i-onik BTH-033 Owner's manual

Brand: i-onik

Model: BTH-033

Category: Mobile headsets

Type: Owner's manual

This manual is also suitable for

i.onik BTH-033

Headset

BTH-033

Kurzanleitung

Quick Start Guide

Chips and More GmbH

Gewerbestr. 7 | 79112 Freiburg | Germany | www.i-onik.de

Service: + 49 7664 403 69 12

Email: [email protected]

Page is loading ...

20 21

English

Contents

Brief introduction ....................................................... 21

1. Bluetooth Wireless Communication Technology .............. 21

2. About BTH-033 .......................................................... 21

Before use .................................................................. 22

1. Overview .................................................................. 22

2. Charging for Headsets ................................................ 23

Getting started ........................................................... 24

1. Turning the Headset on/off ................................... 24

2. Pairing the Headset with Bluetooth Devices ........... 25

1) How to Enter Pairing Mode ...................................... 25

2) Pairing the Headset with a Bluetooth Mobile Phone .... 25

3) Pairing the Headset with a Bluetooth Transmitter ....... 26

4) Pairing the Headset with Multi-Devices ..................... 27

3. Reconnecting with a Bluetooth Device .................... 27

4. Making Calls with the Headset ................................ 28

5. Playing Music ......................................................... 31

6. LED Indicator ......................................................... 32

7. Indication Tone ...................................................... 33

8. Factory Reset ......................................................... 33

9. Resetting ................................................................ 33

Care and Maintenance ................................................ 33

FAQs ........................................................................... 34

Specication ............................................................... 35

Welcome to this guide on using this Bluetooth stereo headset,

BTH-033. Please read this user’s manual carefully before use.

Brief introduction

1. Bluetooth Wireless Communication Technology

Bluetooth is a standard of close range wireless communication

technology that was drawn up by Sony-Ericsson, IBM, Intel, No-

kia and Toshiba. With Bluetooth technology, we can achieve the

highest transmission rate among mobile phones, computers,

printers, PDAs and other devices. The maximum transmission

range of class II is 10 metres while the maximum transmission

range of class I can reach up to 100 metres.

2. About BTH-033

BTH-033 is a Bluetooth stereo headset. The foldable and

retractable design makes it very easy to take with you. It

supports the following Bluetooth proles:

HSP ........ Headset Prole

HFP ........ Hands-Free Prole

A2DP ...... Advanced Audio Distribution Prole

AVRCP .... Audio/Video Remote Control Prole

You can enjoy music wirelessly by using BTH-033. It has the

following features:

1) Pairing with a Bluetooth mobile phone or PDA supporting HFP

prole

- Answer a call, end a call and reject a call

- Redial last number

- Voice dial

- Adjust the volume

- Call transfer between the headset and your Bluetooth

mobile phone

- Mute microphone

2) Pairing with a Bluetooth music device or Bluetooth

transmitter supporting an A2DP proleEnjoy music wirelessly

- Enjoy music wirelessly

22 23

- Adjust the volume

- Remote control pause/play

- Remote control previous/next track

3) Easy to switch between the call and music, you will not miss

the incoming call during listening to music.

4) Every time the headset is turned on, it will connect to last

connected device automatically.

Note: In order to complete above function, the Bluetooth

proles of paired device must be the same as the headset. And

even though the paired device and the headset support the

same Bluetooth proles, functions may vary due to specication

differences of the paired devices.

Before Use

1. Overview

2. Charging the Headset

The headset comes with a built-in rechargeable battery. Prior to

using it, it is recommended that you charge the battery fully for

the rst time.

When the headset’s power is low, the red LED indicator ashes

twice and the headset emits three “dong” sounds every

30 seconds. You need to recharge the battery of the headset.

1 Built-in microphone 7 LED indicator

2 Multi-function

button(MFB)

8 Charging jack

3 Next song 9 Volume down

4 Pause/play 10 Volume up

5 Last song 11 Right speaker

6 Line-in jack 12 Left speaker

24 25

The charging procedure is as follows:

Using a USB cable

1. Plug USB charging cable into the USB port of the computer

2. Plug the other end of the USB cable into the headset.

Red light on: Charging

Red light off: Finish charging

3. It will take about 2.5 hours to complete the charging.

2. Pairing the Headset with Bluetooth Devices

1) How to enter Pairing Mode

Note:

1) The battery is recyclable.

2) Batteries (the battery pack or batteries installed) must not

be exposed to excessive heat, such as in the sunshine or

near to a re.

Getting started

1. Turning the headset on/off

Note:

Pairing mode will last 2 minutes. If no devices can be connected

after 2 minutes, it will return to standby mode automatically.

2) Pairing the Headset with a Bluetooth Mobile Phone

Prior to using the headset for the rst time, you have to pair

it with a Bluetooth-enabled mobile phone. The pairing proce-

dure will vary with different models of mobile phones. Refer

to your mobile phone user’s manual for further information.

The general pairing procedure is as follows:

1) Keep your headset and phone within 1 metre when

pairing.

2) Make the headset enter pairing mode (please refer to

“How to enter pairing mode˝).

3) Activate your cell phone’s Bluetooth function and set your

cell phone to search for Bluetooth devices within range,

and select “i.onik BTH-033” from the list of devices shown.

4) According to the indication, enter password or PIN

number: “0000”.

5) If prompted by your mobile phone to connect, select “Yes”

(this will vary depending on the mobile phone being used).

6) After successful connecting, the blue LED indicator ashes

twice every 4 seconds or ashes 3 times every 4 seconds.

Note:

In order to save power, the headset will turn off automatically

after 5 minutes if no devices are connected.

Functions Operation LED indicator

Turning on Press and hold

MFB button for

3-5 seconds until

blue LED indicator

ashes.

Blue LED indicator

on for one second.

Turning off Press and hold

MFB button for

3 seconds until

red LED indicator

ashes.

Red LED indicator

on for one second.

Functions Operation LED indicator

Entering pairing

mode

Ensure the head-

set is off, and then

press and hold

MFB button for 7-8

seconds until red

and blue LED ash

alternately

Red and blue LED

ash alternately

26 27

Note:

- If pairing fails, please turn off the headset rst and then

repair according to steps 1-6 above.

- Once pairing is successful, the headset and the mobile phone

will remember each other; there will be no need to repair

next time. The headset can remember 8 paired devices. When

the number of paired devices exceeds 8, the rst one will be

replaced.

- Every time the headset is turned on, it will connect to the

last connected device automatically. If you want to pair it

with other devices, turn off the Bluetooth function of the last

connected device then pair the headset with the new device,

following steps 1-6 above.

3) Pairing the Headset with a Bluetooth Transmitter

You can connect the headset to a Bluetooth transmitter, to

enjoy music wirelessly. Take a BTT010 (Bluetooth transmit-

ter for iPod and iPhone - not included), for example. The

pairing steps are as follows:

1) Keep your headset and phone within 1 metre when

pairing.

2) Set the headset to enter pairing mode (refer to “How to

enter pairing mode”).

3) Turn on the Bluetooth transmitter. It will search for Blue-

tooth devices automatically and send a pairing request.

4) When the headset requests you to enter a PIN number,

the transmitter will respond “0000” automatically.

5) After successful pairing and connecting, the blue LED

indicator on the headset ashes twice every 4 seconds.

Note:

- The pairing password of the headset is “0000”. The headset

can, therefore, only pair with a Bluetooth transmitter whose

pairing password is “0000”.

- If pairing still fails after several tries, refer to the Bluetooth

transmitter user’s manual for further information.

4) Multi-pairing

The headset can connect with two devices at most. One is a

Bluetooth mobile phone supporting a HFP prole; the other

one is a Bluetooth music device supporting an A2DP prole.

If you want to nish the multi-pairing, proceed as follows:

1) Firstly, pair the headset with a Bluetooth transmitter

(refer to “Pairing the headset with a Bluetooth trans-

mitter”).

2) Turn off the Bluetooth transmitter.

3) Pair and connect the headset with a Bluetooth mobile

phone (refer to “Pairing the headset with a Bluetooth

mobile phone”).

4) Turn on the Bluetooth transmitter; it will connect to the

headset automatically.

Note:

- After successful multi-pairing, the paired devices will remem-

ber each other. You will not need to pair next time. If the

pairing information is deleted, connect the mobile phone with

the headset and then turn on the Bluetooth transmitter. Multi-

connecting can be performed.

- For a mobile phone supporting the HSP and A2DP at the same

time, you may set up a HSP and A2DP connection with the

headset simultaneously. At this time, the Bluetooth transmit-

ter must not be connected to the headset.

3. Reconnecting with a Bluetooth Device

1) Automatic connecting

Every time the headset is turned on, it will connect to the

last connected device automatically.

BTT010

(Fig. similar.

Not included.)

28 29

2) Manual connecting

When the headset is in standby mode and doesn’t connect

to a device, short press MFB button once and it will connect

to the last connected device.

Note:

- Before connecting to a Bluetooth device, turn on the Blue-

tooth function of the Bluetooth device.

- On some Bluetooth devices - some Nokia mobile phones,

for example - you have to allow automatic connecting in the

mobile phone’s settings. Refer to your mobile phone’s manual

for further information

4. Making a call with the headset

1) Basic operation

Functions Operation LED indicator

Cancel a call Calling Short press MFB

once

Answer a call Incoming ringing Short press MFB

once

Reject a call Incoming ringing Long press MFB

for 2 seconds and

release it until

listen a tone

End a call During a call Short press MFB

once

Volume up During a call Short press +

button

Volume down During a call Short press —

button

Transfer conver-

sation to mobile

phone

During a call Long press MFB

for 2 seconds

Transfer conver-

sation to headset

During a call Long press MFB

for 2 seconds

Mute microphone During a call Double click MFB

Cancel mute During a call

(microphone

mute)

Double click MFB

Voice dial Standby mode

(connected device)

Long press

button for

2 seconds

Redial the last

number

Standby mode

(connected device)

Double click MFB

Remove paired list Turned off Press MFB and

pause button for

8 seconds simul-

taneously, and

release it until the

red and blue (or

purple) LED are on

at the same time

30 31

2) Three-Ways Call Operation 5. Playing Music

When the headset connects to a mobile phone or Bluetooth

transmitter which supports A2DP, you can enjoy music

wirelessly through the headset.

Notes:

- When playing music on some mobile phones, the music will

be transmitted to the mobile phone’s speaker instead of the

headset. You have to select “Transmit the sound via Blue-

tooth” in the settings menu and then choose “BTH-033” as the

speaker device. The music will be transmitted to the headset.

Refer to your mobile phone user’s manual for further informa-

tion.

- When the volume is adjusted to maximum or minimum, you

will hear one prompt tone.

WARNING:

Excessive pressure from earphones and headphones can cause

hearing loss.

Note:

- Not all the mobile phones support all the functions listed

above. Refer to your mobile phone user’s manual.

- Function and prompt tones will differ, depending on the

mobile phone.

- When the volume is adjusted to maximum or minimum, you

will hear one prompt tone.

- When pressing the answer button on some mobile phones,

the call will be transferred to the mobile phone. You can

switch the call to the headset by using the conversation

switch button or through operating it on the mobile phone.

Refer to your mobile phone user’s manual for further infor-

mation.

Functions Operation LED indicator

Answer new call

and end current

call

There is a second

incoming call

Shortly press MFB

once

Answer new call

and retain current

call

There is a second

incoming call

Long press MFB

for 2 seconds

Switch calls Keep conversation Long press MFB

for 2 seconds

End current call

and switch retain

call

Keep conversation Shortly press MFB

once

Functions Operation LED indicator

Volume up Playing music Shortly press “+”

button

Volume down Playing music Shortly press “―”

button

Last song Playing music

Shortly press 

button once

Next song Playing music

Shortly press 

button once

Pause Playing music

Shortly press ||

button once

Play Pausing

Shortly press ||

button once

Line in input Turned off It can play music

through aq 3.5 mm

audio line

32 33

- If you want to remotely select the last/next song, or pause/

play, it needs your Bluetooth mobile phone or Bluetooth

transmitter need to be paired with the headset to support

the AVRCP prole. Refer to the user’s manual of your mobile

phone or Bluetooth transmitter for further information.

- The Bluetooth will disconnect the headset and the mobile

phone automatically if you plug in 3.5 mm audio input, and

the line in is available at the time.

6. LED Indicator

1) Charging

7. Indication Tone

8. Factory Reset

In the status of turned off, long press MFB and pause buttons

for 8 seconds simultaneously and don’t release them until the

red and blue LED indicators are on.

9. Resetting

If the product works abnormally, you can plug a 3.5 mm Line-in

or charge the headset so that it resets the product.

Care and Maintenance

Read the recommendations below carefully before using the

“BTH-033”. By following these you will be able to enjoy this

product for many years.

- Keep it dry and don’t put it in a dump place, to avoid the

product’s internal circuit being affected.

- Keep the product away from direct sunlight or hot places.

High temperatures will shorten the life of electronic devices,

destroy the battery or distort certain plastic parts.

- Don’t expose the product to cold areas. It may damage the

internal circuit board.

- Don’t try to disassemble the product as it may get damaged.

- Don’t let it fall down on to the oor or on other hard surfaces.

The internal circuit might get damaged.

2) Pairing with Bluetooth Device

LED indicator Status of headset

Red LED on Charging

Red LED off Finished charging

LED indicator Status of headset

Red and blue LED indicator

ashes alternately

Pairing mode

Blue LED indicator ashes

once quickly every 2 seconds

Not connected device

Blue LED indicator ashes

twice quickly every 4 seconds

Have already connected HFP

or A2DP

Blue LED indicator ashes

three times quickly every

4 seconds

Connect HFP and A2DP

simultaneously

Blue LED indicator ashes

quickly

Calling/incoming call

Blue LED indicator ashes

once quickly every 4 seconds

During a call

Indication tone Status of the headset

Continuous two prompt tone

every 10 seconds

Conversation mode and

microphone mute

Three ‘dong’ warning sounds

every 30 seconds

Low battery

Blue LED indicator ashes

once quickly every 4 seconds

Low battery

34 35

- Don’t use intensive chemical products or detergents to clean

the product.

- Don’t scratch the surface with sharp things.

If the product doesn’t function properly, return it to the store

from which you bought it. The staff will help you to solve the

problem.

FAQs

1. What does it mean when red LED blinks twice every

30 seconds?

The battery is low and needs to be recharged.

2. Why is the red LED off when charging?

a) Make sure that the charging device is well connected to

the headset.

b) If you don’t use the headset for a long time, the

battery may dry up. If this happens, you have to

charge the battery for 30 minutes, and then the red

LED indicator should be ON.

3. How far is the effective range between the headset

and mobile phone?

According to the Bluetooth standard, the maximum

available range of a Class II headset is 10 metres.

It varies under different environments.

4. Why can’t my mobile phone search and nd the

headset?

The mobile phone will not nd the headset if the headset

and mobile phone are not under the pairing mode. Make

sure that the headset is under the pairing mode and in the

effective working range; then the headset can be paired and

connected.

5. Why can’t I hear the voice?

a) Make sure the headset has been switched on.

b) Make sure the volume is not too low or muted.

c) Make sure that the headset is connected with the mobile

phone correctly.

d) Make sure that the distance between the headset and the

mobile phone is in the available Bluetooth range.

6. Why is the voice not clear during a conversation?

a) Make sure that the mobile phone is in a strong signal

area.

b) Make sure that the headset is in the available range for

this product.

7. Why can’t I control pause, play, last song and next

song when playing music?

This function needs a Bluetooth device supporting AVRCP

(Audio/Video Remote Control Prole).

Specications

Bluetooth version Bluetooth V2.1+EDR

Bluetooth proles Headset, Hands free, A2DP,

AVRCP

Operating distance 10 meters

Headset working time Music up to 15 hours

Headset standby time Approx 384 hours

Charging input DC5.0V 340 mA

Headset charging time About 3 hours

Dimension 176 x 165 x 32 mm

Weight Approx 177 g

Battery capacity 430 mAH

36 37

Notes:

1. This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) this device

must not cause harmful interference; and (2) this device

must accept any interference received, including interference

that may cause undesired operation.

2. Changes or modications not expressly approved by the

party responsible for compliance could void the user’s

authority to operate the equipment.

Page is loading ...

i-onik BTH-033 Owner's manual

Brand: i-onik

Model: BTH-033

Category: Mobile headsets

Type: Owner's manual

This manual is also suitable for

i.onik BTH-033

Download PDF

report

in other languages

Deutsch: i-onik BTH-033 Bedienungsanleitung

i-onik BTH-033 Owner's manual

This manual is also suitable for

i-onik BTH-033 Owner's manual

in other languages

Related papers

Other documents