13
EN
display. The Child Lock does not allow any
change in the programmes and the selected
temperature, speed and auxiliary functions.
C
Even if another programme is selected with the
ProgrammeSelectionknobwhiletheChildLock
is active, previously selected programme will
continue running.
To activate the Child Lock:
Press and hold 1
st
and 2
nd
AuxiliaryFunctionbuttons
for 3 seconds. The lights on the 1
st
and 2
nd
Auxiliary
Functionbuttonswillflash,and"C03","C02","C01"
will appear on the display respectively while you keep
thebuttonspressedfor3seconds.Then,"Con"
will appear on the display indicating that the Child
Lockisactivated.Ifyoupressanybuttonorturnthe
ProgrammeSelectionknobwhentheChildLockis
active, same phrase will appear on the display. The
lightsonthe1stand2ndauxiliaryfunctionbuttons
thatareusedtodeactivatetheChildLockwillblink
3 times.
To deactivate the Child Lock:
Press and hold 1
st
and 2
nd
auxiliaryfunctionbuttons
for 3 seconds while any programme is running. The
lights on the 1
st
and 2
nd
AuxiliaryFunctionbuttons
will flash, and "C03", "C02", "C01" will appear on
thedisplayrespectivelywhileyoukeepthebuttons
pressedfor3seconds.Then,"COFF"willappear
on the display indicating that the Child Lock is
deactivated.
C
Inadditiontothemethodabove,todeactivate
the Child Lock, switch the Programme Selection
knobtoOn/Offpositionwhennoprogrammeis
running, and select another programme.
C
Child Lock is not deactivated after power failures
or when the machine is unplugged.
C
IfyouswitchoffthemachinebypressingtheOn
/OffbuttonwhentheChildLockisactiveand
the machine is running, then the child lock will
bedeactivated.
Progress of programme
Progressofarunningprogrammecanbefollowed
fromtheProgrammeFollow-upindicator.Atthe
beginningofeveryprogrammestep,therelevant
indicator light will turn on and light of the completed
step will turn off.
You can change the auxiliary functions, speed
and temperature settings without stopping the
programme flow while the programme is running.
To do this, the change you are going to make must
beinastepaftertherunningprogrammestep.Ifthe
changeisnotcompatible,relevantlightswillflashfor
3 times.
C
Ifthemachinedoesnotpasstothespinning
step,RinseHoldfunctionmightbeactiveorthe
automaticunbalancedloaddetectionsystem
mightbeactivatedduetotheunbalanced
distributionofthelaundryinthemachine.
Loading door lock
There is a locking system on the loading door of the
machine that prevents opening of the door in cases
whenthewaterlevelisunsuitable.
Loading door light will start flashing when the
machine is switched to Pause mode. Machine
checksthelevelofthewaterinside.Ifthelevelis
suitable,LoadingDoorlightilluminatessteadilywithin
1-2minutesandtheloadingdoorcanbeopened.
Ifthelevelisunsuitable,LoadingDoorlightturnsoff
andtheloadingdoorcannotbeopened.Ifyouare
obligedtoopentheLoadingDoorwhiletheLoading
Doorlightisoff,youhavetocancelthecurrent
programme; see "Canceling the programme".
Changing the selections after
programme has started
Switching the machine to pause mode
PresstheStart/Pausebuttontoswitchthemachine
to pause mode while a programme is running.
The light of the step which the machine is in starts
flashingintheProgrammeFollow-upindicatorto
showthatthemachinehasbeenswitchedtothe
pause mode.
Also,whentheloadingdoorisreadytobeopened,
LoadingDoorlightwillalsoilluminatecontinuouslyin
addition to the programme step light.
Changing the speed and temperature settings
for auxiliary functions
Dependingonthesteptheprogrammehasreached,
you may cancel or activate the auxiliary functions;
see, "Auxiliary function selection".
You may also change the speed and temperature
settings; see, "Spin speed selection" and
"Temperature selection".
C
Ifnochangeisallowed,therelevantlightwill
flash for 3 times.
Adding or taking out laundry
PresstheStart/Pausebuttontoswitchthemachine
topausemode.Theprogrammefollow-uplightof
the relevant step during which the machine was
switched into the pause mode will flash. Wait until
theLoadingDoorcanbeopened.OpentheLoading
Doorandaddortakeoutthelaundry.Closethe
LoadingDoor.Makechangesinauxiliaryfunctions,
temperature and speed settings if necessary. Press
Start/Pausebuttontostartthemachine.
C
The loading door will not open if the water
temperature in the machine is high or the water
levelisabovethedooropening.
Canceling the programme
To cancel the programme, turn the Programme
Selectionknobtoselectanotherprogramme.
Previousprogrammewillbecanceled.End/
Cancel light will flash continuously to notify that the
programmehasbeencanceled.
Pumpfunctionisactivatedfor1-2minutesregardless
of the programme step, and whether there is water
in the machine or not. After this period, your machine
willbereadytostartwiththefirststepofthenew
programme.
C
Dependingonthestepwheretheprogramme
was canceled in, you may have to put detergent
and softener again for the programme you have
selected anew.
C
Ifyouwanttoopentheloadingdoorafteryou
havecancelledtheprogrammebutitisnot
possibletoopentheloadingdoorsincethe
waterlevelinthemachineisabovetheloading
door opening, then turn the Programme