DeWalt DW223-220 User manual

Brand: DeWalt

Model: DW223-220

Category: Power tools

Type: User manual

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

DW217/DW221/DW222/DW223/DW223G/DW223-220/DW226/DW231/DW235G

DW235-220/DW236/DW238/DW239/DW245/DW246/DW248/DW249

Drills

Perceuses

Taladros

Questions? See us on the World Wide Web at www.dewalt.com

wire grounded power cord and grounded power supply system.

Applicable only to Class II (double insulated) tools. The DW217,

DW221, DW222, DW223, DW226, DW231, DW235, DW236,

DW245 and DW246 units have a polarized plug. The DW217,

DW221, DW222, DW223, DW223-220, DW226, DW231, DW235,

DW235-220, DW236, DW238, DW239, DW245, DW246, DW248

and DW249 units are double insulated. The DW223-220, and

DW235-220 units are rated at 230 volts and they are fitted with the

220 volt style plug which is not polarized.

• Avoid body contact with grounded surfaces such as pipes,

radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is grounded.

• Don’t expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

• Do not abuse the cord. Never use the cord to carry the tools or

pull the plug from an outlet. Keep cord away from heat, oil, sharp

edges or moving parts. Replace damaged cords immediately.

Damaged cords increase the risk of electric shock.

• When operating a power tool outside, use an outdoor exten-

sion cord marked “W-A” or “W.” These cords are rated for out-

door use and reduce the risk of electric shock. When using an

extension cord, be sure to use one heavy enough to carry the cur-

rent your product will draw. An undersized cord will cause a drop in

line voltage resulting in loss of power and overheating. The follow-

ing table shows the correct size to use depending on cord length

and nameplate ampere rating. If in doubt, use the next heavier

gage. The smaller the gage number, the heavier the cord.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

240V 0-50 51-100 101-200 201-300

Ampere Rating

More Not more AWG

Than Than

0-6 18161614

6 - 10 18 16 14 12

English

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

EWALT TOOL, CALL US TOLL FREE AT:

1-800-4-DEWALT (1-800-433-9258)

General Safety Rules

WARNING! Read and understand all instructions.

Failure to follow all instructions listed below may result in

electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

WORK AREA

• Keep your work area clean and well lit. Cluttered benches and

dark areas invite accidents.

• Do not operate power tools in explosive atmospheres, such

as in the presence of flammable liquids, gases, or dust. Power

tools create sparks which may ignite the dust or fumes.

• Keep bystanders, children, and visitors away while operating

a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

• Grounded tools must be plugged into an outlet properly

installed and grounded in accordance with all codes and ordi-

nances. Never remove the grounding prong or modify the

plug in any way. Do not use any adaptor plugs. Check with a

qualified electrician if you are in doubt as to whether the out-

let is properly grounded. If the tools should electrically malfunc-

tion or break down, grounding provides a low resistance path to

carry electricity away from the user. The DW223G and the

DW235G units are grounded. Applicable only to Class I

(grounded) tools.

• Double insulated tools are equipped with a polarized plug

(one blade is wider than the other.) This plug will fit in a polar-

ized outlet only one way. If the plug does not fit fully in the out-

let, reverse the plug. If it still does not fit, contact a qualified

electrician to install a polarized outlet. Do not change the plug

in any way. Double insulation eliminates the need for the three

PERSONAL SAFETY

• Stay alert, watch what you are doing and use common sense

when operating a power tool. Do not use tool while tired or

under the influence of drugs, alcohol, or medication. A

moment of inattention while operating power tools may result in

serious personal injury,

• Dress properly. Do not wear loose clothing or jewelry. Contain

long hair. Keep your hair, clothing, and gloves away from

moving parts. Loose clothing, jewelry, or long hair can be

caught in moving parts. Air vents often cover moving parts and

should also be avoided.

• Avoid accidental starting. Be sure switch is off before plug-

ging in. Carrying tools with your finger on the switch or plugging in

tools that have the switch on invites accidents.

• Remove adjusting keys or switches before turning the tool on.

A wrench or key that is left attached to a rotating part of the tool

may result in personal injury.

• Do not overreach. Keep proper footing and balance at all

times. Proper footing and balance enables better control of the tool

in unexpected situations.

• Use safety equipment. Always wear eye protection. Dust mask,

non-skid safety shoes, hard hat, or hearing protection must be

used for appropriate conditions.

TOOL USE AND CARE

• Use clamps or other practical way to secure and support the

workpiece to a stable platform. Holding the work by hand or

against your body is unstable and may lead to loss of control.

• Do not force tool. Use the correct tool for your application. The

correct tool will do the job better and safer at the rate for which it is

designed.

• Do not use tool if switch does not turn it on or off. Any tool that

cannot be controlled with the switch is dangerous and must be

repaired.

• Disconnect the plug from the power source before making

any adjustments, changing accessories, or storing the tool.

Such preventative safety measures reduce the risk of starting the

tool accidentally.

• Store idle tools out of reach of children and other untrained

persons. Tools are dangerous in the hands of untrained users.

• Maintain tools with care. Keep cutting tools sharp and clean.

Properly maintained tools, with sharp cutting edges are less likely

to bind and are easier to control.

• Check for misalignment or binding of moving parts, breakage

of parts, and any other condition that may affect the tools

operation. If damaged, have the tool serviced before using.

Many accidents are caused by poorly maintained tools.

• Use only accessories that are recommended by the manufac-

turer for your model. Accessories that may be suitable for one

tool, may become hazardous when used on another tool.

SERVICE

• Tool service must be performed only by qualified repair

personnel. Service or maintenance performed by unqualified

personnel could result in a risk of injury.

• When servicing a tool, use only identical replacement parts.

Follow instructions in the Maintenance section of this manu-

al. Use of unauthorized parts or failure to follow Maintenance

Instructions may create a risk of electric shock or injury.

Additional Safety Rules

• Hold tool by insulated gripping surfaces when performing an

operation where the cutting tools may contact hidden wiring

or its own cord. Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

• Keep handles dry, clean, free from oil and grease. It is recom-

mended to use rubber gloves. This will enable better control

• DO NOT TOUCH ANY METAL PARTS OF THE TOOL when

drilling or driving into walls, floors or wherever live electrical

wires may be encountered. Hold the tool only by insulated

grasping surfaces to prevent electric shock if you drill or drive into

a live wire.

English

CAUTION: Wear appropriate hearing protection during use.

Under some conditions and duration of use, noise from this product

may contribute to hearing loss.

WARNING: Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities contains chemicals known to

cause cancer, birth defects or other reproductive harm. Some exam-

ples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety equip-

ment, such as those dust masks that are specially designed to filter

out microscopic particles.

• Avoid prolonged contact with dust from power sanding, saw-

ing, grinding, drilling, and other construction activities. Wear

protective clothing and wash exposed areas with soap and

water. Allowing dust to get into your mouth, eyes, or lay on the skin

may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disburse dust,

which may cause serious and permanent respiratory or other injury.

Always use NIOSH/OSHA approved respiratory protection appropri-

ate for the dust exposure. Direct particles away from face and body.

•

The label on your tool may include the following symbols. The sym-

bols and their definitions are as follows:

V..........volts A ..........amperes

Hz........hertz W ..........watts

min ......minutes ........alternating current

....direct current

o ........no load speed

English

FIG. 1

FIG. 2

REVERSING

LEVER

(Shown in Forward

Position)

FIG. 3

SWITCH ASSEM-

BLY

220 VOLT PLUG

LOCK-OUT KEY

........Class II Construction …/min ..revolutions or

........earthing terminals ..............reciprocation per minute

........safety alert symbol

Anti-Lock Control (DW239, DW249)

Your DEWALT drill may come with an electronic feature called Anti-

Lock Control. It is designed to help you control the drill during a stall

and keep it from pulling out of your hands. This may be encountered

when drilling in steel or using large bits in wood.

As a stall situation presents itself, the motor cycles on and off for a set

period of time. This takes up the reaction of the stall and allows you to

keep the drill under control. The speed control senses your release of

the trigger and resets the motor to run again.

Figure 4 shows the instruction label mounted behind it. There are

three alert signals.

1. Check Level: One flash each time the trigger is depressed.

Everything is functioning satisfactorily. If there is no flash, the tool

should be returned to a D

EWALT authorized service center for

repair.

2. Engaged Level: Should a stall condition still exist, the electronics

will shut down the tool and the light will be steady on. When the

unit is running in normal mode, there will be no light.

3. Alert Mode: A series of continual flashes as the trigger is pulled

indicates that the electronics are no longer functioning. The tool

may still be able to function without the benefit of AntiLock Control

but should be serviced as soon as possible.

Motor Brushes

DEWALT uses an advanced brush system which automatically stops

the drill when the brushes wear out. This prevents serious damage to

the motor.

Switch

To start drill, depress trigger switch; to stop the drill, release trigger. To

lock trigger in the on position for continuous operation, depress trigger

and push up locking button “A” shown in figure 1, then gently release

the trigger. To release the locking mechanism, depress the trigger fully,

then release it. Before using the tool each time, be sure that the lock-

ing button release mechanism is working freely.

Do not lock the switch on when drilling by hand so that you can

instantly release the trigger switch if the bit binds in the hole.

The locking button is for use only when the drill is mounted in a drill

press stand or otherwise held stationary.

Be sure to release the locking button before disconnecting the plug

from the power supply. Failure to do so will cause the tool to start

immediately the next time it is plugged in. Damage or injury could

result.

THE VARIABLE SPEED TRIGGER SWITCH

This switch permits speed control: the farther the trigger is depressed,

the higher the speed of the drill.

NOTE: Use lower speeds for starting holes without a center punch,

drilling in metal or plastics, driving screws or drilling ceramics. Higher

speeds are better for drilling wood and composition boards, and for

using abrasive and polishing accessories.

English

FIG. 4

SPINDLE LOCK

BUTTON

ANTI-LOCK CONTROL

INSTRUCTION LABEL

INDICATOR LIGHT

THE REVERSING LEVER

The reversing lever changes the direction of rotation of the drill and is

used when backing out screws and jammed drill bits. To operate the

tool in reverse, release the trigger switch and push the lever to the left

(when viewed from the chuck end) as shown in Figure 2. To operate

the drill in forward for drilling holes or driving screws (as well as when

using other accessories) release the trigger switch and push the lever

to the right (when viewed from the chuck end).

Return the reversing lever to the forward position after all operations

in reverse are completed.

SWITCH LOCK-ON

Your drill is equipped with a switch lock-on feature. If you wish to dis-

able this feature, take your tool to any authorized service center. The

service center can provide a lock-out key to prevent the unit from

being locked in the on position (Figure 3).

Operation

DRILLING

1. Always unplug the drill when attaching or changing bits or acces-

sories.

2. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits,

power auger bits, or hole saws. For METAL, use high speed steel

twist drill bits or hole saws. For MASONRY, such as brick, cement,

cinder block, etc., use carbide-tipped bits.

3. Be sure the material to be drilled is anchored or clamped firmly. If

drilling thin material, use a wood “back-up” block to prevent damage

to the material.

4. Always apply pressure in a straight line with the bit. Use enough

pressure to keep the drill biting, but do not push hard enough to

stall the motor or deflect the bit.

5. Hold the tool firmly to control the twisting action of the drill.

6. IF THE DRILL STALLS, it is usually because it is being overloaded

or improperly used. RELEASE THE TRIGGER IMMEDIATELY,

remove the drill bit from work, and determine cause of stalling. DO

NOT CLICK TRIGGER OFF AND ON IN AN ATTEMPT TO

START A STALLED DRILL — THIS CAN DAMAGE THE DRILL.

7. To minimize stalling or breaking through the material, reduce pres-

sure on drill and ease the bit through the last fractional part of the

hole.

8. Keep the motor running when pulling the bit out of a drilled hole.

This will help prevent jamming.

9. With Variable Speed Drills there is no need to center punch the

point to be drilled. Use a slow speed to start the hole and acceler-

ate by squeezing the trigger harder when the hole is deep enough

to drill without the bit skipping out.

Keyed Chucks

Open chuck jaws by turning collar with fingers and insert shank of bit

about 3/4" into chuck. Tighten chuck collar by hand. Place chuck key in

each of the three holes, and tighten in CLOCKWISE direction. It’s

important to tighten chuck with all three holes to prevent slippage. To

release bit, turn chuck key COUNTERCLOCKWISE in just one hole,

then loosen the chuck by hand. Any authorized D

EWALT service center

can install a keyless chuck in place of a keyed chuck.

Keyless Chucks

Open chuck jaws by turning plastic collar with fingers and insert shank

of bit about 3/4" into chuck. Tighten plastic collar CLOCKWISE while

depressing spindle lock button on the right side of the tool housing

(Fig. 4). To release bit, turn plastic collar COUNTERCLOCKWISE

while depressing the spindle lock button (Fig. 4).

NOTE: DO NOT DEPRESS LOCK BUTTON WHILE OPERATING

DRILL or while the chuck is moving.

Drilling in Metal

Use a cutting lubricant when drilling metals. The exceptions are cast

iron and brass which should be drilled dry. The cutting lubricants that

work best are sulfurized cutting oil or lard oil; bacon-grease will also

serve the purpose.

English

Drilling in Wood

Holes in wood can be made with the same twist drills used for metal.

These bits may overheat unless pulled out frequently to clear chips

from the flutes. For larger holes, use power drill wood bits. Work that

is apt to splinter should be backed up with a block of wood.

Drilling in Masonry

Use carbide tipped masonry bits at low speeds. Keep an even force

on the drill but not so much that you crack the brittle materials. A

smooth, even flow of dust indicates the proper drilling rate.

Side Handle

A side handle may be supplied with your drill. Side handles are includ-

ed with these drills: DW231, DW235G, DW235-220, DW236, DW238,

DW239, DW245, DW246, DW248, DW249. The side handle clamps

to the front of the gear case and can be rotated 360 degrees to permit

right or left hand use.

CAUTION: If a side handle is included with your drill, always use it

and hold the drill with both hands.

Maintenance

Use only mild soap and damp cloth to clean the tool. Never let any liq-

uid get inside the tool; never immerse any part of the tool into a liquid.

Self-lubricating bearings are used in the tool and periodic relubrication

is not required. In the unlikely event that service is ever needed, take

your tool to an authorized service location.

Accessories

Recommended accessories for use with your tool are available at extra

cost from your distributor or local service center. ACCESSORY MUST

BE RATED FOR USE AT SPEED EQUAL TO OR HIGHER THAN

NAMEPLATE R.P.M. OF TOOL WITH WHICH IT IS BEING USED.

If you need assistance in locating any accessory, please contact

EWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD

21286 or call 1-800-4- D

EWALT (1-800-732-4441).

CAUTION: The use of any non-recommended accessory may be

hazardous.

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment (including brush inspection and replacement) should

be performed by authorized service centers or other qualified service

organizations, always using identical replacement parts.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materi-

als or workmanship for three years from the date of purchase. This

warranty does not cover part failure due to normal wear or tool abuse.

For further detail of warranty coverage and warranty repair informa-

tion, visit www.dewalt.com or call 1-800-4-D

EWALT (1-800-433-9258).

This warranty does not apply to accessories or damage caused where

repairs have been made or attempted by others. This warranty gives

you specific legal rights and you may have other rights which vary in

certain states or provinces.

In addition to the warranty, D

EWALT tools are covered by our:

1 YEAR FREE SERVICE

EWALT will maintain the tool and replace worn parts caused by nor-

mal use, for free, any time during the first year after purchase.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

EWALT Power Tool, Laser, or Nailer for any reason, you can return it

within 90 days from the date of purchase with a receipt for a full refund

– no questions asked.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-DEWALT for a free

replacement.

English

Page is loading ...

DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (JUL04-CD-1) Form No. 626352-00

EWALT

The following are trademarks for one or more D

EWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array

of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.

DeWalt DW223-220 User manual

Brand: DeWalt

Model: DW223-220

Category: Power tools

Type: User manual

Download PDF

report

in other languages

français: DeWalt DW223-220 Manuel utilisateur
español: DeWalt DW223-220 Manual de usuario

DeWalt DW223-220 User manual

DeWalt DW223-220 User manual

in other languages

Related papers

Other documents