red
Supply Wire to:
Connect White Supply
Wire to:
Black White
*Parallel cord (round &
smooth)
*Parallel cord (square &
ridged)
Clear, Brown, Gold or
Black without Tracer
Clear, Brown, Gold or Black
with Tracer
Insulated wire (other
than green) with copper
conductor
Insulated wire (other
than green) with silver
conductor
*Note: When parallel wire (SPT
1 & SPT 2) are used. The neutral
wire is square shaped or ridged
and the other wire will be round
in shape or smooth
(see illus.)
Neutral Wire
11) Push xture to ceiling, carefully passing mounng screws
through holes in canopy [J]. NOTE: Be certain wires do
not get pinched between canopy and ceiling.
12) Use knobs [K] and lockwashers [L] to secure canopy.
Tighten to secure.
13) Install the recommended bulbs. (Not supplied).
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
a
b
Fixture Diagram
Parts List
Cauons
CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starng and during the installaon.
WARNING:
This xture is intended for installaon in accordance
with the Naonal Electrical Code (NEC) and all local code
specicaons. If you are not familiar with code requirements,
installaon by a cered electrician is recommended.
Installaon Instrucons
[A] Coupling
[B] Stem
[C] Short
Threaded
Tubes
[D] First Loop
[E] Second Loop
[F] Chain Link
[G] Mounting
Strap
[H] Mounting
Screws
[I] Outlet Box
[J] Canopy
[K] Knobs
[L] Lockwashers
[M] Hexnut
[N] Lockwasher
[O] Strap
Mounting
Screws
1) Pass xture wire from the coupling on top of xture
through a stem [B] and threaded tubes [C] and screw
stem into coupling [A] on top of the main body.
NOTE: Thread locking compound must be applied to
all stem threads as noted with symbol (4) to prevent
accidental rotaon of xture during cleaning, relamping,
etc.
2) Pass xture wire through desired amount of stems and
screw stems together using supplied short threaded
tubes.
3) Pass xture wire from last stem through rst loop [D].
Thread rst loop onto end of last stem.
4) Pass xture wire through second loop [E] and through
hole in canopy.
Installaon Instrucons (connued)
I
G
O
J
D
B
C
M
H
F
A
N
K
L
E
  • Page 1 1
  • Page 2 2
  • Page 3 3

Kichler Lighting 59003BK User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI