Contec AI-1608VIN-USB Reference guide

Type
Reference guide

This manual is also suitable for

Reference Manual
CONTENTS
N Series for USB
Isolated Analog Input Unit (±10V Voltage Input)
AI-1608VIN-USB
Isolated Analog Input Unit (0 - 20mA Current Input)
AI-1608AIN-USB
Introduction .................................................................. 5
Safety Precautions .................................................... 13
Setup ............................................................................. 20
Installation ................................................................... 36
Software ....................................................................... 56
Function ....................................................................... 64
Appendix ...................................................................... 81
Customer Support and Inquiry ........................... 90
2
Table of Contents
Introduction ....................................................................... 5
1. Related Manuals ......................................................................................................................................................6
2. About the Product ..................................................................................................................................................7
3. Features ......................................................................................................................................................................8
1. AI-1608VIN-USB ...............................................................................................................................................8
2. AI-1608AIN-USB ...............................................................................................................................................8
3. Common ..............................................................................................................................................................8
4. Product Configuration List ............................................................................................................................... 10
5. Support Software ................................................................................................................................................. 11
6. Optional Products ................................................................................................................................................ 12
Safety Precautions ........................................................... 13
1. Safety Information ............................................................................................................................................... 14
2. Handling Precautions ......................................................................................................................................... 15
1. Regarding “CE EMC Directive Class A Notice” ................................................................................... 16
2. FCC PART15 Subpart B Class A ................................................................................................................ 17
3. EN55032Class A Notice .............................................................................................................................. 17
3. Environment ........................................................................................................................................................... 18
4. Inspection ............................................................................................................................................................... 18
5. Storage ..................................................................................................................................................................... 19
6. Disposal ................................................................................................................................................................... 19
Setup ................................................................................. 20
1. What is Setup? ...................................................................................................................................................... 21
1. Driver Software Installation ....................................................................................................................... 21
2. Driver Software Installation ............................................................................................................................. 22
1. Starting Up the Install Program ............................................................................................................... 22
3. Hardware Setting ................................................................................................................................................. 23
1. Nomenclature of Product Components ............................................................................................... 23
2. LED Indicator ................................................................................................................................................... 24
3. Setting Switches............................................................................................................................................. 24
4. USB Port ............................................................................................................................................................ 24
5. Power Supply Connector ............................................................................................................................ 25
4. Hardware installation ......................................................................................................................................... 27
1. Connecting the external power supply by self-powered .............................................................. 27
2. Connecting the Product ............................................................................................................................. 29
5. Driver Software Initialization ........................................................................................................................... 30
1. Setting the device name ............................................................................................................................ 30
6. Operation Check .................................................................................................................................................. 32
1. Check Method ................................................................................................................................................ 32
2. Using the Diagnosis Program .................................................................................................................. 32
7. Setup Troubleshooting ...................................................................................................................................... 35
3
Table of Contents
1. Examples and Solution ................................................................................................................................ 35
Installation ........................................................................ 36
1. Installing the Product ......................................................................................................................................... 37
1. Installation Conditions ................................................................................................................................ 37
2. Mounting on/Removing from a DIN Rail ............................................................................................ 40
3. Desktop Installation ..................................................................................................................................... 42
4. Mounting on the Wall ................................................................................................................................. 42
5. Installation Using the Magnet.................................................................................................................. 43
2. Connecting to an External Device ................................................................................................................. 45
1. Connecting an Interface Connector ...................................................................................................... 45
2. Connecting Cable .......................................................................................................................................... 46
3. Signal Layout on the Interface Connector .......................................................................................... 47
3. Connecting Analog Input Signal (AI-1608VIN-USB) .......................................................................... 48
1. Differential Input Connection ................................................................................................................... 48
4. Connecting Analog Input Signal (AI-1608AIN-USB) .......................................................................... 50
1. Connection Example of Current Input .................................................................................................. 50
5. Connecting Digital I/O Signals ....................................................................................................................... 53
1. Input Circuit ..................................................................................................................................................... 53
2. Example Connection with switch ............................................................................................................ 54
3. Output Circuit ................................................................................................................................................. 54
Software ............................................................................ 56
1. Analog I/O Driver for Windows...................................................................................................................... 57
1. Accessing the Help File ............................................................................................................................... 57
2. Using Sample Programs ............................................................................................................................. 57
3. Running a Sample Program ...................................................................................................................... 58
4. Distributing Developed Application ...................................................................................................... 58
5. Use of Utility Program ................................................................................................................................. 58
6. Uninstalling the Driver Software ............................................................................................................. 60
7. Returning to Initial State ............................................................................................................................ 61
2. CONTEC Device Utility ....................................................................................................................................... 62
1. Updating Firmware ....................................................................................................................................... 62
Function ............................................................................ 64
1. Analog Input Function ....................................................................................................................................... 65
1. Setting the Conversion Conditions ........................................................................................................ 66
2. Starting/Stopping Operation .................................................................................................................... 73
3. Monitoring the Status and Acquiring Data ......................................................................................... 74
4. Reset ................................................................................................................................................................... 78
2. Digital Input Function ........................................................................................................................................ 79
3. Digital Output Function .................................................................................................................................... 80
4
Table of Contents
Appendix .......................................................................... 81
1. Hardware Specification ...................................................................................................................................... 82
2. Physical Dimensions ........................................................................................................................................... 86
1. Product .............................................................................................................................................................. 86
2. Physical dimensions of the supplied AC adapter (POA201-10-2) ..................................... 86
3. Circuit Block Diagram ......................................................................................................................................... 87
4. Control Signal Timings ...................................................................................................................................... 88
1. Control Signal Timings for Analog Input ............................................................................................. 88
5. About Calibration ................................................................................................................................................ 89
Customer Support and Inquiry ...................................... 90
1. Services .................................................................................................................................................................... 91
5
Introduction
This section provides necessary information of the product
such as the outline, bundled items and manuals before
actual use.
Introduction
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
6
1. Related Manuals
The manuals related to the product are listed below.
Read them as necessary along with this document.
Must Read the Followings.
Name
Purpose
Contents
How to get
Setup Guide
Must read this after
opening the package.
This lists the product
configuration and describes
the precautions.
Included in the package
(Printed matter)
Reference Manual
(This Document)
Read this when
operating the product.
This describes the hardware
aspects such as functions
and settings.
Download Manuals
Download the manuals accordingly from the following URL.
Download
https://www.contec.com/download/
Introduction
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
7
2. About the Product
This product is an analog input unit supporting USB2.0 to provide the input function of analog signal
from USB port on the computer.
Compact design, (188.0(W)×78.0(D)×30.5(H)mm), features flexibility in installation. The product can
be set on the floor, wall, and inside the console or equipment with the DIN rail.
For AI-1608VIN-USB, 8 channels of 16-bit analog input, and digital input and output (4 channels
respectively) are equipped, and these circuits are isolated from the computer.
As the analog input supports differential input, accurate measurement can be performed even when
potential differences with the signal source occur.
The input range supports ±10V voltage input bipolar.
As for AI-1608AIN-USB, 8 channels of 16-bit analog input, and digital input and output (4 channels
respectively) are equipped, and these circuits are isolated from the computer.
As the analog input supports differential input, accurate measurement can be performed even when
potential differences with the signal source occur.
The input range supports 0-20mA current input.
Introduction
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
8
3. Features
1. AI-1608VIN-USB
8 channels of analog input (voltage input), and
4 channels of digital input and output respectively are
contained with high accuracy
Analog input (10μsec/ch, 16bit, 8ch), and digital input and output (Input: TTL level 4 channels, Output: Open-collector 4 channels) are
equipped. The analog input supports differential input and the ±10V voltage input bipolar.
2. AI-1608AIN-USB
8 channels of analog input (current input), and
4 channels of digital input and output respectively are
contained with high accuracy
Analog input (20μsec/ch, 16bit, 8ch), digital input and output (Input: TTL level 4 channels, Output: Open-collector 4 channels) are
equipped. The analog input supports differential input and the 0-20mA current input.
3. Common
Buffer memory available in FIFO format
This product contains buffer memory (8K data) which can be used in FIFO format. You can perform analog input in the background,
independent of software and the current status of the PC.
Sampling can be driven by a clock or by various triggers
Sampling can be started and stopped by software and external (timing of control signals input from external) triggers.
The sampling period can be controlled by the internal clock (high-precision timer included in the product).
Isolated from the bus by a digital isolator
This product isolates the PC from analog input as well as digital I/O by a digital isolator, which improves the noise performance.
Open collector output for digital output
The use of open collector output ensures digital outputting with TTL or 12-24 V power by the power of the external device.
Compact design not restricting installation location
(188.0(W)×78.0(D)×30.5(H))
Compact design of 188.0(W) × 78.0(D) × 30.5(H) does not require special installation location.
Introduction
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
9
Compatible to USB1.1/USB2.0
Compatible to USB1.1/USB2.0 and capable to achieve high speed transfer at High Speed (480 Mbps)
Diverse installations such as screw fastening, magnet,
DIN rail are possible
Installation on the floor / wall /ceiling is possible by screw fastening, magnet, rubber feet, etc.
In addition, DIN rail mounting mechanism is equipped as standard with the product, making it easy to install the product within the panel
or the device.
Easy-to-wire terminal connector adopted
Adoption of terminal connector (with screws) enables to achieve easy wiring.
Windows compatible driver software is provided
Using the provided driver software API-AIO(WDM) for USB makes it possible to create applications of Windows.
In addition, a Diagnostic Program to confirm the hardware operations is supplied as well.
Data logger software [C-LOGGER] (Analog input only)
compatible
Data logger software [C-LOGGER] program is compatible with our products and it displays the recorded signal data as a graph or saves
them in a file, and dynamic forwards them to the spreadsheet software program "Excel".
LabVIEW is supported by a plug-in of dedicated library
Using the dedicated library allows a user to create each application for LabVIEW.
Software-based calibration function
Calibration of analog input can be all performed by software. Apart from the adjustment information prepared before shipment,
additional adjustment information can be stored according to the use environment.
Introduction
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
10
4. Product Configuration List
The product consists of the items listed below.
Check, with the following list, that your package is complete.
If you discover damaged or missing items, contact your retailer.
Product1
Setup Guide…1
Warranty Certificate…1
Serial Number Label…1
Interface Connector…3
USB Cable (1.8m)…1
USB Cable Attachment on
the main unit’s side (For
Mini B connector side)…1
Rubber feet4
AC Adapter1
AC Cable…1
Introduction
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
11
5. Support Software
You can use CONTEC support software according to your purpose and development environment.
For more details on the supported OS, applicable languages, or to download the latest version of
software, visit the CONTEC Web site.
Name
Contents
How to get
Driver software
API-AIO(WDM) for USB
The API-AIO(WDM) is the Windows version driver
software that provides products in the form of
Win32
API functions (DLL). Various sample programs such
as Visual Basic and Visual C++, etc and diagnostic
program useful for checking operation is provided.
Download from the
CONTEC website
Data Logger Software
C-LOGGER
C-LOGGER is a data logger software program
compatible with our analog I/O products. This
program enables the recorded signal data to be
displayed as a graph, zoom-observed, saved in a file,
and dynamic forwarded to the spreadsheet software
program "Excel".
It eliminates the need for tedious programming.
Download from the
CONTEC website
LabVIEW VI Library for Data
Acquisition
DAQfast for LabVIEW
This is a data collection library to use our devices in
the LabVIEW by National Instruments.
With Polymorphic VI, our design enables a LabVIEW
user to operate seamlessly.
Our aim is for the customers to perform easily,
promptly what they wish to do.
Download from the
CONTEC website
Download the files from the following URL.
Download
https://www.contec.com/download/
Introduction
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
12
6. Optional Products
Optional product items are as follows:
Use these items with the main product as necessary.
Product Name
Model type
Description
AC adapter
POA201-10-2 *1
Input: 90 - 264VAC, Output: 12VDC 1.0A
DIN rail fitting power supply
CPS-PWD-90AW24-01 *2
90W (Input: 100-240VDC, Output: 12VDC 3.8A)
CPS-PWD-30AW24-01 *2
30W (Input: 100-240VDC, Output: 12VDC 1.3A)
CPS-PWD-15AW12-01 *2
15W (Input: 100-240VDC, Output: 12VDC 1.3A)
Magnet
CPS-MAG01-4
Magnet (Four Piece Set)
*1 The operating ambient temperature is 0 to 40 °C. It is the same adapter included in this package.
*2 The operating ambient temperature is -20 to 70 °C.
Visit the CONTEC website for the latest optional products.
Website
https://www.contec.com/
13
Safety Precautions
Understand the following definitions and precautions to
use the product safely.
Never fail to read them before using the product.
Safety Precautions
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
14
1. Safety Information
This document provides safety information using the following symbols to prevent accidents
resulting in injury or death and the destruction of equipment and resources.
Understand the meanings of these labels to operate the equipment safely.
DANGER
DANGER
indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION
indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury or in property damage.
Safety Precautions
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
15
2. Handling Precautions
DANGER
Do not use the product in locations exposed to a flammable or corrosive gas. It may cause
explosion, fire, electrical shock, or malfunction.
Do not place the product in an unstable location or use incomplete mountings. Otherwise, it
may cause the device to fall.
CAUTION
Do not strike or bend this product.
Otherwise, this product may malfunction, overheat, cause a failure or breakage.
Do not touch this product's metal plated units (USB connector) with your hands.
Otherwise, the product may malfunction, overheat, or cause a failure. When you touch the
product, wipe it clean with industrial alcohol.
Do not close the ventilation hole(s) of this product by, for example, placing an object.
This may cause overheating, malfunction, and/or failure of the product.
Do not touch the external connector when the power is on. Otherwise this product may
malfunction, overheat, or cause a failure due to static electricity.
Do not set or remove the power supply connector and interface connector when the power is
on. This may cause a failure.
When the product is self-powered, do not plug or unplug the 12-24VDC power with the
product while the 12-24VDC is outputting the voltage. This may cause a failure.
Do not operate switches when the power is on. This may cause a failure.
When connecting multiple products, set one product at a time. Complete the setup before
starting to connect the next product.
If you use this product in a noisy environment, connect the FG pin of the product to the
ground (earth) to stabilize the operation.
The specifications of the product are subject to change without notice for enhancement and
quality improvement. Even when using the product continuously, be sure to read the manual
in the CONTEC's website and understand the contents.
Do not modify the product. CONTEC will bear no responsibility for any problems, etc.,
resulting from modifying the product.
Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever
(Including damages for loss of business profits) arising out of the use or inability to use this
CONTEC product or the information contained herein.
Safety Precautions
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
16
1. Regarding CE EMC Directive Class A Notice
The ferrite core must be installed on the AC adapter so that this product may suit the above-
mentioned standard.
See below for the type of the ferrite core. (Equivalent product can also be used).
Name
Maker
Turn
Quantity
Installation Site
E04SR241336A
SEIWA
2
1
On DC cable and FG cable at the product side
Image diagram
Safety Precautions
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
17
2. FCC PART15 Subpart B Class A
NOTE
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
3. EN55032Class A Notice
Warning:
Operation of this equipment in a residential environment could cause radio interference.
Safety Precautions
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
18
3. Environment
Use this product in the following environment. If used in an unauthorized environment, this product may overheat,
malfunction, or cause a failure.
Operating temperature
-20 - 60ºC
Humidity
10 - 90%RH (No condensation)
Corrosive gases
None
Floating dust particles
Not to be excessive
4. Inspection
Inspect the product periodically as follows to use it safely.
CAUTION
Check that the ventilation slit has no obstruction and has no dust or foreign matter adhering.
Moreover, if there is the slit on the case side, please confirm it to the slit similarly.
Safety Precautions
AI-1608VIN-USB / AI-1608AIN-USB Reference Manual
19
5. Storage
When storing this product, keep it in its original packing form.
Put this product in the storage bag.
Wrap it in the packing material, and then put it in the box.
Store the package at room temperature at a place free from direct sunlight, moisture, shock,
vibration, magnetism, and static electricity.
6. Disposal
When disposing of the product, follow the disposal procedures stipulated under the relevant laws
and municipal ordinances.
20
Setup
This section explains how to set up this product.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93

Contec AI-1608VIN-USB Reference guide

Type
Reference guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI