Page is loading ...
Supreme M3 Assembly
Table of Contents
1. Assembling the Motor Unit ............................................................................................................... 5
2. Assembling the Driving System and Side Cover ................................................................................ 6
3. Assembling the Driving System and Side Cover on the other side of the robot ................................. 9
4. Assembling the floating cable ........................................................................................................ 10
5. Positioning the Float ...................................................................................................................... 12
6. Assembling the Outer Casing ......................................................................................................... 13
7. Assembling the Impeller Cover ...................................................................................................... 14
8. Assembling the Brushes ................................................................................................................. 15
Supreme M3 Assembly
Supreme M3 Assembly
Supreme M3 Assembly
Supreme M3 Assembly
1. Assembling the Motor Unit
Step 1.1
Assemble the
cover cork into
the Pulley's
place.
Step 1.2
Place the motor
unit in its place.
Note:
The drive
motor side
should be in
the opposite
side of the
cover cork.
Supreme M3 Assembly
2. Assembling the Driving System and Side
Cover
Step 1.3
Secure the
motor unit to
the frame with
4X KA50X30.
Step 2.1
Place the guide
wheels on the
side of the
motor shaft.
1.3
Supreme M3 Assembly
Step 2.2
Insert the
hexagon
adaptor into
the Pulley.
Step 2.3
Place the
track on the
Pulley.
Step 2.4
Put the Pulley
And the track
in their
places.
Note:
Make sure
the adaptor
is on the
motor
shaft.
Note:
There are two
types of
tracks – short
and long. Use
the longer
track in the
Pulley side.
Supreme M3 Assembly
Step 2.5
Put the side
panel with the
wheel on the
drive motor
side.
Step 2.6
Press on the
bottom of the
side panel to
fit the clips
into their
places.
Step 2.7
Secure the side
panel in place
with 4
KA40X20
screws.
Note:
The side
panel with
the wheel
should be in
the drive
motor side
Supreme M3 Assembly
3. Assembling the Driving System and Side
Cover on the other side of the robot
Step 3.1
Put the
shorter track
on the other
side of the
robot as
shown.
Step 3.2
Put the side
panel with the
fins into its
place.
Step 3.3
Secure the
side panel in
place with 4
KA40X20
screws.
Supreme M3 Assembly
4. Assembling the floating cable
Step 4.1
Pass the
cable through
the outer
casing as
shown.
Step 4.2
Insert the
floating cable
to the motor
unit.
Step 4.3
Press the
seal firmly to
the terminal.
Supreme M3 Assembly
Tip!
Use the cable
key to close
the screw.
Step 4.4
Tighten the
plastic screw
properly with
the special
torque key-
Step 4.5
Position the
cable on the
motor unit
and secure
the cable
holder with
4X KA50X12.
Step 4.6
The cable
position on
the motor
unit + cable
holder
Supreme M3 Assembly
5. Positioning the Float
Step 5.1
Place the
float on the
motor unit,
on the drive
motor side as
shown.
Note:
PVC models
have two
floats on the
motor unit.
Supreme M3 Assembly
6. Assembling the Outer Casing
Step 6.1
Place the
outer casing
on the frame.
Step 6.2
Make sure
the casing
seats well on
the side
panel slots.
Step 6.3
Secure the
outer casing
to the frame
with 4X KA
50x25.
Supreme M3 Assembly
7. Assembling the Impeller Cover
Step 7.1
Place the
cable spring
in its place
on the outer
casing before
closing the
impeller
cover.
Step 7.2
Position the
impeller
cover
diagonally on
the outer
casing as
shown.
Step 7.3
Secure the
impeller
cover with a
KA50X12
screw.
Supreme M3 Assembly
8. Assembling the Brushes
Step 8.1
Place one
brush in
place.
Step 8.2
.
Step 8.3
Place the
second brush
in its place
by pushing it
strongly
away from
you.
Note:
Using a
screwdriver
makes it
easier to
insert the
brush in
place.
Supreme M3 Disassembly Instructions
Table of Contents
1. Dismantling the Impeller Cover ....................................................................................................... 2
2. Dismantling the Outer Casing ........................................................................................................... 3
3. Dismantling the Cable ...................................................................................................................... 4
4. Dismantling the Motor Unit .............................................................................................................. 5
5. Dismantling the Side Panels ............................................................................................................. 6
6. Dismantling the Drive System .......................................................................................................... 7
Supreme M3 Disassembly Instructions
1. Dismantling the Impeller Cover
Step 1.1
Unscrew the 3
screws holding
the cover in
place.
Step 1.2
Lift the cover
off.
Tip:
Use needle-nosed
pliers to remove
the cover.
Supreme M3 Disassembly Instructions
2. Dismantling the Outer Casing
Step 2.1
Unscrew the 4
screws holding
the cover in
place.
Step 2.2
Hold the outer
casing on both
sides. Pull it
up to remove
it.
2.2
Supreme M3 Disassembly Instructions
3. Dismantling the Cable
Step 3.1
Dismantle the
2 screws on
the cable
holder.
Step 3.2
Remove the
float from the
motor unit.
Step 3.3
Release the
cable from the
motor unit,
using the
Terminal Key.
Step 3.4
Unplug the
cable.
Note:
PVC models
have two
floats on
the motor
unit.
Supreme M3 Disassembly Instructions
4. Dismantling the Motor Unit
Step 4.1
Unscrew the
4 screws
holding the
motor unit in
place.
Step 4.2
Remove the
motor unit.
Step 4.3
Remove the
hexagon
adaptor.
/
