Havis-Shields C-TM-IMP User manual

Brand: Havis-Shields

Model: C-TM-IMP

Type: User manual

This manual is also suitable for

2000-2005 Chevrolet Impala Trak-Mount Kit C-TM-IMP

Havis-Shields 2000-2005 Chevrolet Impala Trak-Mount Kit C-TM-IMP

This kit provides a secure and convenient mounting solution for equipment in your 2000-2005 Chevrolet Impala.

Havis-Shields 2000-2005 Chevrolet Impala Trak-Mount Kit C-TM-IMP

This kit provides a secure and convenient mounting solution for equipment in your 2000-2005 Chevrolet Impala.

TRAK-MOUNT ASSEMBLY

(Image Upside down)

INSTALL INSTRUCTIONS C-TM-IMP

2000-2005 CHEVROLET IMPALA TRAK-MOUNT KIT

TOOLS REQUIRED:

Ratcheting Wrench

Metric Socket Set

Torx Bit Set

Standard Socket Set

Tape Measure

HARDWARE:

QTY DESCRIPTION PART#

8 ¼” x ¾” hex head bolt GSM33001

8 ¼” Serrated nut GSM30023

6 ¼” x 1” Hex head lag bolts GSM33060

1 32” Trak mount CM93055-9

SUB ASSEMBLY:

1. MOUNT TRAK TO HUMP BRACKETS.

• Determine location that Trak will land on transmission hump for the specific

application.

• With Trak in necessary location, measure Front and Rear Hump Brackets in relation

to Trak.

• Bolt Trak to Hump Brackets, using measurements taken in previous step

Note: There are 2 different sides to the Trak Plate. It is recommended to mount Hump brackets

to side of Trak Plate that has ¼” hardware slots closer together, to better accept equipment,

(consoles, control heads, etc)

• Slide (6) ¼-20 x ¾” Hex Head Bolts into ¼” Hardware Slots.

• With bolts in Trak, position Hump brackets.

• There is a left and right side to the Rear Hump Brackets. Top of brackets will be

parallel to the transmission hump.

• Attach ¼” serrated nuts and tighten.

Front Hump Bracket C-B17

Rear Hump Bracket C-B27

Trak

¼” Hardware Slots

C-TM-IMP-INST-2-07

INSTALLATION:

1. REMOVE SEATS:

• Remove rear seat base torx bolts.

• Slide seat to rear most position.

• Seats do not have to come out of vehicle, they will just need to be tilted out of way to

place Trak-Mount assembly. Be careful of wire plugs if vehicle has power seats.

2. MOUNT ASSEMBLED TRAK-MOUNT:

• Place Trak-Mount assembly so front bracket sets squarely on floor beam straddling

seat bolts – lag bolt to the floor beam. The rear hump brackets are place on floor

between floor of vehicle and seat base and can be mounted using the rear seat bolts.

• Re-mount seats over Trak-Mount assembly and tighten all hardware.

• Mount equipment (consoles, control heads, etc), prior to plastic end caps, for access

to hardware slots.

Rear Hump Bracket

(Driver Side)

Rear Hump Bracket

(Pass. Side)

Front Hump Bracket

Trak

Havis-Shields C-TM-IMP User manual

Brand: Havis-Shields

Model: C-TM-IMP

Type: User manual

This manual is also suitable for

2000-2005 Chevrolet Impala Trak-Mount Kit C-TM-IMP

Havis-Shields 2000-2005 Chevrolet Impala Trak-Mount Kit C-TM-IMP

This kit provides a secure and convenient mounting solution for equipment in your 2000-2005 Chevrolet Impala.

Download PDF

report

Havis-Shields C-TM-IMP User manual

This manual is also suitable for

Havis-Shields C-TM-IMP User manual

Related papers

Other documents