Craftsman 580.752100 Owner's manual

Brand: Craftsman

Model: 580.752100

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

Operator'sManual

2780 PSi MAX

2.5 GPff] MAX

_odei No. 580.752160

PRESSUREWASHER

CUSTOMERHELPLINE

HOUriS: Non. - Fri. 8 a.m. to 5p.m. (CT)

wAReeeG

Before usingthis product, readthis

manualand follow atI SafetyRutes

and Operating Instructions.

ADVER'rENCmA

Antes de utiiizar el producto, Ieaeste

manuaiy siga todas IasReglasde

Seguridade Instrucciones deUso.

Sears, Roebuck and Ca., Hoffman Estates, _L 68179 U.S.A.

Visit our Craftsman website: www.craftsman.eom

Part No. 202663GS Draft B(04/04/2007)

®Safety

®Assembly

®Operation

,, Maintenance

,, Parts

,, Espa_oi,p. 32

WARRANTY.......................................... 2

SAFETYRULES...................................... 2-5

FEATURESANDCONTROLS.............................. 6

ASSEMBLY......................................... 7-9

OPERATION....................................... 10-13

SPECIFICATIONS..................................... 14

MAINTENANCE.................................... 15-19

STORAGE........................................... 20

TROUBLESHOOTING.................................. 21

REPLACEMENTPARTS.............................. 22-29

EMISSIONCONTROLWARRANTY..................... 30-31

ESPANOL......................................... 32-55

HOWTOORDERPARTS........................ BACKPAGE

If this pressurewasher faiis dueto a defectin materiai or workmanship within oneyear from the dateof purchase,return it to

any Searsstore, other Craftsman outlet, or SearsParts & RepairCenterin the UnitedStates or Canadafor free repair (or

replacementif repairproves impossible).

Ali warranty coverageapplies for only 90 days from dateof purchaseif this pressure washer is ever usedfor commercial or

rentaipurposes.

This warranty gives you specific legal rights, and you mayalso haveother rights which vary from stateto state.

Sears, Roebuck and Ce,, Heffman Estates, JL68179

Sears Canada Jnc,, Terente, 8ntarie, Canada MSB 2B8

Thisis the safety alert symbol, tt is used to alert yea to potentialpersenaminjary hazards. ObeyaHsafety messages

that fellow this symbemto avoid pessiNe injuryor death.

_Read this manual carefully and become familiar

..... with yourpressurewasher. Knew its applications,

itslimitations, and any hazardsinvolved.

Thesafety alert symboi (,_) is usedwith a signal word

(DAr/GER,CAUTION,WARNING),a pictorial and/or a safety

messageto alert you to hazards.BANGERindicatesa hazard

which, if not avoided, wi/'/resuIt in deathor serious injury.

WARNINGindicates a hazardwhich, if not avoided, cou/d

result in deathor serious injury. CAUTtONindicatesa hazard

which, if not avoided, might result in minor or moderate

injury. NOTICEindicatesa situation that could result in

equipment damage. Foiiow safety messagesto avoid or

reducethe risk of injury or death.

Hazard $ymhomsand NteanJngs

ToxicFurnes

SlipperySurface

Fire

Kickback ElectricalShock

Fall FluidInjection

Explosion Operator'sManual

MovingParts FlyingObiects HotSurface

Runningenginegivesoffcarbonmonoxide,an

odorless,coioriess,poisongas.

Breathingcarbonmonoxidecancauseheadache,

fatigue,dizziness,vomiting,confusion,seizures,

nausea,faintingordeath.

Somechemicaisordetergentsmaybeharmfulif

inhaledoringested,causingseverenausea,

fainting,orpoisoning.

• OperatepressurewasherONLYoutdoors.

o Keepexhaustgasfromenteringaconfinedareathrough

windows,doors,ventilationintakes,or otheropenings.

o DONOTstartor runengineindoorsor in anenclosedarea,

evenif windowsanddoorsareopen.

• Usea respiratoror maskwheneverthereisa chancethat

vaporsrnaybeinhaled.

• Readall instructionswith masksoyouarecertainthernaskwill

providethenecessaryprotectionagainstinhalingharmful

vapors.

WARNING

_¢ Risk of electrocution.

Contact with power source can cause electric

shock or burn.

• NEVERspray nearpower source

WARNING

_'_ Fuet and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHENARRmNG ORBRAINING FUEL

o Turn pressure washer OFFand let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relievepressure

in tank.

o Fill or drain fuel tank outdoors.

• DONOTover% tank. Mow spacefor fue! expansion.

o If fuel spills, wait until it evaporatesbefore starting engine.

• Keepfuel away frorn sparks, openflames, pilot lights, heat,and

other ignition sources.

• DONOTlight a cigarette or smoke.

WHENSTARTINGEQUmP_'IENT

o Ensure spark plug, muffler, fuel cap, andair cleaner arein

place.

o DO NOTcrank enginewith spark plug removed.

WHENOPERATINGEQUIP_tENT

• DONOTtip engine or equiprnentat anglewhich causesfuel to

spill

o DONOTspray'flamrnable liquids.

WHENTRANSPORTmNGOR REPAIRmNGEQNIPI_IENT

o Transport/repair with fuel tank EMPTYor with fuel shutoff valve

OFF.

o Disconnect spark plug wire.

WHENSTORINGFUEL OR EQUIPMENTWiTH FUELmNTANK

• Store away from furnaces, stoves_water heaters_clothes

dryers, or other appliances that have pilot light or other ignition

source becausethey'can ignite fuel vapors.

WARNING

Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pulI hand and arm

toward engine faster than you can Iet go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVERpull starter cord without first relieving spray gun

pressure.

o When starting engine pull cord slowly until resistanceis felt

andthen pul! rapidly to avoid kickback.

o After eachstarting atternpt where enginefails to run, always

point spray gun in safe direction andsqueezespray gun trigger

to releasehigh pressure. Engagespray gutstrigger lock.

o Firmly grasp spray gun with both hands when using high

pressure spray to avoid iniury when spray gun kicks back.

WARNING

Useof pressure washer cancreate puddles and

slippery surfaces,

Kickbackfrom spray gun cancause you to fall,

* Operatepressure washer frorn astable surface.

o The cleaningarea should haveadequate slopes and drainageto

reducethe possibility of afall due to slippery surfaces.

o Be extremelycareful if you rnust usethe pressurewasher from

a ladder,scaffolding, or any other similar location.

o Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING

Contact with muffler area can result inserious

burns.

Exhaustheat/gases can ignite combustibles,

structures or damagefuel tank causing afire.

* DO NOTtouch hot parts andAVOID hot exlsaustgases.

* Allow equipment to cool before touching.

o Keepat least 5feet (152 crn) of clearanceon all sides of

pressure washer including overhead.

o Codeof FederalRegulation (CFR)Title 36 Parks,Forests,and

Public Property require equipment powered by an internal

combustion engine to have aspark arrester, rnaintainedin

effective working order, complying to USDAForestservice

standard 5100-1C or later revision. Inthe State of California a

spark arrester is requiredunder section 4442 of the California

Public resources code. Other statesrnay havesimilar laws.

pressure stream of water that thi-['s_

equipment produces can cut through skin and its

_ .underlying tissues, ieading to serious injury and

possibie amputation.

_l"_ Spray gun traps h gl water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

DONOTallow CHILDRENto operate pressure washer.

NEVERrepair high pressure hose. Replaceit.

NEVERrepair leakingconnections with sealantof any kind.

Replaceo-ring or seal.

NEVERconnect high pressure hoseto nozzle extension.

Keephigh pressure hose connectedto purnp and spray gun

while system is pressurized.

ALWAYSpoint spray gun in safe direction and squeezespray

gun trigger to releasehigh pressure, everytime you stop

engine. Engagetrigger lock when not in use.

NEVERaim spray gutsat people,animals, or plants.

DO NOTsecure spray gun inopen position.

DO NOTleavespray gun unattended while rnacbineis running.

NEVERusea spray gun wlsichdoes not haveatrigger lock or

trigger guard in place and in working order.

Always be certain spray gun, nozzbs and accessoriesare

correctly attached.

WARNING

Unintentionalsparking can result in fire or

_¢ electrb shock.

WHENADJNSTmNGOR_IAKtNGREPAIRSTOYOURPRESSURE

WASHER

o Disconnectthe sparkplugwirefromthesparkplugandplace

thewirewhereit cannotcontactsparkplug.

WHENTESTmNGFORENGINESPARK

o Useapprovedsparkplugtester.

• DONOTcheckfor sparkwith sparkplugremoved.

WARNING

Starter and other rotating parts canentangie

hands, hair, clothing, or accessories.

• NEVERoperatepressurewasherwithoutprotectivehousingor

covers.

• DONOTwea!looseclothing jewelryor anythingthat maybe

caughtinthestarteror otherrotati_gparts.

o Tieup longhai!andrernovejewelry.

WARNING

IRisk of eyeinjury=

..L..__jSpray cansplash backor propel objects.

Alwayswearsafetygoggleswhenusingthis equipmentor in

vicinityof whereequipmentisin use.

Beforestartingthepressurewasher,besureyouarewearing

adequatesafetygoggles.

NEVERsubstitutesafetyglassesfor safetygoggles.

High pressure spray may damagefragiie items inciuding

lass.

DONOTpointspraygunatglasswhenusingMAX(0°) nozzle.

NEVERaimspraygunatplants.

Improper treatment of pressure washer can damageit and

shorten its iife.

Ifyouhavequestionsaboutintendeduse,askdealeror contact

Sears.

NEVERoperateunitswith brokenor missingpa!rs,or without

protectivehousingor covers.

DONOTby-passanysafetydeviceonthis rnachine.

DONOTtamperwith governedspeed.

DONOToperatepressurewasheraboveratedpressure.

DONOTmodifypressurewasherinanyway.

Beforestartingpressurewasherincoldweathercheckall parts

oftheequiprner_tto besureicehasnotformedthere.

NEVERmovemachinebypullingon hoses.Usehandle

providedon unit.

Checkfuelsystemfor leaksor signsofdeterioration,suchas

chafedor spongyhose,looseor missingclamps_or damaged

ta!_korcap.Correctalldefectsbeforeoperatingpressure

washer.

Thisequipmentisdesignedto beusedwith Searsauthorized

partsONLY.If equipmentis usedwith partsthatDONOT

complywith minimumspecifications,userassumesall risks

andliabilities.

KNOWYOURPRESSUREWASHER

,r' F I-_Read the Operator's ManuaJand safety ruJesbefore operating yourpressurewasher.

.... Comparethe illustrations with your pressurewasher to familiarizeyourself with the locations of various controls and

adjustments. Savethis manualfor future reference.

A =Spray Gun-- Controisthe appiication of water onto

cleaningsurfacewith trigger device,inctudestrigger iock.

B oPresisieeSprayTM SeJestor-- Containssix different

setting for various appiications.

C- Cleaning Tank - Usedto provide pressure washer safe

detergents into the iow pressurestream.

D -Resoil Starter -- Used for starting the engine manuatiy.

E - Fuel Tank-- FilItank with reguiar unleadedfuel. Aiways

leaveroom for fuei expansion.

F =Warning/Operating instructions Tag-- Identifies hazards

and proper procedureto start/stop pressure washer,

G - Air Filter -- Protects engine by fiitering dust and debris

out of intakeair=

H =ThrottleLever-- Setsengine in starting mode for recoil

starter and stops a running engine.

J =Choke Lever -- Preparesa coid engine for starting.

J(- Pamp -- Developshigh pressure=

L - A[itematic CoolDown System-- Cycleswaterthrough

pump when water reaches 125°=155%.Warm water wiii

discharge from pump ontoground. This system prevents

internal pump damage.

Ni- Oil Fill/Dipstick -- Check,add and drain engineeli here=

N =High Press[ireHose -- Connectone end to waterpump

and the other end to spray gun.

P - Accessory Tray -- Provides convenientstorage for

standard and optional accessories,such as brushes,

turbo wands, etc=

items Not Shown:

Data Tag (near rear of base plate) -- Provides model and

serial number of pressurewasher. Pieasehavethese readily

avaiiabieif calling for assistance.

High Press[ire O[itJet-- Connectionfor higil pressure hose.

Safety Goggles-- Always usethe enciosedsafety goggies

when runningyour pressurewasher.

Water inlet -- Connectionfor garden hose.

YourcleaningsystemrequiressomeassembIyandisready

foruseonlyafterithasbeenproperiyservicedwiththe

recommendedoilandfuel.

Jfyou haveany prohbmswith the assembly of your

pressurewasher, please call the pressurewasher hempline

at 1o800o222o3136.

UNPACKTHEPRESSUREWASHER

1. Removeeverything from carton exceptpressure washer.

2. Opencarton completely bycutting eachcorner from top

to bottom.

3. Removepressure washer from carton.

CARTONCONTENTS

Checkali contents, if any parts are missing or damaged,call

the pressure washer hetplineat 1=800=222=3136.

° Main Unit

* Handb with CieaningTankAssembly

, AccessoryTray

° High PressureHose

° Spray Gun

, PrecisionSprayTM Selector

, DetergentSiphoning Hose/Fiiter

* Oil Bottle

, Parts Bag (which includesthe following):

. Operator's Manual

, Owner's RegistrationCard

, SafetyGoggies

, HandieFasteningHardwareKit (whichincludes):

, CarriageBolts (2)

, Plastic Knobs (2)

, Tree6iips (4)

Becomefamiiiar with eachpiecebefore assembiingthe

pressure washer. Identify alIcontents with the illustration on

page 6. if any parts are missing or damaged,callthe

pressure washer helptineat 1-808-222-3136.

A$$EJ IBLINGCLEANINGSYSTEJ

Your Craftsmancleaningsystem will needassembly before

operation:

1. Fiii out andsend in registration card.

2. Attach handieand accessorytray.

3. Connectdetergent siphon hoseto pump.

4. Add elito enginecrankcase.

5. Add fuel to fuel tank.

6. Connectpressure hoseto spray gunand pump.

7. Connectwater supply to pump.

8. Attach PrecisionSprayTM Selector to spraygun.

Attach Handle and Accessery Tray

1. Placehandb (A) onto handb supports (8) connectedto

main unit. Makesure holes (C) in handb align with holes

NOTE:it may be necessaryto move the handle supports

from sideto side in order to align the handleso it wifl slide

overthe handIesupports.

2. Insert carriagebolts (A) through holesfrom back of unit

and attacha plastic knob (8) from front of unit. Tighten

by hand.

3. Placeaccessorytray (A) over holes (g) on handle

(viewing from front of unit). Pushthe tree clips (8) into

the holes until they sit fiat againstthe accessorytray.

Insert supplied accessoriesin spacesprovided in

accessorytray. SeeHow to UseAccessofy Tray.

Attach Detergent Siphon Hose te Pemp

Thepressure washer is equippedwith two detergent

siphoning hoses.One is attachedto the cleaningtank and

one is loosefor siphoning pressure washer safe detergents

from a bottle or container.

Attach one of the detergent siphon hoses (A) to the barbed

hose fitting (B) on the pump.

iMPORTANT:Onlyone detergent siphoning hosecan be used

at a time. When cleaningtank is not used, makesure

detergent shut-off valve on cleaningtank is in the "Off"

position.

Add Engine Oil

1. Placepressure washer on a flat, ieveisurface.

2. Cleanarea around oii fiii and remove yeiiow oii fiii

cap/dipstick.

NOTE:See 0i/Recommendations in Maintenancesection.

Verify provided oil bottle is the correct viscosity for current

ambient temperature.

3. Using oiI funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

NOTICE

improper treatment of pressurewasher can damageit and

shorten its life.

DONOTattempttocrankor sta!ttheenginebeforeit hasbeen

properlyservicedwiththerecommendedoil.Thismayresultin

anenginefailure.

4. Replaceoil fill cap/dipstick and fully tighten.

Add Fee?

Fuel must meet these requirements:

Clean,fresh, unleadedgasoline.

. A minimum of 87 octane/87AKI (91 RON).Highaltitude

use, see HighAltitude.

° Gasolinewith up to 10%ethanol (gasohoI) or up to

15% MTBE(methyl tertiary butyi ether) is acceptable.

Avoid pressure washer damage.

Faiiumto foliow Operator's Manuaifor fuet

recommendations voids warranty.

DONOTuseunapprovedgasolinesuchasE85.

DONOTmixoil in gasoline.

DONOTmodifyengineto runon alternatefuels.

To protectthefueI systemfrom gum formation, mix in afue!

stabiiizerwhenadding fueLSeeStorage.Ali fueiis not the

same.if you experiencestarting or performanceproblemsafter

usingfue!,switch to a differentfuel provideror changebrands.

This engineis certifiedto operateon gasoiine.Theemission

control systemfor this engineis EM(EngineModifications).

WARNING

Fueiand itsvapors areextremely flammable and

explosive.

Fireor explosioncan causesevere burns or

death.

WHENADEmNGFUEL

• TurnpressurewasherOFFandletit coolatleast2 minutes

beforeremovingfuelcap.Loosencapslowlyto relievepressure

in tank.

• Fillfueltankoutdoors.

o DONOToverfilltank.Allowspaceforfuelexpansion.

• Iffuelspills waituntilit evaporatesbeforestartingengine.

o Keepfuelawayfrornsparks,openflames,pilotlights,heat,and

otherignitionsources.

• DONOTlighta cigaretteorsmoke.

1. Cieanareaaround fuel fiii cap, removecap.

2. Siowiy add regular unleadedfuel (A) to fuettank (B). Be

carefui not to overfiii. Aiiow about 1.5" (4 cm) (C) oftank

space for fuel expansion.

CAUTION! AIcohoI-blendedfuels (caiiedgasohot,ethanol or

methanol) canattract moisture, which leadsto separationand

formation of acids during storage.Acidic gas candamagethe

fuel system ofan engine while in storage.

To avoidengineproblems,the fuelsystemshould betreated

with afuel preserveror emptiedbeforestorageof 30 days or

longer,if addinga fuel preserver,fiii the fuei tank with fresh

fuel. if oniy partiaiiy fiiied, air inthe tank wiii promote fuel

deterioration during storage. If fuel preserver is not used,

drainthefueI tank,startthe engineand ietit rununtiithe fuel

linesandcarburetorare empty. Usefreshfuel nextseason.See

Storagefor additionalinformation.

NEVERuseengine orcarburetor cleaner products in the fuel

tank as permanentdamagemay occur.

Ataltitudesover5,000feet(1524meters),aminimum

85octane/ 85 AKI (89 RON)gasoline is acceptable.To

remain emissions compiiant, high attitudeadjustment is

required. Operationwithout this adjustment wiii cause

decreasedperformance, increasedfuel consumption, and

increasedemissions. Seea qualified Searsdealer for high

altitude adjustment information. Operationof the engineat

altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

Cennect Hese and Water Supply te Pump

NOTE:Removeand discard the shipping capsfrom the

pump's high pressureoutiet andwater inlet before attaching

hoses.

1. Uncoii high pressure hoseand attach one end of hoseto

baseof spray gun. Tighten by hand.

WARNING

The high pressure stream of waterthat this

equipment producescancut through skin and its

underlyingtissues, leadingto serious injury and

)ossibb amputation.

* NEVERconnecthighpressurehoseto nozzbextension.

* Keephighpressurehoseconnectedto purnpandspraygun

whilesysternis pressurized.

. Alwaysbecertainspraygun,nozzlesandaccessoriesare

correctlyattached.

Attach other end of high pressurehoseto high pressure

outlet on pump. Tightenby hand.

3, Beforeconnecting garden hoseto water inlet,inspect

inletscreen. Cleanscreen (A)if it contains debris or have

it replacedif damaged.DONOTrun pressurewasher if

inletscreen is damaged or missing,

Runwater through garden hosefor 30 secondsto flush

it of debris.Turn off water.

iMPORTANT:DONOTsiphon standing water for the water

supply. UseONLYcoId water (Iessthan 100%).

5. Connectgarden hose(not to exceed50 feetin length) to

water inlet. Tighten by hand.

NOTICE

Using a OneWay Vatve(vacuum breakeror checkvaiv@

at pump inlet cancause pump or iniet connector damage.

ThereMUSTbeatleasttenfeet(3 rn)ofunrestrictedgarden

hosebetweenthepressurewasherinletandanydevice,suchas

avacuumbreakeror checkvalve.

Darnageto equipmentresultingfromfailuretofollowthis

instructionwillvoidwarranty,

6. Turn ONwater, point gun in asafe direction and squeeze

trigger to purge pump system of air and impurities.

WARNING

jRiskof eyeinjury.

_Spray cansplash backor propel objects.

Alwayswearsafetygoggleswhenusingthis equipmentor in

vicinityof whereequipmentisin use.

Beforestartingthepressurewasher,besureyouarewearing

adequatesafetygoggles.

NEVERsubstitutesafetyglassesfor safetygoggles.

ChecMJst Befere Starting Engine

Reviewthe unit to ensureyou haveperformed all of the

following:

1. Besureto read SafetyRu/'esand Operationsections

before usingthe cleaningsystem.

2. Makesure handle is in placeand secure.

3. Checkthat oii has beenaddedto proper level in engine

crankcase.

4. Add properfue! to fueI tank.

5. Checkfor proper hoseconnections (high pressureand

water suppiy) and that thereare no kinks, cuts, or

damageto the high pressure hose.

6. Provideproper water supply (not to exceed 100%).

HOWTOUSEYOURCLEANINGSYSTEM

If you haveany probbms operatingyour pressurewasher,

pleasecallthe pressurewasher heJpfineat 1-800-222-3136,

Pressure Washer Lecation

PressureWasherCJearance

VANNING

Exhaustheat/gases can ignite combustibbs,

structures or damagefuei tank causing afire.

o Keepatleast5ft. (152cm)clearanceonall sidesofpressure

washerincludingoverhead.

Macepressure washer outdoors in anareathat wiii not

accumulate deadtyexhaustgas. DONOTpiacepressure

washer where exhaustgas (A) could accumulateand enter

inside or bedrawn into a potentiaily occupied building.

Ensureexhaustgas is kept awayfrom any windows, doors,

ventiiation intakes, or other openingsthat can aliow exhaust

gasto coiiect in a confinedarea. Prevaiiingwinds and air

currents should betaken into considerationwhen positioning

_ressurewasher.

WARNING

Runningengine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathingcarbon monoxidecan causeheadache,

fatigue, dizziness,vomiting, confusion, seizures,

nausea,fainting or death.

° OperatepressurewasherONLYoutdoors.

o Keepexhaustgasfromenteringaconfinedareathrough

windows,doors,ventilationintakes,or otheropenings.

• DONOTstat or runengineindoorsor in anenclosedarea,

evenif windowsanddoorsareopen.

To Start Your CmeaningSystem

To start your engine=poweredcleaning system for the first

time, foiiow these instructions step=by=step.This information

also applies wheneveryou start the engine after you havelet

the pressurewasher sit idle for at bast a day.

1= Placepressure washer nearan outsidewater source

capableof supplying water at a flow rategreater than

3.5 galions perminute andno iess than 20 PSiat

pressurewasher end of garden hose.

2. Checkthat higil pressure hose istightly connectedto

spray gun and pump. SeeAssemby for illustrations.

3. Makesure unit is in a ieveiposition.

4. Connectgarden hoseto water inteton pressure washer

pump.

5. Turn ONwater, point gun in asafe direction and squeeze

trigger to purge pump system of air and impurities.

6. Attach PrecisionSprayTM Selectorto spray gunaccording

to PrecisionSprayTM Selector instruction sheet.

7. Engagetrigger lock (A) to spray gun trigger.

8. Movethrottle lever (Ai to "Fast position, shown hereas

a rabbit.

9. Move chokeiever (B) to "Choke" position.

NOTE:Fora warm engine,besure the choke leveris in the

"Run" position.

iMPORTANT:Beforestarting the pressurewasher, be sure

ou are wearing adequatesafety goggbs.

WARNING

>_ iRiskof eYeinjurY.

" |Spraycansplash backor propel objects.

Alwayswearsafetygoggleswhenusingthis equipmentor in

vicinityofwhereequipmentisinuse

Beforestartingthepressurewasher,besureyouarewearing

adequatesafetygoggles.

NEVERsubstitutesafetyglassesforsafetygoggles.

lB. Whenstartingengine,positionyourselfas

recommended,grasphandbandpuffrecoiistarter

Jightiyuntilyoufeelsomeresistance,thenpulIbdskiy.

WARNING

Startercord kickback(rapid retraction) can result

in bodily injury. Kickbackwill pulI handand arm

toward enginefaster than youcan iet go.

Brokenbones, fractures, bruises, or sprains

could result.

o NEVERpullstartercordwithoutfirst relievingspraygun

pressure.

• Whenstartingengine_pullcordslowlyuntilresistanceisfelt

andthenpullrapidlyto avoidkickback.

o Aftereachstartingattempt_whereenginefailsto run,always

pointspraygunin safedirectionandsqueezesprayguntrigger

to releasehighpressure.Engagesprayguntriggerlock.

• Firmlygraspspraygunwith bothhandswhenusinghigh

pressuresprayto avoidiniurywhenspraygunkicksback.

1. Return recoii starter slowly. DONOTlet rope"snap

back" against starter.

12. Whenengine starts, slowiy move choke ieverto "Run"

position, asengine warms, if engine falters, move choke

leverto "Choke" position, then to "Run" position.

13. After eachstarting attempt, where enginefails to run,

alwayspoint gun in safe direction and squeezespray

gun trigger to releasehigh pressure. Movechoke lever

to "Choke" position, and repeatsteps 10through 12.

14. If engine faiis to start after six pulis, move choke leverto

"Run" position, and repeatsteps 1Othrough 12.

NOTE:Alwayskeepthe throttle ieverin the "Fast" position

when operatingthe pressurewasher.

WARNING

Thehigh pressurestream of water that thb

equipment producescancut through skin and its

underlyingtissues, ieadingto serious injury and

)ossible amputation.

Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected,

which can causeinjury.

DONOTallowCHILDRENtooperatepressurewasher.

Keephighpressurehoseconnectedto pumpandspraygun

whilesystemis pressurized.

NEVERaimspray'gutsatpeople,animals,or plants.

DONOTsecurespraygun inopenposition.

DONOTleavespraygununattendedwhilernachineis running.

NEVERusea spraygunwhichdoesnothaveatriggerlockor

triggerguardin placeandin workingorder.

Alwaysbecertainspraygun,nozzlesandaccessoriesare

correctlyattached.

WARNING

Contact with muffler area can result in serious

burns.

Exhaustheat/gases can ignite combustibles,

structures or damagefuel tank causing afire.

DONOTtouchhotpartsandAVOIDhotexhaustgases.

Allowequipmenttocoolbeforetouching.

Keepatleast5 feet(152cm) ofclearanceonall sidesof

pressurewasherincludingoverhead.

Codeof FederalRegulation(CFR)Title36 Parks_Forests,and

PublicPropertyrequireequiprnentpoweredbyaninternal

combustionengineto haveasparkarrester rnaintainedin

effectiveworkingorder,complyingto USDAForestservice

standard5100-1Cor laterrevision.IntheStateof Californiaa

sparkarresteris requiredundersection4442oftheCalifornia

Publicresourcescode.Otherstatesmayhavesimilarlaws.

How te Step Your Cleaning System

1. Reieasespray gun trigger and let engine idle for two

minutes.

2. Movethrottle to SLOWposition, then STOPposition.

WARNING

Backfire,fire or enginedamagecould occur.

o DONOTstopenginebymovingchokeleverto "Cheke"position.

3. ALWAYSpointsprayguninasafedirectionandsqueeze

sprayguntriggertoreteaseretainedhighwaterpressure.

iMPORTANT:Sprayguntrapshighwaterpressure,even

whenengineisstoppedandwaterisdisconnected.

WARNING

The high pressure stream of waterthat this

equipment producescancut through skin and its

underlyingtissues, leadingto serious injury and

)ossibteamputation.

Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected,

which can causeinjury.

• Keephighpressurehoseconnectedto purnpandspraygun

whilesystemis pressurized.

o ALWAYSpointspraygunin safedirectionandsqueezespray

guntrigger,to releasehighpressureeverytimeyoustop

engine.Engagetriggerlockwhennotinuse.

4. Engagetrigger lock on spraygun when not in use.

How te 8so Accessory Tray

Theunit is equipped with an accessorytray with placesto

store your spraygun and PrecisionSprayTM Seiector.Thereis

also a hook at the front of the accessorytray to hoid your

high pressurehose. identify alI accessorieswith the

iliustration on page 6.

NOTE:Theextra hoie in the tray is for storing a utiiity brush.

Theextra ciip in thetray is for storing aturbo nozzle.The

brush and turbo nozzieare NOTincludedwith your pressure

washer.You canbuy these items as optional accessories.

1= Mace PrecisionSprayTM Selectorthrougll holeon

accessorytray, as shown.

Mace spray gun through hoteon accessorytray on rigllt

side of unit.

Hanghigh pressurehose on hook attachedto accessory

tray onfront of tray as shown.

How to Use PrecidonSpray TM Sdedor

Referto the PrecisionSprayTM Selectorinstruction sheet for

proper use.

[ NOTICF

Product damagewiii occur if the gun trigger is squeezed

whiie the Selector is in-betweerH_ozziesettings.

NEVERturntheSelectorwhilespraying.

Cteadng and Applying Hetergent

i A CAOT O

NEVERusecausticliquidwithpressurewasher

UseONLYpressurewashersafedetergents/soaps.Followall

rnanufacturersinstructions.

Chemicalscan causebodily injury, and/or property damage.

Teapplydetergentfeiiew thesesteps:

1. Attach oneof the detergentsiphon hosesfoiiowing

instructions Attach DetefgentSiphon Hoseto Pump.

iMPORTANT:Besure engine is off and allowedto cool before

switching detergent siphoning hoses.

WARNING

Contact with muffler area can result in serious

burns.

Exhaustheat/gases can ignite combustibles,

structures or damagefuel tank causing afire.

o DONOTtouchhotpartsandAVOIDhotexhaustgases.

• Allowequipmenttocoolbeforetouching.

2. Preparedetergent soiution as required byjob.

3. Makesure detergent shut=offvalve on cleaning tank is in

"Off" position.

4= If using cleaningtank, pour detergentinto cleaningtank.

NOTE:Thecleaningtank holds one gaiion.

5. RotatePrecisionSprayTM Selector to a iow pressure

position, as described in the PrecisionSprayTM Selector

instuction sheet.

NOTE:Detergentcannot be applied with the PrecisionSprayTM

Seiector in a high pressure position.

6= Makesure garden hose is connectedto water inlet.

Checkthat high pressure hose is connectedto spraygun

and pump.Turn onwater.

NSTICE

You must attachali hosesbefore

Startingtheenginewithoutallthehosesconnectedandwithout

thewaterturnedONwill damagethepump.

Damageto equipmentresultingfrom failureto followthis

instructionwillvoidwarranty.

7. EngagetriggerIockonspraygunandstartengine

foliowinginstructionsHow to Start YourPressure

Washer.

8£ If using cbaning tank, rotatedetergentshut-off valve on

cleaningtank to "On" position (A).

iMPORTANT:if using detergent siphoning hose, makesure

detergent shut-off valve on cleaningtank is in the "Off"

position.

8B. If using detergentsiphoning hose, piacesmali fiiter end

of detergentsiphoning tube into detergentcontainer.

NOTE:Makesure the fiiter is fully submergedin detergent

while applying detergent.

NOTICE

Contact with the hot muffbr candamagedetergent

siphoning tube.

Wheninsertingthefilterintoadetergentsolutionbottle,route

thetubesoasto keepitfrom inadvertentlycontactingthehot

rnuffler.

9. Apply detergentto a dry surface,starting at lower

portion of areato bewashedand work upward, using

long, even, overlapping strokes.

10. Aliow detergentto "soakin"for 3-5 minutes before

washing and rinsing. Re@plyas neededto prevent

surfacefrom drying. DONOTaiiow detergentto dry on

(prevents streaking).

iMPORTANT:When using the detergentsiphoning hose,you

mustflush the detergent siphoning system after eachuse by

placingthe fiiter into a bucketof cteanwater, then run the

pressure washer in Iow pressure for 1-2 minutes.

Pressure Washer Rinsing

After detergentis applied, scourthe surfaceandrinseit clean

asfellows:

f. if using cbaning tank, rotate detergentshut=offvalve on

cleaningtank to "Off" position=

2. Rotate PrecisionSprayTM Selectorto a high pressure

position, asdescribed in the PrecisionSprayTM Selector

instruction sheet.

3. Keepspray gun a safe distancefrom spray surface.

WARNING

Kickbackfrom spray gun cancauseyou to fall.

o Operatepressurewasherfrom astablesurface.

o Beextrerne[ycarefulifyou mustusethepressurewasherfrom

a ladder,scaffolding,or anyothersimilarlocation.

• Firmlygraspspraygunwithbothhandswhenusinghigh

pressuresprayto avoidiniurywhenspraygunkicksback.

4. Apply a high pressure spray to a small areaand then

check the surface for damage.If no damage,proceedto

step 5.

Start at top of areato be rinsed,working down with

same overiapping strokes usedfor cleaning.

Cteaning Detergent $iphening Tube

If you usedthe detergentsiphoning tube,you must flush it

with cleanwater beforestopping the engine.

1. Engagetrigger iock on spray gun.

2. Piacedetergent siphoning tube/filter in a bucketfull of

ciean water.

3. RotatePrecisionSprayTM Selector to a iow pressure

position, as described in the PrecisionSprayTM Selector

instruction sheet.

4. Flushfor 1-2 minutes.

5. Shut off enginefoliowing instructions How to Stop

Pressure Washerand turn off water supply.

6. ALWAYSpoint gun in a safe direction and squeezespray

gun trigger to releaseretained high water pressure.

IMPORTANT:Spraygun traps high water pressure,evenwhen

engineis stoppedand water is disconnected.

WARNING

Thehigh pressurestream of water that this

equipment producescancut through skin and its

_ nderlying tissues, ieadingto serious injupj and

}ossible amputation.

Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected,

which can causeinjupJ.

o Keephighpressurehoseconnectedto purnpandspraygun

whilesystemis pressurized.

• ALWAYSpointsprayguninsafedirectionandsqueezespray

guntrigger,to releasehighpressure,everytimeyoustop

engine.Engagetriggerlockwhennotin use.

autematic Ceel gewn System {Thermal lleiief)

If you run the engineon your pressure washer for

3-5 minutes without pressingthe trigger on the spray gun,

circulating water in the pump can reachtemperatures above

125%. Thesystem engagesto cool the pump by discharging

the warm water onto the ground.

ENGINETECHNICALiNFORtViATION

This is asingle cylinder, overheadvalve (OHV),air cooled

engine, it is aiow emissionsengine.

Inthe Stateof Caiifornia, Model 120000enginesare certified

by the California Air Resources Boardto meetemissions

standardsfor 125 hours. Such certification does not grant

the purchaser, owner or operator of this engineany

additional warranties with respectto the performance or

operational life of this engine.Theengine is warranted soidy

according to the product andemissions warranties stated

elsewherein this manual=

Power Ratings

Thegross power rating for individuaI gas engine models is

labeledin accordancewith SAE(Societyof Automotive

Engineers)codeJ1940 (Small EnginePower & Torque

Rating Procedure),and rating performance hasbeen

obtained andcorrected in accordancewith SAEJ1995

(Revision2002=05).Torquevalues are derived at3060 RPM;

horsepower values are derivedat 3600 RPM.Actuai gross

engine power wiii be lower and is affected by, among other

things, ambientoperating conditions andengine-to-engine

variabiiity. Givenboth the wide array of products on which

enginesare placedand the variety of environmental issues

appiicabb to operatingthe equipment, the gas engine wiii not

developthe ratedgross power when used in a given pieceof

power equipment (actual"on-site"or net power). This

difference is due to a variety of factors including, but not

limited to, accessories (air cteaner,exhaust,charging,

cooiing, carburetor, fuel pump, etc.),appiication iimitations,

ambient operating conditions (temperature,humidity,

altitude), and engine-to-engine variabiiity. Dueto

manufacturing and capacity iimitations, Briggs & Stratton

maysubstitute an engine of higher ratedpower for this

Seriesengine.

PRODUCTSPECiFiCATiONS

PressureWasherSpecifications

Max Outbt Pressure ....................... 2,700 PSi

Max FtowRate............................. 2.5 GPM

DetergentMix ........................ Useasdirected

Water SuppiyTemperature .......... Not to exceed 100%

Shipping Weiglst............................. 71 Ibs.

Engine Specifications

Bore ................................. £69 in. (68mm)

Stroke ............................... £04 in. (52ram)

Displacement ........................ 11.57in. (190 cc)

SparkPlug

Type:..................... Briggs & Stratton 491055S

SetGapTo: ...................... O.020inch(O.50mm)

ArrnatureAir Gap: ........... 0.006-0.014in.(O.15-0.36rnm)

Valveclearancewithvalvespringsinstalledandpiston1/4in,

(6 turn)pasttopdeadcenter(checkwhenengineiscold),

Intake.................... 0.004°0.006in.(0.10=0.15ram)

Exhaust .................. 0.004-0.008in.(O.10-O.20turn)

FuelCapacity............................... 1.6Quarts

OilCapacity....................... 22 Ounces(0.65liter)

NOTE:Forpracticai operation, the engine ioad should not

exceed 85% of rated power. Enginepower will decrease

3-I/2% for each1,000 feet (300 meters) abovesea Ieveiand

1% for each 10° F(5.6° C) above77° F(25° C). It should

operatesatisfactorily at anangle upto 15°.

OWNER'SRESPONSiBiLiTIES

Followthe hourly or calendarintervals, whichever occurs first.

More frequent service is required when operating in adverse conditions noted below.

MABNTENANCESCHEBULE

_ABNTENANCETASK

PRESSUREWASHER

Chec_dcieanwater inlet screen

Check high pressure hose

Check detergent hose

Checkspray gun for leaks

Purge pump of air and contaminants

Prepare pump for storage below 32°F

ENGINE

Before

EachUse

X 1

OPERATINGINTERVALS

Every25 1 Evely 50

Hours or Hours or

Yearly Yearly

See WiRter Storage,

Every lO0

Hours or

Yearly

SERVICEDATES

FILL IN DATESAS YOU COMPLETE

REGULARSERVICE

Check oil level

Clean debris

Changeengine oil

Service air cleaner

Service spark plug

Service spark attester

Clean cooling system

Prepare for storage

If unit is to remain idle for longer than 30 days,

Cleanif clogged. Replaceif perforated or torn.

Change oil after the first (5) operating hours and every 50 hours or yearly thereafter. Changesooner when operating under dirty or dusty conditions.

Replacemore often under dirty or dusty conditions,

GENERALRECOMMENDATIONS

Reguiarmaintenancewill improve the performanceand

extendthe life of the pressurewasher. Seeany Searsor

other qualified service deaierfor service.

Thepressure washer warranty doesnot cover items that

havebeen subjectedto operator abuseor negligence.To

receivefuli valuefrom the warranty, the operator must

maintain pressure washer as instructed in this manual

including proper storage as detaiiedin Storage.

Someadjustments wili needto bemadeperiodicaliy to

properiy maintainyour pressurewasher.

Ali serviceand adjustments should bemadeat ieast once

eachseason.Foiiow the requirementsin the Maintenance

Schedu/echart above.

NOTE:Oncea year you should clean or replacethe spark

ptug and repiacethe air fiiter. Anew spark piug andclean air

fiiter assureproper fuel-air mixture and hetpyour engine run

better and iast longer.

EMiSSiONCONTROL

Maintenance,replacementor repair of the emission control

devicesand systems may be performed by any non-road

engine repair establishment or individual.

BEFOREEACHUSE

1. Checkengine oil Ievei.

2. Cleandebris.

3. Checkwater inlet screen for damage.

4. Checkhigh pressure hose for ieaks.

5. Checkcleaningtank for damage.

6. Checkspray gun for ieaks.

7. Purge pump of air and contaminants.

PRESSUREWASHERMAINTENANCE

CmeanDebris

Daily or before use,clean accumuiated debris from cleaning

system. Keeplinkage, spring and controts ctean.Keeparea

around andbehind muffler free from any combustible debris.

Inspect cooiing air siots andopenings on the pressure

washer. Theseopenings must be kept cleanand

unobstructed.

Cleaningsystem parts should be kept cleanto reducethe risk

of overheating and ignition of accumuiated debris.

o Usea dampcloth to wipe exterior surfaces clean.

, Usea soft bdstie brush to loosencaked on dirt, oil, etc.

, Useavacuumcleanerto pickup loosedirtanddebris.

NOTICE

jlmproper treatment of pressurewasher can damageit and

_horten_ ....

its life.

DONOTinsertanyobjectstbroughcoolingslots.

Check and Clean inlet Screen

Examinegarden hose inlet screen.Cleanif it is clogged or

replaceif it is torn.

Check High Pressure Hese

High pressure hoses can developleaks from wear, kinking,

or abuse,inspect hose beforeeach use. @eck for cuts,

leaks,abrasions, buiging of cover, or damageor movement

of coupiings. If any of these conditions exist, replacehose

immediately.

WARNING

The high pressure stream of waterthat this

_ quipment producescancut through skin and its

underiyingtissues, ieadingto serious injury and

)ossibb amputation.

* NEVERrepairhighpressurehose.Replaceit.

* ReplacementhoseratingMUSTexceedmaxh_nurnpressure

ratingof unit.

Check Spray Gun

Examinehose connectionto spray gun and makesure it is

secure.Testtrigger by pressing it and making sure it springs

back into piacewhenyou releaseit. Put safety iatch in UP

position andtest trigger. You should not beabie to press

trigger. Replacespray gun immediately if it fails any of these

tests.

Hezzle Maintenance

A pulsing sensationfelt while squeezingthe spray gun trigger

may becaused by excessivepump pressure. Theprincipai

cause of excessivepump pressure is a nozzleclogged or

restricted with foreign materials, such asdirt, etc. Tocorrect

the problem, immediately cleanthe nozzlefollowing these

instructions:

1. Shut off engineandturn off water suppiy.

2. ALWAYSpoint spray gun in asafe direction and squeeze

spray gun trigger to releaseretainedhigh water pressure.

WARNING

Thehigh pressurestream of water thatthis

equipment produces cancut through skin andits

_ nderiying tissues, ieading to serious injury and

possible amputation.

Spraygun traps high water pressure, evenwhen

engine is stopped and wateris disconnected,

which cancause injury.

* Keephighpressurehoseconnectedto pumpandspraygun

wbilesystemis pressurized.

o ALWAYSpointspraygunin safedirectionandsqueezespray

gemtrigger,to releasehighpressure,everytimeyoustop

engine.Engagetriggerlockwhennotinuse.

3. Disconnect PrecisionSprayTM Selectorfrom spray gun.

4. Usea smaii paperclip to free any foreign material

clogging or restricting the high pressure nozzies(A).

5. Using a garden hose, removeadditional debris by back

flushing water through PrecisionSprayTM Selector. Back

flush between30 to 60 seconds.

6. ReconnectPrecisionSprayTM Selectorto spraygun.

7. Makesure garden hose is connectedto water iniet.

Checkthat higil pressure hose is connectedto spraygun

and pump.Turn onwater.

8. Engagetrigger Iock onspray gunand start engine

following instructions How to Start Your Pressure

Washe,_

9. Test pressure washer by operating with eachnozzie

selection.

g_lling Maintenance

Purchasean O-Ring RepairKit atyour iocaI Searsor by

cailing l o800-4-MYoHOME(469-4663) or ontineat

www.sears.com, it is not inctudedwith the pressure washer.

This kit includes replacemento-rings, rubber washer and

water inlet fiiter. Referto the instruction sheet provided in the

kit to serviceyour unit's o-rings.

WARNING

Thehigh pressurestream of water that this

_ quipment producescancut through skin and its

underlyingtissues, ieadingto serious injury and

}ossibte amputation.

• NEVERrepairleakingconnectionswitb sealantof anykind.

Replaceo-ringor seal.

Pump Oil Maintenance

DONOTattempt any oiI maintenanceon this pump. This

model doesnot requireany pump oii maintenance.Thepump

is pre°iubricated andseaiedfrom the factory, requiring no

additional lubrication for the life of the pump.

ENGINEMAINTENANCE

WARNING

Unintentional sparking can result in fire or

_ electric shock.

WHENADJUSTmNGORMAKmNGREPNRSTO YOURPRESSURE

WASHER

* Disconnectthe spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHENTESTINGFORENGmNESPARK

* Use approvedspark plug tester.

o DO NOTcheckfor spark with spark plug rernoved.

Oil

oimRecommendations

NOTE:Usea high quality detergentoiIciassified "For Service

SF,SG,SH, SJ" or higher. DONOTusespecial additives.

1. Choosea viscosity according to the table below:

104 F

-22

40 C

o 30

_ 0

-10

-20

-30

NOTE:Synthetic oii meeting iLSACGF-2,APIcertification

markand APi service symboi with "SJ/CF ENERGY

CONSERVING"or higher, is an acceptabieoii at aii

temperatures. Useof synthetic oil does not alter required oil

changeintervals.

SAE30: 40°Fand higher (5°C and higher) isgood for aii

purpose useabove40°F, usebelow 40°F will causehard

starting.

10Wo30:0 to !O0°F(=18to 38°C)is better for varying

temperatureconditions. This viscosity improves coid weather

starting, but may increase oil consumption above80°F

(27%).

*Check oii ieveifrequently at highertemperatures,

Synthetic 5w-3g: =20to 120°F(=30to 40 °C) provides the

best protection at alltemperatures as well as improved

starting with iess oii consumption,

5W-30: 40°Fand below (5°C and be/ow)is recommendedfor

winter useand works best in cold conditions.

CheckingOil Level

OiIlevelshould becheckedprior to each useor at least every

5 hours of operation. Keepoii ievei maintained.

1. Makesure pressure washer is ona ieveisurface.

2. Removeoii dipstick and wipe dipstick with cleancioth.

Reptaceand tigilten dipstick. Removeand and check oil

levei.

3. Verify oiI is at "FuIF' mark on dipstick. Replaceand

tighten dipstick.

1. Makesure pressure washer is ona Ieveisurface.

2. Checkoii ievei as describedin CheckingOffLevel

3. If needed,siowiy pour oil into oil fiii openingto the

"Full" mark on dipstick. DONOToverfill.

Overfiiiing with oil may cause the engine to not start, or

hard starting.

DO NOToverfill.

Ifover the FULLmark on dipstick, drain off to reduce oil levelto

FULLrnark on dipstick.

4. Replaceand tigllten dipstick.

Changeengine oii after the first 5 hours and every 50 hours

thereafter, if you are usingyour pressure washer under

extremeiy dirty or dusty conditions, or in extremely hot

weather, changeoil more often.

CAUTION

Avoid proionged or repeatedskin contact with used motor

oil.

Usedmotoroil hasbeenshownto causeskincancerincertain

laboratoryanimals.

Thoroughlywashexposedareaswith soapandwater.

KEEPOUTOFREACHOFCHILDREN.DON'T

POLLUTE.CONSERVERESOURCES.RETURN

USEDOILTOCOLLECTIONCENTERS.

Changeoil whileengineisstill warmfrom running,asfollows:

1. Drainfuel tank by running pressurewasher until fuel

tank is empty.

2. Disconnectspark plugwire andkeepit awayfrom spark

plug.

3. Cleanarea around oil fill, remove oil fill cap/dipstick.

Wipe dipstick clean.

4. Tipyour pressurewasher to drain eli from eli fiii into a

suitabie container making sure you tip your unit away

from spark plug. When crankcaseis empty, return

pressure washer to upright position.

5. Slowly pour recommended oil (about 20 oz.) into oil fill

opening. Pauseto permitoil to settle. Fillto "Full" mark

on dipstick.

6. Wipe dipstick cleaneachtime oil levelis checked. DO

NOToverfill.

7. Replaceand tigllten dipstick.

8. Wipe up any remaining eli.

g. Reconnectspark plug wire to spark plug.

Service Air Cteaner

Your enginewiil not run properly andmay be damagedif you

run it with a dirty air cteaner.

Servicethe air cleaneronce every 25 hours of operation or

once eachyear, whichever comes first. Service more often if

operating under dirty or dusty conditions. Replacementsare

availableatyour local Searsservicecenter.

Teservicethe air cleaner,follow these steps:

1. Loosentwo screws (A) and lift off cover (B).

2. Carefully removeair cleaner (C)from base(D).

3. Instati ciean (or new) air cleanerin base. Air cleaner

must fit securely in base.

4. Placecover over air cleanerand tighten screws.

NOTE:You can purchase newair filter elements by caIling

l=800o4=MY=HO_,IE(459-4663).

Service Spark Plu9

Servicethe spark piug every 1O0hours of operation or

yearly, whichever occurs first.

1. Cleanareaaround spark piug.

2. Removeand inspect sparkplug.

3. Repiacespark plug if electrodesare pitted, burned or

porcelainis cracked.Usethe recommended replacement

plug. See Specifications.

4. Checkelectrode gap with wire feelergauge and set spark

plug gap to 0.020 inch (0.50 ram) if necessary.

5. Instali spark piugand tighten firmly.

NOTE:You canpurchase a new spark plug bycalling

l=800o4=MY=HOME(469o4663).

Spark AttesterService

Your engineis not factory=equippedwith a spark arrester. In

some areas,it is iiiegaito operatean engine without a spark

arrester. Checkiocai iaws and regulations. A spark attester is

avaiiablefrom your nearest Searsservicecenter, if you need

to order a spark arrester, pleasecall 1-800-4-MY-t-tOME

(469=4663).

Thespark arrester must be serviced every50 hours to keepit

functioning asdesigned.

If the engine hasbeen running, the muffler wiii be very hot.

Ailow the muffler to cool before servicingthe sparkarrester.

WARNING

_ ontact with muffler area can resuit in serious

burns.

Exhaustheat/gases can ignite combustibles,

structures or damagefuel tank causing afire.

o DO NOTtouch hot parts and AVOIDhot exhaust gases.

• Allow equipment to cool beforetouchh]g.

o Keepat least5 feet (152 cm) of clearanceon all sides of

pressure washer including overhead.

• Codeof FederalRegulation (CFR)Title 36 Parks,Forests, and

Public Property require equlprnent powered by an inten]al

cornbustion engineto haveaspark arrester rnaintainedin

effective working order, complying to USDAForestservice

stal]dard 5100-16 or later revbion. Inthe Stateof 6alifornia a

spark arrester is required undersection 4442 of the California

Public resources code. Other statesmay havesimilar laws.

Remove spark arrester screen for cleaning and inspection.

• Replace if screen is damaged.

Air Ceomin9System

Overtime debris may accumulate in cylinder cooiing fins and

cannot be observed without partiai engine disassembly. For

this reason,we recommendyou havean qualified Sears

servicedealer cleanthe cooling system per recommended

intervals (see MaintenanceSchedub). Equaliyimportant is to

keeptop of engine freefrom debris. See@'eanDebris.

AFTEREACHUSE

Water should not remain in the unit for iong periods of time.

Sedimentsor minerals candeposit on pump parts and

"freeze" pump action. Followthese proceduresafter every

USe:

1. Ftushdetergentsystem byturning its detergent shut-off

valveto "Off" position and run pressurewasher with

PrecisionSprayTM Selector in aiow pressureposition.

Flushfor one to two minutes.

2. Shut off engine,turn off water supply, point gun in a

safe direction and squeezetrigger to relievetrapped

pressure,engagetrigger lock olsspray gun andlet

enginecoot.

WARNING

The high pressure stream of waterthat this

equipment producescancut through skin and its

_ nderiying tissues, ieadingto serious injury and

)ossibieamputation.

Spray gun traps high water pressure,evenwhen

engine is stopped and water is disconnected,

which can causeinjury.

* Keephighpressurehoseconnectedto pumpandspraygun

whilesystemis pressurized.

o ALWAYSpointspraygunin safedirectionandsqueezespray

guntrigger,to releasehighpressureeverytimeyoustop

engine.Engagetriggerlockwhennotinuse.

3. Disconnect hosefrom spray gun and high pressure

outbt on pump. Drainwater from hose,gun, and nozzie

extension. Usea ragto wipe off the hose.

4. Empty pump of aii pumped iiquids by puIiing recoii

handb about6 times. This should remove most liquid in

pump.

5. 6oiI high pressure hoseand properly hangit on hook

provided on accessorytray.

6. Store unit ina dean, dry area.

7. If storing for morethan 30 dayssee Long Term ,Storage

on nextpage.

WARNING

Fueiand its vapors areextremely flammable and

expiosive.

Fireor explosion cancause severeburns or

death.

WHENSTORiN6_FUELOREQUIP_IE_JTWiTHFUELI_JTANK

° Storeawayfromfurnaces,stoveswaterheaters,clothes

dryers or otherappliancesthathavepilotlightor otherignition

sourcebecausetheycanignitefuelvapors.

WINTERSTORAGE

Toprotectthe unit from freezingtemperatwres:

1. Emptycleaning tank as follows:

a. Disconnecthoseconnectedto injection fitting on

pump. Piaceend of hoseinto suitabie container.

b. Rotatedetergent shut-off valveto "On" position and

open the tanks cover. Gravitywiii empty tank

contents into container.

c. Reconnect hoseto injection fitting on pump. Add

0.5 quart of cleanfresh water to cleaningtank and

ciose tanks cover.

2. Fiush cteaningsystem byturning detergentshut-off

valveto "On" position, rotate PrecisionSprayTM Selector

to a Iowpressure position and run pressure washer.

Flush untii cleaningtank is empty.Turn its detergent

shut-off vaiveto "Off" position.

3. Foliow steps 2-5 in the previous sectionAfter EachUse.

4. Use pump saver,availableat Searsretail item

7174403GS,to treat pump. This minimizesfreeze

damageand iubricates pistons and seals.

5. If pump saver is not avaiiabie, connecta 3-foot section

of garden hoseto water inlet adapter. Pour

RV-antifreeze (antifreezewithout alcohol) into hose. Pull

recoii handletwice. Disconnect3-foot hose.

6. Store unit ina clean,dry area.

LONGTER I STORAGE

If you do not plan to usethe pressure washer for morethan

30 days,you must prepare the engine and pump for long

term storage.

It is important to preventgum deposits from forming in

essentialfuel system parts such asthe carburetor, fuet filter,

fuel hose or tank during storage. Also, experienceindicates

that alcohol-blendedfuels (called gasohol, ethanol or

methanol) canattract moisture, which ieadsto separation

and formation of acids during storage. Acidic gas can

damagethe fuel system of anengine while in storage.

Pretect Fuel System

FuelPre_er:

Fueican becomestab when stored over 30 days.Stab fuel

causesacid and gum depositsto form in the fuei system or

on essentialcarburetor parts. To keepfue! fresh, use Bdggs

& Stratton FRESHSTAR7Mfuel stabiiizer, availableas a

liquid additive or a drip concentrate cartridge.

Thereis no needto draingasoiine from the engineif afuel

stabilizer is added according to instructions. Runthe engine

for 2 minutesto circulate the stabiiizerthroughout the fuel

system. Theengine and fuet can then bestored upto

24 months.

If gasolinein the engine has not beentreated with afuel

stabiiizer, it must be drained into an approved container. Run

the engine untii it stops from iack of fuel. The use of a fuel

stabilizer in the storagecontainer is recommendedto

maintain freshness.

Change (}ira

Whib engine isstiii warm, drain oil from crankcase. Refill

with recommendedgrade. See ChangingE,_gineOil.

Oil Cylinder Bere

* Removespark plug andpour about 1/2 ounce (15 mI) of

cleanengine oii into the cyiinder.

* Instali spark plugand pull starter handle slowly to

distribute oil.

Pretect Pump

To protect the pump from damagecausedby mineral

deposits or freezing, usePumpSaver,item 7174403GS,to

treat pump. This preventsfreezedamageand lubricates

)istons andseals.

You must protect your unit from freezing temperatures.

Failuretodo sowill permanentlydamageyourpurnpand

renderyourunitinoperable.

Freezedamageisnotcoveredunderwarranty.

NOTE:PumpSaveris availabieasan optional accessory.It is

not included with the pressurewasher. Contact your iocaI

Searsservice center to purchase PumpSaver.

To usePumpSaver,makesure the pressurewasher is turned

off anddisconnected from suppiy water. Readand foliow aii

instructions andwarnings given onthe PumpSavercontainer.

ether $terage Tips

1. DONOTstore fuel from one seasonto another unless it

hasbeentreated asdescribed in Protect Fud System.

Repiacefuei container if it starts to rust. Rust and/or dirt

in fuel cancause problems if it's usedwith this unit.

Coverunit with a suitable protectivecover that does not

retain moisture.

WARNING

_ Storagecovers can be flammable=

o DONOTplacea storagecoveroverahotpressurewasher.

• Letequipmentcoo[fora sufficbnttime beforeplacingthe

coverontheequipment.

4. Store unit in acleanand dry area.

Page is loading ...

Craftsman 580.752100 Owner's manual

Brand: Craftsman

Model: 580.752100

Category: High-pressure cleaners

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

español: Craftsman 580.752100 El manual del propietario

Craftsman 580.752100 Owner's manual

This manual is also suitable for

Craftsman 580.752100 Owner's manual

in other languages

Related papers

Other documents