3
All Weather Flashing Tape
8067
Application Guide January, 2010
Installation Guide
for Windows with
Mounting Flanges
• These guidelines outline how to use 3M™ All Weather Flashing Tape 8067 to flash
a flanged window installed in a wall assembly consisting of housewrap over an
exterior sheathing on a wood frame wall.
• The following installation information is intended to represent a “best practices”
approach and is not intended to address all possible construction scenarios or all
window manufacturers’ installation instructions. Some of the information described
below is similar to that described in ASTM E 2112, Method A1.
• Follow the window manufacturer’s instructions as installation methods may be
a requirement of the window manufacturer’s warranty.
Install the weather
resistive barrier
1. Install the weather resistive barrier (WRB) per the manufacturer’s instruction in
an over-lapping water shedding fashion over the entire wall. Make a modified “I”
cut through the building wrap as shown in Fig. 1A.
Figure 1A: Install and cut the WRB
2
nd
& 3
rd
cuts
1
st
cut
4
th
cut
5
th
& 6
th
cuts
6"-9" long
WRB
Application Guide
3M
™
All Weather Flashing Tape
8067
- 2 -
Fold and fasten
the WRB
2. Fold and fasten the WRB: Fold the header flap up above the window exposing
the sheathing and temporarily tape in place. Fold the side flaps of the WRB into the
opening and staple to inside wall. Fold the bottom flap in and trim the WRB on the
sill to allow the flashing tape to adhere to the wood as shown in Fig. 2A.
Figure 2A: Fold and fasten the WRB
Tape in
place
temporarily
Header flap
folded up
and taped
WRB folded
in, trimmed
and stapled
Exposed sheathing
WRB folded in
and stapled
Wood
- 3 -
Application Guide
3M
™
All Weather Flashing Tape
8067
Apply sill
flashing tape
3. Apply sill flashing tape:
NOTE: There are other methods for flashing the sill that require additional materials
which are not included in this guide. However, it is good practice to create a slope on the
sill that directs water down to the outside of the building. In this case, a sloped sill may
be installed directly over the WRB before applying the sill flashing tape.
Follow this procedure when applying 3M™ All Weather Flashing Tape 8067:
Peel back a few inches of one side of the split paper release liner to position the tape.
Remove the liner while applying firm pressure to the flashing tape surface as it comes
into contact with the building surface. Repeat this procedure with the remaining side of
the paper release liner and tape. Using a roller (rubber, wood or steel “J” roller) apply
sufficient pressure along the entire tape surface to ensure a continuous seal and to
eliminate trapping air beneath the tape.
A. Cut a piece of 3M™ All Weather Flashing Tape 8067 a length equivalent to the width
of the rough opening plus 2 times the width of the flashing tape. Position and apply
the flashing tape on the face of the wall so that the top edge of the flashing tape
extends one inch above the top edge of the sill rough opening as shown in Fig. 3A1
and 3A2 as 1
st
sill flashing tape.
Figure 3A1: 1
st
sill flashing tape
The top edge of the flashing
tape is one inch above the
top edge of the sill rough
opening. See Figure 3A2
below.
3A1. 1
st
sill flashing tape is
the width of the rough
opening plus 2x the width of
the flashing tape. The tape
extends beyond the rough
opening approximately 1x the
width of the flashing tape on
each side.
Exposed sheathing
Figure 3A2: 1
st
sill flashing tape
1 in.
Extend flashing tape 1" above the sill, cut along
the right and left corner, fold back onto the sill.
Extend 1 width of flashing tape
on each side of the opening.
- 4 -
Application Guide
3M
™
All Weather Flashing Tape
8067
Apply sill
flashing tape
(continued)
B. Cut another piece of 3M™ All Weather Flashing Tape 8067 12" longer than the
opening width. This is in order for the tape to extend 6" up each side of the
opening. Apply the flashing tape to the inside of the sill as shown in Fig. 3B, so it
overhangs 1" into the exterior wall and over the WRB and tape applied in step 1.
Cut the 1" overhang at each corner, as shown in Fig 3B. Fold tape to the exterior
over the WRB or tape and press firmly to obtain good contact and adhesion. This
is the 2
nd
sill flashing tape.
C. Cut another piece of 3M™ All Weather Flashing Tape 8067 12" longer than the
opening width. Apply the tape to the inside of the sill overlapping the 2
nd
sill tape
by at least 1" as shown in Fig. 3C. The tape should NOT extend beyond the
interior face of the framing, and does not need to extend all the way to the interior
of the window opening. This is the 3
rd
sill flashing tape.
Figure 3B: 2
nd
sill flashing tape
1 in.
1 in.
6 in.
2
nd
sill flashing tape extends 1" over the wall
and is applied over the 1
st
sill flashing tape.
Flashing tape extends 6"
up each side of the sill.
3
rd
sill flashing tape
extends at least 1" over
the 2
nd
sill flashing tape.
1 in.
Figure 3C: 3
rd
sill flashing tape
- 5 -
Application Guide
3M
™
All Weather Flashing Tape
8067
Install the
window
4. Install the window, plumb, level and square, in accordance with the window
manufacturer’s instructions. Typically, this requires that a bead of sealant be applied to
the back side of the window flange prior to installing the window.
Note: Do not seal the bottom flange of the window. Attach the window using fasteners
specified by the window manufacturer and spaced as directed.
Install the jamb
flashing tape
5. Install the jamb flashing tape: Cut two pieces of 3M™ All Weather Flashing Tape
8067 a length equivalent to the length of the frame height of the window plus 2 times
the width of the flashing tape. The flashing tape should extend beyond both the top and
bottom of the window frame by a length equal to the width of the tape. Be sure that the
jamb flashing tape overlaps the sill flashing tape. Apply one piece of flashing tape to
each side of the window over the nailing fin and onto the WRB as shown in Fig. 5.
Figure 5: Install the jamb flashing tape
Apply one piece of flashing tape to each side of the
window over the nailing fin and onto the WRB.
Cut the flashing tape the frame
height of the window plus 2 times
the width of the flashing tape.
The flashing tape should extend
beyond both the tape and bottom of
the window by a length equivalent
to the width of the tape and
overlaps the sill flashing tape.
- 6 -
Application Guide
3M
™
All Weather Flashing Tape
8067
Install the header
flashing tape
6. Install the header flashing tape: Cut a piece of 3M™ All Weather Flashing Tape
8067 a length equivalent to the frame width of the window plus 2 times the width of
the flashing tape plus 2 inches. The header flashing tape should overlap and extend
beyond the jamb flashing tapes by at least 1 inch on each side as shown in Fig. 6.
Apply the flashing tape to the top of the window over the nailing fin and directly onto
the sheathing.
Fold down
the header
flap of WRB
7. Fold down the header flap of WRB: Fold down the WRB header flap so that it
overlaps the header flashing tape as shown in Fig. 7. Trim the WRB header flap so that
it does not touch the top of the window frame. Tape the diagonal cuts in the WRB with
3M™ All Weather Flashing Tape 8067.
The flashing tape should overlap and extend
beyond the jamb flashing by at least 1".
Cut the flashing tape the frame width
of the window plus 2 times the width
of the flashing tape plus 2 inches.
Apply the flashing tape to the top of
the window over the nailing fin and
directly onto the sheathing.
Figure 6: Install the header flashing tape
Figure 7: Fold down the header flap of WRB
Fold down the WRB
header flap so it
overlaps the header
flashing tape.
Tape the diagonal
cuts in the WRB
with flashing tape.
- 7 -
Application Guide
All Weather Flashing Tape
8067
The technical information, recommendations and other statements contained in this document are
based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such
information is not guaranteed.
Technical Information
Unless an additional warranty is specifically stated on the applicable 3M product packaging or product
literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time
3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY
OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE.
If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M’s
option, replacement of the 3M product or refund of the purchase price.
Warranty,
Limited Remedy,
and Disclaimer
Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product,
whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted,
including warranty, contract, negligence or strict liability.
Limitation of Liability
This Industrial Adhesives and Tapes Division product was manufactured under a 3M quality system registered to ISO 9001: 2000 standards.
ISO 9001: 2000
Many factors beyond 3M’s control and uniquely within user’s knowledge and control can affect the use
and performance of a 3M product in a particular application. Given the variety of factors that can affect
the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and
determining whether it is fit for a particular purpose and suitable for user’s method of application.
Product Use
3M is a trademark of 3M Company.
Printed in U.S.A.
©3M 2010 (1/10)
Recycled Paper
40% pre-consumer
10% post-consumer
3
Industrial Adhesives and Tapes Division
3M Center, Building 225-3S-06
St. Paul, MN 55144-1000
800-362-3550 • 877-369-2923 (Fax)
www.3M.com/industrial
-
1
-
2
-
3
-
4
-
5
-
6
-
7
3M 8067-475 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
3M Fire Barrier Tuck-In Wrap Strips User guide
-
-
-
-
-
-
-
-
-
Other documents
-
Gibraltar Building Products 10112-1R Operating instructions
-
TAFCO WINDOWS VPS3636 Installation guide
-
-
-
-
Insultex IHW-100 Installation guide
-
HydroGap HGAPS Installation guide
-
DuPont HDXXTYVK6 Installation guide
-
Typar 3234A-911 Installation guide
-
Ply Gem CLASSIC SH Installation guide
