Philips XX-VR150/58 User manual

Philips
Brand
Philips
Model
XX-VR150/58
Category
Cassette players
Type
User manual

This manual is also suitable for

This video recorder is used for the recording and playback of VHS videocassettes.
Cassettes with the VHS-C label (VHS cassettes for camcorders) may only be used
with a suitable adapter.
We hope you enjoy your new video recorder.
EN
Thank you for buying a Philips video recorder. This video recorder is one of the most sophisticated and easy-
to-use video recorders (VCR) on the market. Please take the time to read this operating manual before using
your video recorder. It contains important information and notes regarding operation. The video recorder
should not be turned on immediately after transportation from a cold to a hot area or vice versa, or in con-
ditions of extreme humidity. Wait at least three hours after transporting the device. The video recorder needs
this time in order to become acclimatised to its new environment (temperature, air humidity, etc.).
VR150/58
0VMN03970
HG273ED*****
PAL
Important notes regarding operation
Danger: High voltage!
Do not remove the top cover as there is
a risk of an electrical shock!
To reduce the risk of fire or electric shock, do
not expose this device to rain or moisture.
The video recorder does not contain any
components that can be repaired by the
customer. Please leave all maintenance
work for qualified personnel.
As soon as the video recorder is connected
to the power supply, there are some compo-
nents that are in constant operation. To
switch off the video recorder completely you
must disconnect it from the power supply.
Make sure that air can circulate freely through
the ventilation slots on the video recorder. Do
not place the device on an unsteady base.
Make sure that no objects or liquids enter
the video recorder. Do not place vases or
the like on the video recorder. If liquid is
spilt into it, immediately disconnect the
video recorder from the power supply and
call After-sales Service for advice.
Do not place any combustible objects on
the device (candles, etc.).
Make sure that children do not place any
foreign objects within the openings or venti-
lation slots.
These operating instructions have been
printed on non-polluting paper.
Deposit old batteries at the appropriate col-
lection points.
Please make use of the facilities available in
your country for disposing of the packaging
of the video recorder in a way that helps to
protect the environment.
This electronic device contains many mate-
rials that can be recycled. Please enquire
about the possibilities for recycling your old
device.
So that you can identify your machine for service
questions or in the event of theft, enter the serial
number here. The serial number (PROD.NO.) is
printed on the type plate fixed at the back of the
device.
This product complies with the requirements of
Directive 73/23/EEC +89/336/EEC +93/68 EEC.
Specifications
Voltage: 220-240V/50Hz
Power consumption : 14W
Power consumption (Standby): less than 3W
Rewind time: 260 seconds (cassette E-180)
Dimensions in cm (WxDxH): 36.0x22.6x9.2
Number of video heads : 2
Recording/playback time:
3 hours (SP) (cassette E-180)
6 hours (LP) (cassette E-180)
Supplied accessories
• Operating instructions
• Remote control and 2 batteries
• Aerial Cable
MODEL NO. VR150/58
PROD. NO. ...........................
!
!
!
!
"
"
"
1
"
HG273ED(EN).qx3 04.2.3 10:54 AM Page 1
2
EN
1. Description of controls
1 2 3
4 5 6
7 8 9
0
STILL
STOP
MENU
REW FWD
PLAYSTATUS/EXIT CLEAR
REC STANDBY/ON
TV-PROG.TV-VOL
MUTE SYSTEM
PP
STANDBY/ON PROGRAMME RECORD STOP/EJECT REW. PLAY FWD.
RF OUT
TV
AERIAL
The remote control
Buttons for VCR feature only
To record the TV channel selected at this
moment.
To switch off or on, interrupt menu
function.
Press to select channels at VCR.
To select the programme number. During
playback, press to adjust the tracking.
To access or remove the VCR’s on-
screen status display. To exit on-screen menus.
To delete last entry. To clear a programmed
recording (TIMER). To reset the elapsed time counter in
the playback, recording or stop mode.
To stop the tape and play back a picture
step by step. (except for during fast forwarding and fast
rewinding)
To change video (colour) system.
To call up main menu of VCR.
When tape playback is stopped, press to
fast forward the tape at high speed. During playback,
press to fast forward the tape while the picture stays on
the screen. To store or confirm entry in the menu.
When tape playback is stopped, press to
rewind the tape at high speed. During playback, press
to rewind the tape while the picture stays on the
screen.To return the cursor in the menu.
To play back a tape, select an item in
the menu of VCR.
To stop the tape, select an item in the
menu of VCR.
Buttons with TV feature
To eliminate the TV’s sound. Press again to
restore the volume.
To adjust the TV’s
volume.
To select a programme
number on the TV.
TV-PROG.
–
TV-PROG.
+
TV-VOL5
–
TV-VOL5
+
MUTE
STOP
C
-
L
PLAY
B- K
REW
0- s
FWD
1- B
MENU
SYSTEM
STILL
2
CLEAR
STATUS/EXIT
P–P
+
0..9
STANDBY/ON
yy
REC
I
You can use this remote control to operate some functions of Philips TVs.
HG273ED(EN).qx3 04.2.3 10:54 AM Page 2
3
EN
2. Important notes for operation
Navigation in the screen menu
You can check/change many functions and set-
tings of your video recorder via the on-screen
menu. The individual functions are selected, via
the remote control as follows:
Call up the menu: with .
To select: with .
To enter or change your selection: with the
number buttons or with .
To save or confirm: with .
To cancel: with .
To end: with .
The symbols on your video recorder
display
These symbols can light up on your video
recorder display:
When you keep your video recorder on.
When you have put a cassette in the video
recorder.
Display of programme number of the TV
channel / time / RF channel.
When you record.
When you have programmed a recording.
STATUS/EXIT
CLEAR
FWD 1- B
STOP C-LPLAY B-K
0..9
STOP C-LPLAY B-K
MENU
SELECT KL CHOOSE B
→TIMER
RECORD SET UP
VCR SET UP
TUNER SET UP
INITIAL SET UP
END=EXIT
Front of your VCR
To switch off or on, interrupt menu
function.
To select the
programme number. During playback, press to adjust
the tracking.
To record the TV channel selected at this
moment.
When tape playback is stopped, press to fast forward
the tape at high speed. During playback, press to fast
forward the tape while the picture stays on the screen.
When tape playback is stopped, press to rewind the
tape at high speed. During playback, press to rewind
the tape while the picture stays on the screen.
To play back a tape.
To stop the tape and eject the
cassette.
Back of your VCR
To connect the TV.
To connect the aerial cable.
To connect the TV.
RF OUT
AERIAL
TV
STOP/EJECT
PLAY
REW.
FWD.
RECORD
PROGRAMME-PROGRAMME+
STANDBY/ON
yy
Switching on
You can switch on the video recorder with the button.
Automatic switch-off
If the video recorder is not used for several minutes, it switches itself off automatically. This function
can be deactivated (e.g. if you want to use the video recorder as a TV receiver). For more
information, please read the section 'Automatic switch-off' in chapter 'Other functions'.
Time in the display
If you have switched the video recorder off with , the time will show in the display, e.g.
'18:00'.
If the clock has not been set, ' --:-- ' will appear.
Power consumption
The video recorder should always be connected to the mains so as not to affect the use of the TV or
programmed recordings.
If the display has been switched off, your video recorder consumes less than 3W in stand-by.
Power outage/no power
Channel information remains saved for up to 1 year, the time and timer information is saved for up to
1 minute.
STANDBY/ON
yy
STANDBY/ON
yy
HG273ED(EN).qx3 04.2.3 10:54 AM Page 3
Preparing the remote control for
operation
The remote control and its batteries are packed
separately in the original video recorder packag-
ing. You must install the batteries in the remote
control before use.
1.
1.Take the remote control and the enclosed
batteries (2 batteries).
2.
2.Open the remote control's battery compart-
ment and place the batteries in it as shown in
the picture and close the battery compart-
ment.
The remote control is now ready to use. Its
range is approximately 7 metres.
Connecting your video recorder to
the TV
The necessary cable connec-
tions must be made before
you can record or playback
TV programmes using your
video recorder.
We recommend that you use a scart cable to con-
nect your TV and video recorder.
Connecting with a scart cable
Have the following
cables ready:
an aerial cable (1, sup-
plied), a scart cable (2,
not supplied).
1.
1.Remove the aerial
cable plug from your
TV. Insert it into the
AERIAL at the back
of the video recorder.
2.
2.Insert one end of the
supplied aerial cable
into the RF OUT at
the back of the video
recorder and the
other end into the
aerial input socket at the back of the TV.
3.
3.Plug one end of a
scart cable into the
scart socket ‘TV’ at
the back of the video
recorder and the other end into the suitable
scart socket on your TV reserved for the
video recorder operation (see your TV's oper-
ating instructions).
4.
4.Switch on the TV.
5.
5.Insert AC cable into the wall socket.
EN
3. Connecting the video recorder
What is a scart cable?
The scart or Euro AV cable serves as the uni-
versal connector for picture, sound and control
signals. With this type of connection, there is
practically no loss of quality during the picture
or sound transfer.
AERIAL
R
F
O
U
T
A
E
R
I
A
L
TV
RF OUT
R
F
O
U
T
A
E
R
I
A
L
TV
TV
R
F
O
U
T
A
E
R
I
A
L
TV
12
My TV has several scart sockets. Which one
should I use?
Select that scart socket which is suited for the
video output as well as for the video input.
My TV has a configuration menu for the
scart socket.
Please configure this scart socket as input-
Output.
4
HG273ED(EN).qx3 04.2.3 10:54 AM Page 4
EN
6.
6.If the connection was properly made and
your TV was automatically switched to the
programme number for the scart socket, you
will see the following picture:
Then, read the section 'Preparation for use' in
the chapter 'Installing your video recorder'.
Connecting without a scart cable
Have an aerial cable (supplied) ready.
1.
1.Switch off your TV.
2.
2.Remove the aerial
cable plug from the
aerial input socket of
the TV. Insert it into
the AERIAL at the
back of the video
recorder.
3.
3.Insert one end of the
supplied aerial cable
into the RF OUT at
the back of the video
recorder and the
other end into the
aerial input socket at the back of the TV.
4.
4.Insert AC cable into the wall socket.
5.
5.Switch on your TV and select the programme
number used for video playback on your TV
(see your TV's operating instructions).
6.
6.Start the TV's channel search manually as if
you wanted to save a new TV channel until
the next screen appears (see your TV's oper-
ating instructions)
.
7.
7.Save this programme number setting on your
TV for video recorder operation.
Then, read the section 'Preparation for use' in
the chapter 'Installing your video recorder'.
My screen is empty
• Many TVs are switched to the programme
number for the scart socket by way of a con-
trol signal sent through the scart cable.
• If the TV does not automatically switch to the
scart socket programme number, manually
change to the corresponding programme
number on your TV (see your TV's operating
instructions).
AERIAL
R
F
O
U
T
A
E
R
I
A
L
TV
RF OUT
R
F
O
U
T
A
E
R
I
A
L
TV
I do not see a Language setting picture
• Check the cable connections.
• Repeat the channel search on your TV.
Programme number for video recorder oper-
ation
You have now saved a programme number for
use by your video recorder as you would a reg-
ular TV channel. This programme number must
now be used in future for video recorder play-
back ('video recorder' TV channel).
5
PUSH MENU TO CONTINUE
PUSH MENU TO CONTINUE
HG273ED(EN).qx3 04.2.3 10:54 AM Page 5
Preparation for use
This chapter shows you how to prepare the video
recorder for use. The video recorder automatically
seeks out and stores all available TV channels.
1.
1.Select the desired language for the on-screen
menu by pressing or .
2.
2.Press .
3.
3.Confirm with .
The automatic TV channel search starts.
4.
4.The clock setting display appears on the TV
screen.
5.
5.Set the time with the number buttons .
6.
6.Set 'DAY', 'MONTH' and 'YEAR' with the
number buttons .
7.
7.When all information is correct, save by
pressing .
The preparation for use is now complete.
Manual TV channel search
In some cases it can occur that all of the TV chan-
nels are not found and saved during the first instal-
lation. In this case, the missing or coded TV chan-
nels must be searched for and stored manually.
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press .The main menu will appear.
3.
3.Use or to select 'TUNER
SET UP'. Then press .
4.
4.Use or to select 'MANU-
AL TUNING'. Then press .
5.
5.Select 'PROG.' with or
.
Then press
.
6.
6.With or
or
, select
the desired programme number that you want
to use for the TV channel, e.g. 'P01'. Then
press .
7.
7.Select 'CHANNEL' with or ,
and confirm with . Then enter the
desired channel with
.
If you set
'
SKIP
'
on for a channel, this chan-
nel will be ignored when going through the
channels with or .
8.
8.Save the TV channel with .
9.
9.To search for other TV channels, begin again
at step 5.
10.
10.To end, press
.
STATUS/EXIT
FWD 1- B
P–
P
+
0..9
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
0..9
STOP C-LPLAY B-K
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
STOP C-LPLAY B-K
MENU
STATUS/EXIT
0..9
0..9
P+
MENU
STOP C-LPLAY B-K
EN
'Aim' correctly
In the following sections, you require the remote
control for the first time. When using, always
aim the front of the remote control at the video
recorder and not at the TV.
Connecting additional devices
After you have connected additional devices
(satellite receiver, etc.) through the aerial cable,
switch them on. The automatic channel search
will recognise them and save them.
PLEASE WAIT
START FINISH
❚❚❚❚❚❚❚❚❚❚❚
❚❚❚❚❚❚❚❚❚❚❚❚
The video recorder does not find any TV
channels during the search
• Select channel 1 on the TV. Can you see the
saved TV channel on the TV?
If not, check the cable connection of the aerial
(aerial socket), video recorder, TV.
• The video recorder searches the entire frequen-
cy range in order to find and save the largest
possible number of TV channels. It is possible
that the TV channels in your country are broad-
cast in a higher frequency range. As soon as
this range is reached during the search, the
video recorder will find the TV channels.
TIME --:--
DATE --/--/--
END=EXIT
4. Installing your video recorder
6
MANUAL TUNING
→PROG. P55
CHANNEL 055
SKIP [OFF]
VIDEO MODE [SECAM]
AUDIO MODE [DK]
SELECT
KL CHOOSE B
END=EXIT
I don't know the channels for my TV stations
In this case, press or in
'CHANNEL' to start the automatic channel
search. A changing channel number will appear
on the TV screen. Continue the automatic search
until you have found the desired TV channel.
STOP C-LPLAY B-K
How do I change 'VIDEO MODE' or 'AUDIO
MODE'?
If you want to change the video or audio mode,
select 'VIDEO MODE' or 'AUDIO MODE' with
or . Then, press
to select your desired mode.
FWD 1- BSTOP C-LPLAY B-K
HG273ED(EN).qx3 04.2.3 10:54 AM Page 6
Automatic Tuning
During installation, all available TV channels are
searched for and saved. If the channel assign-
ments of your cable or satellite TV provider
change or if you are re-installing the video
recorder, e.g. after moving house, you can start
this procedure again. This will replace all the TV
channels already saved with the new ones.
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.
Select 'TUNER SET UP' with or
and confirm with .
4.
4.Select 'AUTO TUNING' with or
and confirm with
.
5.
5.The automatic TV channel search starts. This
allows the video recorder to save all available
TV channels. This procedure may take sever-
al minutes.
6.
6.When the TV channel search is complete,
'COMPLETED' will briefly appear on the TV
screen.
Sorting TV channels manually
After you have performed the automatic channel
search you may not agree with the sequence in
which the individual TV channels have been allo-
cated to the programme positions (programme
numbers) of the video recorder. You can use this
function to individually sort the TV channels
already saved.
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'TUNER SET UP' with
and confirm with .
4.
4.Select 'MOVE' with or ,
and confirm with .
5.
5.With or , select the saved
TV channel that you want to change.
6.
6.Confirm with .
7.
7.Move the selected channel with or
to the programme number you want
to assign.
8.
8.Confirm with .
9.
9.To assign other TV channels to a programme
number, repeat steps 5 to 8.
10.
10.To end, press .
STATUS/EXIT
FWD 1- B
STOP C-L
PLAY B-K
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
STOP C-L
PLAY B-K
MENU
FWD 1- BSTOP C-L
PLAY B-K
FWD 1- BSTOP C-L
PLAY B-K
MENU
EN
PLEASE WAIT
START FINISH
❚❚❚❚❚❚❚❚❚❚❚
❚❚❚❚❚❚❚❚❚❚❚❚
MOVE
→P01: 02 P06: 90
P02: 03 P07: 99
P03: 05 P08: 121
P04: 10 P09: 124
P05: 74 P10: 130
SELECT KL CHOOSE B
END=EXIT
7
HG273ED(EN).qx3 04.2.3 10:54 AM Page 7
EN
Setting the language
You can change the language for the TV screen
menu. However, the video recorder display will
only display English text regardless of this set-
ting.
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'INITIAL SET UP' with or
and confirm with .
4.
4.Select 'LANGUAGE' with or
and confirm with .
5.
5.Select the desired language with or
.
6.
6.To end, press .
Setting the clock
If the display shows an incorrect time or ' --:-- ',
the time and date must be reset manually.
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'INITIAL SET UP' with or
and confirm with
.
4.
4.Select 'CLOCK' with or
and confirm with .
5.
5.Check the time in 'TIME'. If required,
please change the time with .
6.
6.Check 'DAY', 'MONTH' and 'YEAR' in the
same way.
7.
7.To end, press .
Setting the RF out channel
In some reception locations it is possible that a
TV channel will be sent on the same or similar
frequency as the video recorder.
Result: As soon as the video recorder is
switched on, the reception quality for this or sev-
eral other TV channels will decrease.
The following steps will show you how to change
the pre-set 'transmission' (RF out channel) fre-
quency on the video recorder.
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'INITIAL SET UP' with or
and cconfirm with .
4.
4.Select 'RF OUT' with or
and confirm with .
5.
5.Press .
6.
6.Press ,
or to select a
free channel between channel 22 and
channled 69 in your area.
7.
7.Press
.
8.
8.Select 'TV SYSTEM’ with or
9.
9.
Choose 'K' or 'G' with
.
10.
10.To end, press .
STATUS/EXIT
FWD 1- B
STOP C-L
PLAY B-K
FWD 1- B
0..9
STOP C-LPLAY B-K
FWD 1- B
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
STOP C-L
PLAY B-K
MENU
STATUS/EXIT
0..9
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
STOP C-L
PLAY B-K
MENU
STATUS/EXIT
STOP C-L
PLAY B-K
FWD 1- B
STOP C-L
PLAY B-K
FWD 1- B
STOP C-L
PLAY B-K
MENU
TIME --:--
DATE --/--/--
END=EXIT
What is RF out channel?
This electronic component in the video recorder
allows the device to transmit audio and video
signals via the aerial cable. These signals can
be received on a TV just like TV channels.
What is RF out channel frequency?
This frequency or channel indicates the channel
on which the audio or video signal is transmitted.
SELECT KL CHOOSE B
→RF OUT CH 36
TV SYSTEM K
END=EXIT
8
If you cannot get an interference-free picture
and sound, connect the video recorder and
the TV with a scart cable. Then, switch the
built-in modulator off.
Press repeatedly until “--” appears
next to “RF OUT CH” on the TV screen.
Then confirm with
.
FWD 1- B
STOP C-L
END=EXIT
HG273ED(EN).qx3 04.2.3 10:54 AM Page 8
Playing back cassettes
You can operate the video recorder using the
remote control or the buttons on the front of the
video recorder.
If you press , ,
or
while the set is in Stand-by, the
power will be automatically turned on.
Additionally, if a cassette was already inserted,
the corresponding operation will be performed.
Your video recorder can only record and play
back standard VHS cassettes.
1.
1.Put a cassette into the cassette slot. The cas-
sette is inserted automatically. ' ' will
appear on the display.
2.
2.Press to view the tape. 'PLAY' will
appear on the display.
3.
3.To stop the playback, press or
on the video recorder.
4.
4.To eject the cassette, press when
the video recorder stops the playback.
Playing back NTSC cassettes
This video recorder can also play back cassettes
that have been recorded in SP [Standard Play]
or SLP [Super Long Play] mode in the NTSC
standard (for example, American cassettes).
However, this only works on PAL-television sets
that are suitable for a picture frequency of 60Hz.
Displaying current tape position
The following information is displayed on the
screen: e.g.: 0:02:45 shows the counter in hours,
minutes and seconds.
SP/LP: will show the recorded speed of your cassette.
Searching for a tape position with
picture (scanning)
1.
1.During playback, press (reverse) or
(forward).
2.
2.If you want to search in super high speed,
press or once more.
(This function will not operate for a NTSC cas-
settes playback in SP mode.)
3.
3.Press to resume playback.
Still picture
1.
1.During playback, press to stop the
tape and display a still picture.
2.
2.Press to resume playback.
Searching for tape position without
picture (forward wind and rewind)
1.
1.Stop the tape with .
2.
2.Press (reverse) or
(forward). 'Fr' or 'FF' will appear on the dis-
play for 5 seconds, and then, the real time
counter time will appear.
3.
3.To stop the tape, press .
Manual tracking
To manually adjust the tracking during playback,
press or .
Tracking will return to Automatic Tracking
Adjustment when you press , insert a
tape, or press .
To remove vertical jitter in a Still picture, press
or .
P–
P+
PROGRAMME
-
PROGRAMME
+
PLAY B-K
STOP C-L
P–P+
PROGRAMME
-
PROGRAMME
+
STOP C-L
FWD 1- B
REW0- s
STOP C-L
PLAY B-K
STILL
2
PLAY B-K
FWD 1- BREW0- s
FWD 1- B
REW0- s
STOP/EJECT
STOP/EJECT
STOP C-L
PLAY B-K
REW
0- s
FWD 1- BSTOP C-LPLAY B-K
EN
5. Playback
DIGITAL STUDIO PICTURE CONTROL
Philips has developed a system which produces
the best possible playback quality. For old and
often-used video cassettes, this system reduces
interference. For new or high quality cassettes,
it emphasises the details.
Picture/ sound quality is poor
When playing rental videos or older, poorer
quality cassettes, it may not be possible to com-
pletely filter out picture and sound interference.
This is not a fault in your machine. Read the
section 'Manual tracking'.
Automatic switch-off of special functions
Many functions (e.g. pause, still picture) switch
themselves off automatically after a short time in
order to protect the cassette and to save energy.
Do I need to change the playback speed
when playing back LP recordings?
During playback, the correct speed will automati-
cally be selected. For more information, please
read the section 'Selecting the recording speed
(SP or LP)' in the chapter 'Manual recording'.
How can I set the counter to '0:00:00'?
You can set the counter to '0:00:00' with .
When you put a cassette in the video recorder,
the counter will automatically reset to '0:00:00'.
CLEAR
The counter does not move
This occurs when there are no recordings on a por-
tion of a tape. This is not a fault in your video recorder.
The screen shows '-0:01:20'
If you rewind a cassette from the tape position
'0:00:00', the counter will show for instance,
'-0:01:20' (the cassette was rewound to
1 minute and 20 seconds before '0:00:00').
9
Scanning and still picture interfere with the
picture quality
Please note that the sound is muted during
those functions.
•You may observe noiselines on the TV screen
while in Still mode. This is normal. Note that
each time you press the lines will
change position.
• If you observe a vertical jitter of the picture, sta-
bilize it by pressing
or while in Still mode.
P–P+
PROGRAMME
-
PROGRAMME
+
STILL
2
HG273ED(EN).qx3 04.2.6 10:58 AM Page 9
General information
Use 'Manual Recording' to make a sponta-
neous recording (for example, a programme cur-
rently being shown).
If you want to start and stop a recording manual-
ly, read the section
'Recording without auto-
matic switch-off'
.
If you want to start a recording manually but
have it stopped automatically, read the section
'Recording with automatic switch-off'.
(e.g. not to record to the end of the tape)
Recording without automatic
switch-off
1.
1.Insert a cassette.
2.
2.Use to select the programme num-
ber you want to record, for example, 'P01'.
3.
3.To start recording, press .
4.
4.Stop recording with .
Recording with automatic switch-off
(OTR One-Touch-Recording)
1.
1.Insert a cassette.
2.
2.Use to select the programme num-
ber you want to record.
3.
3.Press .
4.
4.Each time you press you will add 30
minutes to the recording time.
5.
5.Stop recording with .
Preventing accidental erasing)
All cassettes (except rental and pre-recorded
cassettes) have a security tab on the back of the
cassette.
To prevent recording over important recordings
(erasing), you can remove this security tab.
If you later decide to record on a protected cas-
sette, simply cover the hole with adhesive tape
or slide the tab to the right.
Lining up recordings (assemble cut)
When you add a further recording to a cassette,
which already has a recording on it, a short
blank (flicker) can appear between the old and
the new recording or the picture itself can flicker.
To help reduce these from occurring, proceed as
follows:
1.
1.Find the tape position of the old recording
where you want to insert the new recording.
2.
2.Look at the last minute of the old recording
(playback).
3.
3.Press at the tape position where the
new recording is to go and press .
4.
4.Now start recording as usual by pressing
on the remote control.
5.
5.Stop recording with .
Selecting the recording speed (SP or LP)
LP allows to double the recording duration on
tape (for example six hours instead of three
hours on a E180 cassette).
1.
1.Switch on the TV. If required, select the
programme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'RECORD SETUP' using or
and confirm with
.
4.
4.Select the required recording speed with
.
5.
5.To end, press .
STATUS/EXIT
FWD 1- B
FWD 1- B
STOP C-L
PLAY B-K
MENU
STOP C-L
REC I
REC I
STILL
22
STOP C-L
REC I
REC I
P–P+
STOP C-L
REC I
P–P+
EN
6. Manual recording
10
‘PROTECTED CASETTE CANNOT RECORD’ mes-
sage briefly appeared in the TV screen, then the
cassette was ejiected.
A cassette without the security tab was inserted. Undo
the erase protection.
SELECT KL CHOOSE B
→RECORD SPEED [SP]
END=EXIT
'SP' / 'LP'
'SP': Standard Play (normal recording speed)
offers the usual first-class picture quality.
'LP': Long Play (half recording speed, double
recording time). 6 hours can be recorded on a
3-hour cassette (E180) with a somewhat
reduced picture quality.
HG273ED(EN).qx3 04.2.3 10:54 AM Page 10
General information
Use a TIMER programming to automatically start
and stop a recording at a later time or date. The
video recorder will switch to the right programme
number and begin recording at the correct time.
With this video recorder, you can pre-programme
up to eight recordings within a period of one
year. To make a programmed recording, your
video recorder needs to know:
* the date you want to make the recording
* the programme number of the TV channel
* the start and stop time of the recording
This information is saved in a 'TIMER' block.
Programming a recording
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'TIMER' with or .
Then press .
4.
4.Select ‘ONCE’, ‘DAILY’, or ‘WEEKLY’ record-
ing with or . Then press
.
5.
5.Select TIMER block with .
6.
6.Enter the Start time (START), End time
(STOP), Programme number (PROG) and the
Date (DATE) with
7.
7.When all inputs are correct, press
. The programming information
is stored in a TIMER block.
8.
8.Insert a cassette with an intact security tab
(unprotected).
9.
9.Switch off with .
The programmed recording will only function
when the video recorder is switched off with
.
How to check, or delete a pro-
grammed recording (TIMER)
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'TIMER' with or .
Then press .
4.
4.Select 'TIMER LIST' with or ,
and confirm with
.
5.
5.Select timer block with .
6.
6.To cancel the recording, press .
7.
7.To end, press
.
8.
8.Switch off with
.
STANDBY/ON
yy
STATUS/EXIT
CLEAR
FWD 1- B
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
STOP C-LPLAY B-K
MENU
STANDBY/ON
yy
STANDBY/ON
yy
STATUS/EXIT
0..9
0..9
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
STOP C-LPLAY B-K
MENU
EN
7. Programming a recording (TIMER)
SELECT KL CHOOSE B
→ONCE
DAILY
WEEKLY
TIMER LIST
END=EXIT
SelectingONCE/DAILY/WEEKLY recordings
'ONCE': Recording once
'DAILY': Repeated daily recordings from
Monday to Friday
'WEEKLY.': Repeated weekly recordings
(every week on the same day)
Error message : ' FULL '
• If this error message appears after you
select 'ONCE', 'DAILY', or 'WEEKLY' on
TIMER menu and press
, then all
TIMER blocks are already programmed. No
more recordings can be programmed. If you
want to clear or check a programmed record-
ing(TIMER block), select the programme num-
ber on TIMER LIST menu and press
.
CLEAR
FWD 1- B
Programme numbers of the ‘TV’ scart socket
You can also programme recordings from exter-
nal sources via scart socket ‘TV’. Select pro-
gramme number, 'A/V IN' with 0.0.
11
SELECT KL CHOOSE B
ONCE
DAILY
WEEKLY
→TIMER LIST
END=EXIT
Timer block disappeared when I pressed
.
You have checked all the programmed record-
ings. If you want to check them again, repeat
steps 2 to 5.
FWD 1- B
HG273ED(EN).qx3 04.2.3 10:54 AM Page 11
How to change a programmed
recording (TIMER)
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'TIMER' with or .
Then press .
4.
4.Select ONCE, DAILY, or WEEKLY recording
with or . Then press
.
5.
5.Select a TIMER block with . (The flashing
number indicates an empty TIMER block.)
6.
6.Press
to delete information and input
correct information with
.
7.
7.To end, press
.
8.
8.Switch off with
.
Problems and solutions for pro-
grammed recordings
STANDBY/ON
yy
STATUS/EXIT
0..9
CLEAR
0..9
FWD 1- B
STOP C-LPLAY B-K
FWD 1- B
STOP C-LPLAY B-K
MENU
ONCE
TIMER - 1 2 3 4 5 6 7 8 -
SELECT TIMER NUMBER
END=EXIT
12
Error message: ' ' flashes in the video
recorder display
•
No cassette was inserted. Insert a cassette and
switch off the video recorder using
.
Cassette was ejected as soon as the
button was pressed
• A cassette without the security tab was inserted.
Undo the erase protection (chapter 'Manual
recording', section 'Preventing accidental eras-
ing') or insert a different cassette.
'TURN OFF VCR FOR TIMER RECORDING'
flashes on the TV screen
• The video recorder is switched on several min-
utes before the start of a programmed recording.
Switch off the video recorder with
. A programmed recording (timer)
will only function when the video recorder is
switched off.
Cassette is ejected during recording
•
The end of the tape was reached during recording.
The video recorder does not react
• While a programmed recording is being made,
you cannot operate your video recorder manu-
ally. If you want to cancel the programmed
recording, press on the front panel.
STOP/EJECT
STANDBY/ON
yy
STANDBY/ON
yy
STANDBY/ON
yy
HG273ED(EN).qx3 04.2.3 10:54 AM Page 12
EN
8. Other Functions
Changing the video (colour) system
If you playback recordings made on other video
recorders or you want to record from external
sources (via the scart socket), the automatic
video (colour) system switch-over may lead to
colour distortion.
You can switch off the automatic TV system
switch-over as follows.
1.
1.Press on the remote control to
select the TV (colour) system with the least
disruptions during playback.
Each pressing , the display will
change cyclicaly; AUTO, ME-SECAM, PAL.
2.
2.After 5 seconds, the OSD will disappear.
Switching the status display off or on
Along with the on screen menu, the status dis-
play also displays information on the current
operating status (counter, playback, recording,
TV channel, etc.) on the TV screen. You can
switch off the information about the operating
status so that the status display is not recorded
when copying videocassettes.
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'VCR SET UP' with or
and confirm with .
4.
4.Select 'STATUS DISPLAY' with or
.
5.
5.Select 'ON' or 'OFF' with .
6.
6.To end, press .
Blue Background on or off
If you want the TV screen to be solid blue when
a weak signal is received, set BLUE BACK-
GROUND to ‘ON’. The screen will be blue and
the sound will be muted. Or, if you want to
receive the weak signal, set BLUE BACK-
GROUND to ‘OFF’.
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'VCR SET UP' using
and confirm with .
4.
4.Select 'BLUE BACKGROUND' with
.
5.
5.Select 'OFF' (no blue background) or 'ON'
(blue background on) with .
6.
6.To end, press .
STATUS/EXIT
FWD 1- B
STOP C-L
PLAY B-K
FWD 1- BSTOP C-L
PLAY B-K
MENU
STATUS/EXIT
FWD 1- B
STOP C-L
PLAY B-K
FWD 1- B
STOP C-LPLAY B-K
MENU
SYSTEM
SYSTEM
SELECT KL CHOOSE B
→STATUS DISPLAY [ON]
BLUE BACKGROUND [ON]
AUTO STANDBY [ON]
CLOCK DISPLAY [ON]
END=EXIT
Which settings can I choose?
'ON': Shows the status display
for a few seconds only.
'OFF': Switches off the status display.
SELECT KL CHOOSE B
STATUS DISPLAY [ON]
→BLUE BACKGROUND [ON]
AUTO STANDBY [ON]
CLOCK DISPLAY [ON]
END=EXIT
13
Video (colour) systems
Other countries, other video (colour) systems:
In central Europe transmissions are broadcast
in the PAL system (Phase Alternation Line)
standard. France uses SECAM (Séquentiel à
mémoire). Middle East countries use ME-
SECAM (Middle East SECAM).In some coun-
tries (USA and Japan), TV viewers receive their
programmes as an NTSC signal (National
Television System Committee).
AUTO
HG273ED(EN).qx3 04.2.3 10:54 AM Page 13
EN
Automatic switch-off
If you haven't used the video recorder for a few
minutes in certain modes (e.g.: STOP), it will
switch to standby automatically. You can cancel
this function to use the video recorder as a tele-
vision receiver.
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'VCR SET UP' using or
and confirm with .
4.
4.Select 'AUTO STANDBY' using or
.
5.
5.Select 'OFF' (no automatic switch-off) or 'ON'
(automatic switch-off) with .
6.
6.To end, press .
Clock Display
This function allows you to switch the VCR dis-
play off. It is useful in case you feel disturbed by
the display-brightness while watching TV in a
dark room. It also reduces the power consump-
tion.
1.
1.Switch on the TV. If required, select the pro-
gramme number for the video recorder.
2.
2.Press . The main menu will appear.
3.
3.Select 'VCR SET UP' using or
and confirm with .
4.
4.Select 'CLOCK DISPLAY' using or
.
5.
5.Select 'OFF' (no clock display) or 'ON' (clock
display on) with .
6.
6.To end, press .
STATUS/EXIT
FWD 1- B
STOP C-L
PLAY B-K
FWD 1- BSTOP C-L
PLAY B-K
MENU
STATUS/EXIT
FWD 1- B
STOP C-L
PLAY B-K
FWD 1- B
STOP C-LPLAY B-K
MENU
SELECT KL CHOOSE B
STATUS DISPLAY [ON]
BLUE BACKGROUND [ON]
→AUTO STANDBY [ON]
CLOCK DISPLAY [ON]
END=EXIT
14
SELECT KL CHOOSE B
STATUS DISPLAY [ON]
BLUE BACKGROUND[ON]
AUTO STANDBY [ON]
→CLOCK DISPLAY [ON]
END=EXIT
HG273ED(EN).qx3 04.2.3 10:54 AM Page 14
EN
No picture when you play a cassette:
• There is no recording on the cassette: change
the cassette.
• You have selected the wrong programme
number on the TV for playing cassette: on the
TV, select the correct programme number for
the video recorder.
• The cable connecting the TV and the video
recorder has come loose: check the cable.
Poor picture quality when you play a cas-
sette:
• Your TV is not properly adjusted.
• The cassette is badly worn or of poor quality:
use new cassette.
• Tracking is not properly adjusted: turn to sec-
tion 'Manual tracking'.
No recording possible:
• The TV channel you want to record is not
stored or you selected the wrong programme
number: check TV channels stored.
• A cassette was inserted that does not have
the security tab (cannot be used to record):
cover the hole with adhesive tape or use a
cassette with an intact security tab. For more
information, please see the section
'Preventing accidental erasing' in chapter
'Manual recording'.
There is picture or sound interference on TV
reception:
• Turn to chapter 'Installing your video recorder'
and read 'Setting the RF out channel'.
• Have your aerial checked.
9. Before you call an engineer
If, contrary to expectation, you have any prob-
lems using this video recorder, it may be caused
by the following reasons.
Your video recorder does not respond to
any button being pressed:
There is no power supply: check the power sup-
ply.
• A programmed recording is currently being
made: if desired, cancel the programmed
recording. Please see the section 'Problems
and solutions for programmed recordings' in
chapter 'Programming a recording (TIMER)'
• There is a technical problem: disconnect from
the mains power supply for 60 seconds, then
connect again.
If this doesn't help, you could reset your video
recorder to the default factory settings.
Resetting devices to default factory settings
* Attention:
All the information stored (TV channels, time
and date, TIMER) will be cleared.
1.Switch off this video recorder with
.
2.Press and hold and
for 2 seconds or more at the same time.
Cassette is jammed in the video recorder:
• Don't use force. Pull out the mains plug for the
moment. Then, call an engineer.
Remote control does not work:
• Remote control not pointed toward the video
recorder: point it at the video recorder.
• There is a technical problem: Take out the bat-
teries, wait for 10 seconds and place them
back.
• Batteries have run out: change the batteries.
PROGRAMME+
STOP/EJECT
STANDBY/ON
yy
15
You can also call the customer service centre
in your country.
The telephone numbers can be found on page
16 of this operating manual. Have the model
number (MODEL NO.) and the production num-
ber (PROD.NO.) of your video recorder ready.
HG273ED(EN).qx3 04.2.3 10:54 AM Page 15
EN
PHILIPS NORGE AS
Sandstuveien 70,
PO Box 1, Manglerud
N-0612 Oslo
NORWAY
Phone: 2274 8250
OY PHILIPS AB
Linnoitustie 11,
02600 Espoo
FINLAND
puh. 09 615 80 250
PHILIPS KUNDTJÄNST
Kista Entré
Knarrarnäsgatan 7
164 85 Stockholm
SWEDEN
Tel: (0)8 598 52 250
PHILIPS POLSKA
Al. Jerozolimskie 195B
02-222 Warszawa
POLSKA
TEL.: (022)-571-0-571
INFOLINKA PHILIPS
Safránkova 1
150 00 Praha 5
CZECH REPUBLIC
TEL.: (02)-330 99 330
PHILIPS Iberia, S.A.
C/Martinez Villergas, 49
28027 MADRID
SPAIN
Phone: 902-11 33 84
PHILIPS AUSTRIA GMBH
Triesterstrasse 64
1101 Wien
AUSTRIA
Tel: 0810 001 203
PHILIPS INFO CENTER
Alexanderstrasse 1
20099 Hamburg
GERMANY
Tel: 0180-53 56 767
SERVICE CONSOMMATEURS PHILIPS
BP 0101
75622 Paris Cédex 13
FRANCE
Phone: 0825-889 789
PHILIPS ELECTRONICS IRELAND LIMITED
Consumer Information Centre
Newstead, Clonskeagh
DUBLIN 14
Phone: 01-7640292
PHILIPS CONSUMER ELECTRONICS
Servizio Consumatori
Via Casati 23
20052 Monza - Milano
ITALY
Phone: 199 118899
PHILIPS MAGYARORSZÁG KFT.
Fehérvári út 84/a.
Budapest 1119
HUNGARY
Phone: (01)-382-1700
PHILIPS PORTUGUESA, S.A.
Consumer Information Centre
Rua Dr. António Loureiro Borge, nr. 5
Arquiparque, Miraflores
P-2795 L-A-VEHLA
PORTUGAL
Phone: 021-4163063
PHILIPS CE, The Philips Centre,
420 - 430 London Road,
Croydon, Surrey
CR9 3 QR
UNITED KINGDOM
Phone: 0208-665-6350
PHILIPS KUNDECENTER
Frederikskaj 6,
1780 København V
DANMARK
Tlf.: 80 88 28 14
PHILIPS REPRESENTATION OFFICE
Ul. Usacheva 35a
119048 MOSCOW
RUSSIA
Phone: 095-937 9300
PHILIPS INFO CENTER
Fegistrasse 5
8957 Spreitenbach
SUISSE
Tel.: 0844-800 544
PHILIPS CUSTOMER CARE CENTER
Twee Stationsstraat 80/
80 Rue des Deux Gares
1070 BRUSSEL/BRUXELLES
BELGIUM (for BENELUX)
Tel: 070-222303
PHILIPS CONSUMENTENLIJN
Postbus 102 5600 AC Eindhoven
NEDERLAND
Tel.: 0900-8406
16
HG273ED(EN).qx3 04.2.3 10:54 AM Page 16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Philips XX-VR150/58 User manual

Philips
Brand
Philips
Model
XX-VR150/58
Category
Cassette players
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents