12
EN
active, previously selected programme will continue
running.
ToactivatetheChildLock:
Pressandhold1
st
and 2
nd
Auxiliary Function buttons for
3seconds.Thelightsonthe1
st
and 2
nd
Auxiliary Function
buttonswillflash,and"C03","C02","C01"willappearonthe
display respectively while you keep the buttons pressed for
3 seconds. Then, "Con" will appear on the display indicating
thattheChildLockisactivated.Ifyoupressanybuttonorturn
theProgrammeSelectionknobwhentheChildLockisactive,
samephrasewillappearonthedisplay.Thelightsonthe1st
and 2nd auxiliary function buttons that are used to deactivate
theChildLockwillblink3times.
TodeactivatetheChildLock:
Pressandhold1
st
and 2
nd
auxiliary function buttons for 3
seconds while any programme is running. The lights on the
1
st
and 2
nd
AuxiliaryFunctionbuttonswillflash,and"C03",
"C02","C01"willappearonthedisplayrespectivelywhile
you keep the buttons pressed for 3 seconds. Then, "COFF"
willappearonthedisplayindicatingthattheChildLockis
deactivated.
C
Inadditiontothemethodabove,todeactivatetheChild
Lock,switchtheProgrammeSelectionknobtoOn/
Off position when no programme is running, and select
another programme.
C
ChildLockisnotdeactivatedafterpowerfailuresor
when the machine is unplugged.
C
IfyouswitchoffthemachinebypressingtheOn/Off
buttonwhentheChildLockisactiveandthemachineis
running, then the child lock will be deactivated.
Progress of programme
Progress of a running programme can be followed from the
ProgrammeFollow-upindicator.Atthebeginningofevery
programme step, the relevant indicator light will turn on and
light of the completed step will turn off.
You can change the auxiliary functions, speed and
temperature settings without stopping the programme flow
while the programme is running. To do this, the change
you are going to make must be in a step after the running
programmestep.Ifthechangeisnotcompatible,relevant
lights will flash for 3 times.
C
Ifthemachinedoesnotpasstothespinningstep,
RinseHoldfunctionmightbeactiveortheautomatic
unbalanced load detection system might be activated
due to the unbalanced distribution of the laundry in the
machine.
Loading door lock
There is a locking system on the loading door of the machine
that prevents opening of the door in cases when the water
level is unsuitable.
Loadingdoorlightwillstartflashingwhenthemachine
is switched to Pause mode. Machine checks the level of
thewaterinside.Ifthelevelissuitable,LoadingDoorlight
illuminatessteadilywithin1-2minutesandtheloadingdoor
can be opened.
Ifthelevelisunsuitable,LoadingDoorlightturnsoffandthe
loadingdoorcannotbeopened.Ifyouareobligedtoopen
theLoadingDoorwhiletheLoadingDoorlightisoff,you
havetocancelthecurrentprogramme;see"Cancelingthe
programme".
Changing the selections after
programme has started
Switching the machine to pause mode
PresstheStart/Pausebuttontoswitchthemachinetopause
mode while a programme is running. The light of the step
which the machine is in starts flashing in the Programme
Follow-upindicatortoshowthatthemachinehasbeen
switched to the pause mode.
Also,whentheloadingdoorisreadytobeopened,Loading
Doorlightwillalsoilluminatecontinuouslyinadditiontothe
programme step light.
Changing the speed and temperature settings for
auxiliary functions
Dependingonthesteptheprogrammehasreached,you
maycanceloractivatetheauxiliaryfunctions;see,"Auxiliary
function selection".
Youmayalsochangethespeedandtemperaturesettings;
see, "Spin speed selection" and "Temperature selection".
C
Ifnochangeisallowed,therelevantlightwillflashfor3
times.
Adding or taking out laundry
PresstheStart/Pausebuttontoswitchthemachineto
pausemode.Theprogrammefollow-uplightoftherelevant
step during which the machine was switched into the pause
modewillflash.WaituntiltheLoadingDoorcanbeopened.
OpentheLoadingDoorandaddortakeoutthelaundry.
ClosetheLoadingDoor.Makechangesinauxiliaryfunctions,
temperatureandspeedsettingsifnecessary.PressStart/
Pause button to start the machine.
C
The loading door will not open if the water temperature
in the machine is high or the water level is above the
door opening.
Canceling the programme
To cancel the programme, turn the Programme Selection
knob to select another programme. Previous programme will
becanceled.End/Cancellightwillflashcontinuouslytonotify
that the programme has been canceled.
Pumpfunctionisactivatedfor1-2minutesregardlessofthe
programme step, and whether there is water in the machine
or not. After this period, your machine will be ready to start
with the first step of the new programme.
C
Dependingonthestepwheretheprogrammewas
canceled in, you may have to put detergent and softener
again for the programme you have selected anew.
C
Ifyouwanttoopentheloadingdoorafteryouhave
cancelled the programme but it is not possible to open
the loading door since the water level in the machine
is above the loading door opening, then turn the
Programme Selection knob to Pump+Spin programme
and discharge the water in the machine.
End of programme
“End” appears on the display at the end of the programme.
Wait until the loading door light illuminates steadily. Press On
/Offbuttontoswitchoffthemachine.Takeoutyourlaundry
and close the loading door. Your machine is ready for the next
washing cycle.