Makita JR180D User manual

GB

Cordless Recipro Saw Instruction Manual

F

Scie recipro sans fil Manuel d’instructions

D

Akku-Reciprosäge Betriebsanleitung

I

Seghetto alternativo a batteria Istruzioni per l’uso

NL

Accu-reciprozaag Gebruiksaanwijzing

E

Sierra de sable a batería Manual de instrucciones

P

Serra de sabre a bateria Manual de instruções

DK

Akku bajonetsav Brugsanvisning

S

Sladdlös tigersåg Bruksanvisning

N

Batteridrevet bajonettsag Bruksanvisning

SF

Akkukäyttöinen puukkosaha Käyttöohje

GR Ασύρµατ' παλινδρ'µικ. πρι.νι /δηγίες 5ρήσεως

JR180D

Page is loading ...

4

ENGLISH

Explanation of general view

1 Battery cartridge

2Push button

3 Released position

4Fixed position

5 Blade clamp sleeve

6Blade

7Lever

8Shoe

9 Switch trigger

10 Lock-off button

11 Press in

12 Limit mark

13 Screwdriver

14 Brush holder cap

SPECIFICATIONS

Model JR180D

Length of stroke .................................................... 23 mm

Strokes per minute ........................................... 0 – 2,700

Cutting capacities

Pipe ................................................................... 90 mm

Wood ................................................................. 90 mm

Overall length ..................................................... 469 mm

Net weight (with battery cartridge) ........................ 3.5 kg

Rated voltage ...................................................D.C. 18 V

•Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for sawing wood, plastic and ferrous

materials.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

IMPORTANT SAFETY INSTRUCTIONS FOR

CHARGER & BATTERY CARTRIDGE

ENC004-1

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using bat-

tery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Always cover the battery terminals with the bat-

tery cover when the battery cartridge is not

used.

6. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

7. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

8. Do not incinerate the battery cartridge even if it

is severely damaged or is completely worn out.

The battery cartridge can explode in a fire.

9. Be careful not to drop or strike battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the bat-

tery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-

tery cartridge cool down before charging it.

4. Charge the Nickel Metal Hydride battery car-

tridge when you do not use it for more than six

months.

SPECIFIC SAFETY RULES

GEB008-2

DO NOT let comfort or familiarity with product

(gained from repeated use) replace strict adher-

ence to recipro saw safety rules. If you use this

tool unsafely or incorrectly, you can suffer seri-

ous personal injury.

1. Hold power tools by insulated gripping sur-

faces when performing an operation where

the cutting tool may contact hidden wiring or

its own cord.

Contact with a "live" wire will make

exposed metal parts of the tool "live" and shock the

operator.

2. Use clamps or another practical way to

secure and support the workpiece to a stable

platform.

Holding the work by hand or against your

body leaves it unstable and may lead to loss of con-

trol.

3. Always use safety glasses or goggles. Ordi-

nary eye or sun glasses are NOT safety

glasses.

4. Avoid cutting nails. Inspect workpiece for any

nails and remove them before operation.

5. Do not cut oversize workpiece.

6. Check for the proper clearance beyond the

workpiece before cutting so that the blade

will not strike the floor, workbench, etc.

7. Hold the tool firmly.

8. Make sure the blade is not contacting the

workpiece before the switch is turned on.

9. Keep hands away from moving parts.

10. Do not leave the tool running. Operate the

tool only when hand-held.

5

11. Always switch off and wait for the blade to

come to a complete stop before removing the

blade from the workpiece.

12. Do not touch the blade or the workpiece

immediately after operation; they may be

extremely hot and could burn your skin.

13. Do not operate the tool at no-load unneces-

sarily.

14. Always use the correct dust mask/respirator

for the material and application you are work-

ing with.

15. Some material contains chemicals which may

be toxic. Take caution to prevent dust inhala-

tion and skin contact. Follow material sup-

plier safety data.

SAVE THESE INSTRUCTIONS.

WARNING:

MISUSE or failure to follow the safety rules stated

in this instruction manual may cause serious

personal injury.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig. 3)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while pressing the push buttons on both sides of

the cartridge.

•To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

•Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Installing or removing saw blade

CAUTION:

• Always clean out all chips or foreign matter adhering to

the blade, blade clamp and/or slider. Failure to do so

may cause insufficient tightening of the blade, resulting

in a serious injury.

To i n s t a l l t h e s a w b l a d e , a l w a y s m a k e s u r e t h a t t h e b l a d e

clamp sleeve is in released position before inserting the

saw blade. If the blade clamp sleeve is in fixed position,

rotate the sleeve to the released position. (Fig. 4)

Insert the saw blade into the blade clamp as far as it will

go. The blade clamp sleeve rotates and the saw blade is

fixed. Make sure that the saw blade cannot be extracted

even though you try to pull it out. (Fig. 5)

NOTE:

If you do not insert the saw blade deep enough, the saw

blade may be ejected unexpectedly during operation.

This can be extremely dangerous.

To r e m o v e t h e s a w b l a d e , r o t a t e t h e b l a d e c l a m p s l e e ve

in the direction of the arrow fully. The saw blade is

removed and the blade clamp sleeve is fixed at the

released position. (Fig. 6)

NOTE:

If you remove the saw blade without rotating the blade

clamp sleeve fully, the sleeve may not be fixed. In this

case, rotate the blade clamp sleeve fully to make the

sleeve fixed at the released position.

Adjusting the shoe (Fig. 7)

When the blade loses its cutting efficiency in one place

along its cutting edge, reposition the shoe to utilize a

sharp, unused portion of its cutting edge. This will help to

lengthen the life of the blade. To reposition the shoe,

loosen the lever and slide the shoe forward or back to the

desired position. Then tighten the lever to firmly secure

the shoe.

Switch action (Fig. 8)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the “OFF” position when released.

To p r e v e n t t h e t r i g g e r f r o m b e i n g a c c i d e n t a l l y p u l l e d , a

lock-off button is provided. To start the tool, press in the

lock-off button and pull the trigger. The lock-off button

can be pressed in from either left or right side of the tool.

Tool speed is increased by increasing pressure on the

trigger. Release the trigger to stop.

Operation (Fig. 9)

Press the shoe firmly against the workpiece. Do not allow

the tool to bounce. Bring the blade into light contact with

the workpiece. First, make a pilot groove, using a slower

speed. Then use a faster speed to continue cutting.

CAUTION:

•Always use a suitable coolant (cutting oil) when cutting

metal. Failure to do so will cause premature blade

wear.

• Always wear gloves to protect your hands from hot fly-

ing chips when cutting metal.

• Always press the shoe firmly against the workpiece

during operation. If the shoe is held away from the

workpiece during operation, strong vibration and/or

twisting will be produced, causing the blade to snap

dangerously.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work on

the tool.

Replacement of carbon brushes (Fig. 10 & 11)

Replace carbon brushes when they are worn down to the

limit mark. Both identical carbon brushes should be

replaced at the same time.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Center.

6

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita service center.

• Recipro saw blade

•Plastic carrying case

•Various type of Makita genuine batteries and chargers

• Battery cover

Page is loading ...

37

ENH102-4

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product

is in compliance with the following standards of standard-

ized documents,

EN60745, EN55014

in accordance with Council Directives, 89/336/EEC and

98/37/EC.

DÉCLARATION DE CONFORMITÉ CE

Nous déclarons sous notre entière responsabilité que ce

produit est conforme aux normes des documents stan-

dardisés suivants,

EN60745, EN55014

conformément aux Directives du Conseil, 89/336/CEE et

98/37/EG.

CE-KONFORMITÄTSERKLÄRUNG

Hiermit erklärt wir unter unserer alleinigen Verantwor-

tung, daß dieses Produkt gemäß den Ratsdirektiven

89/336/EWG und 98/37/EG mit den folgenden Normen

von Normendokumenten übereinstimmen:

EN60745, EN55014.

DICHIARAZIONE DI CONFORMITÀ

CON LE NORME DELLA COMUNITÀ EUROPEA

Dichiariamo sotto la nostra sola responsabilità che

questo prodotto è conforme agli standard di documenti

standardizzati seguenti:

EN60745, EN55014

secondo le direttive del Consiglio 89/336/CEE e

98/37/CE.

EG-VERKLARING VAN CONFORMITEIT

Wij verklaren hierbij uitsluitend op eigen verant-

woordelijkheid dat dit produkt voldoet aan de volgende

normen van genormaliseerde documenten,

EN60745, EN55014

in overeenstemming met de richtlijnen van de Raad

89/336/EEC en 98/37/EC.

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra sola responsabilidad que este

producto cumple con las siguientes normas de docu-

mentos normalizados,

EN60745, EN55014

de acuerdo con las directivas comunitarias, 89/336/EEC

y 98/37/CE.

Yasuhiko Kanzaki

CE 2005

Director Amministratore

Directeur Directeur

Direktor Director

MAKITA INTERNATIONAL EUROPE LTD.

Michigan Drive, Tongwell, Milton Keynes,

Bucks MK15 8JD, ENGLAND

Responsible manufacturer: Produttore responsabile:

Fabricant responsable

:

Verantwoordelijke fabrikant:

Verantwortlicher Hersteller: Fabricante responsable:

Makita Corporation Anjo Aichi Japan

ENGLISH

FRANÇAISE

DEUTSCH

ITALIANO

NEDERLANDS

ESPAÑOL

Page is loading ...

39

ENG004-2-V3

For European countries only

Noise and Vibration

The typical A-weighted sound pressure level is 81 dB (A).

Uncertainty is 3 dB (A).

The noise level under working may exceed 85 dB (A).

– Wear ear protection. –

The typical weighted root mean square acceleration

value is 14 m/s

2

.

These values have been obtained according to

EN60745.

Pour les pays d’Europe uniquement

Bruit et vibrations

Le niveau de pression sonore pondere type A est de

81 dB (A).

L’incertitude de mesure est de 3 dB (A).

Le niveau de bruit en fonctionnement peut dépasser

85 dB (A).

– Porter des protecteurs anti-bruit. –

L’accélération pondérée est de 14 m/s

2

.

Ces valeurs ont été obtenues selon EN60745.

Nur für europäische Länder

Geräusch- und Vibrationsentwicklung

Der typische A-bewertete Schalldruckpegel beträgt

81 dB (A).

Die Abweichung beträgt 3 dB (A).

Der Lärmpegel kann während des Betriebs 85 dB (A)

überschreiten.

– Gehörschutz tragen. –

Der gewichtete Effektivwert der Beschleunigung beträgt

14 m/s

2

.

Diese Werte wurden gemäß EN60745 erhalten.

Modello per l’Europa soltanto

Rumore e vibrazione

Il livello di pressione sonora pesata secondo la curva A è

di 81 dB (A).

L’incertezza è di 3 dB (A).

Il livello di rumore durante il lavoro potrebbe superare gli

85 dB (A).

– Indossare i paraorecchi. –

Il valore quadratico medio di accellerazione è di 14 m/s

2

.

Questi valori sono stati ottenuti in conformità EN60745.

Alleen voor Europese landen

Geluidsniveau en trilling

Het typische A-gewogen geluidsdrukniveau is 81 dB (A).

Onzekerheid is 3 dB (A).

Tijdens het werken kan het geluidsniveau 85 dB (A) over-

schrijden.

– Draag oorbeschermers. –

De typische gewogen effectieve versnellingswaarde is

14 m/s

2

.

Deze waarden werden verkregen in overeenstemming

met EN60745.

Para países europeos solamente

Ruido y vibración

El nivel de presión sonora ponderada A es de 81 dB (A).

Incerteza 3 dB (A).

El nivel de ruido en condiciones de trabajo puede que

sobrepase los 85 dB (A).

– Póngase protectores en los oídos. –

El valor ponderado de la aceleración es de 14 m/s

2

.

Estos valores han sido obtenidos de acuerdo con

EN60745.

ENGLISH

FRANÇAISE

DEUTSCH

ITALIANO

NEDERLANDS

ESPAÑOL

Page is loading ...

Makita JR180D User manual

Makita JR180D User manual

in other languages

Related papers

Other documents