BLACK+DECKER GL720 User manual

Page is loading ...

4

ENGLISH

Intended use

Your Black & Decker strimmer GL701/GL716/

GL720/GL741 has been designed for trimming and

ﬁ nishing lawn edges and to cut grass in conﬁ ned

spaces.This tool is intended for consumer use only.

Safety instructions

• Warning! When using mains-powered

tools, basic safety precautions, including the

following, should always be followed to reduce

the risk of ﬁ re, electric shock, personal injury

and material damage.

• Read all of this manual carefully before

operating the tool.

• Retain this manual for future reference.

• Remove the plug from the socket before

carrying out any adjustment, servicing or

maintenance.

Keep work area clean

Cluttered areas and benches can cause accidents.

Consider work area environment

Do not expose the tool to rain. Do not use the tool

in damp or wet conditions. Keep the work area

well lit. Do not use the tool where there is a risk of

causing ﬁ re or explosion, e.g. in the presence of

ﬂ ammable liquids and gases.

Keep children away

Do not allow children, visitors or animals to come

near the work area or to touch the tool or mains

cable.

Dress properly

Do not wear loose clothing or jewellery, as these

can be caught in moving parts. Preferably wear

rubber gloves and non-slip footwear when working

outdoors. Wear protective hair covering to keep

long hair out of the way.

Personal protection

Always use safety glasses. Use a face or dust

mask whenever the operations may produce dust

or ﬂ ying particles. Hearing protection should be

worn.

Guard against electric shock

Prevent body contact with earthed or grounded

surfaces (e.g. pipes, radiators, cookers and

refrigerators). Electric safety can be further

improved by using a high-sensitivity (30 mA / 30

mS) residual current device (RCD).

Do not overreach

Keep proper footing and balance at all times.

Stay alert

Watch what you are doing. Use common sense.

Do not operate the tool when you are tired.

Secure workpiece

Use clamps or a vice to hold the workpiece. It is

safer and it frees both hands to operate the tool.

Connect dust extraction equipment

If devices are provided for the connection of dust

extraction and collection facilities, ensure that

these are connected and properly used.

Remove adjusting keys and wrenches

Always check that adjusting keys and wrenches

are removed from the tool before operating the

tool.

Extension cables

Before use, inspect the extension cable and

replace if damaged. When using the tool outdoors,

only use extension cables intended for outdoor

use. Up to 30 m of Black & Decker extension cable

can be used without loss of power.

Use appropriate tool

The intended use is described in this instruction

manual. Do not force small tools or attachments

to do the job of a heavy-duty tool. The tool will do

the job better and safer at the rate for which it was

intended. Do not force the tool. Do not use the tool

for purposes not intended, for example, do not use

a circular saw to cut tree limbs or logs.

Warning! The use of any accessory or attachment

or performance of any operation with this tool other

than those recommended in this instruction manual

may present a risk of personal injury.

Check for damaged parts

Before use, carefully check the tool and mains

cable for damage. Check for misalignment and

seizure of moving parts, breakage of parts,

damage to guards and switches and any other

conditions that may affect its operation. Ensure

that the tool will operate properly and perform its

intended function. Do not use the tool if any part

is damaged or defective. Do not use the tool if

the switch does not turn it on and off. Have any

damaged or defective parts repaired or replaced

by an authorised repair agent. Never attempt any

repairs yourself.

Unplug the tool

Unplug the tool when it is not in use, before

changing any parts of the tool, accessories or

attachments and before servicing.

Avoid unintentional starting

Do not carry the tool with a ﬁ nger on the on/off

switch. Be sure that the tool is switched off when

plugging in.

Do not abuse cord

Never carry the tool by its cord or pull it to disconnect

from the socket. Keep the cord away from heat, oil

and sharp edges.

5

ENGLISH

Store idle tools

When not in use, tools should be stored in a dry,

locked up or high place, out of reach of children.

Maintain tools with care

Keep cutting tools sharp and clean for better and

safer performance. Follow the instructions for

maintenance and changing accessories. Keep

handles and switches dry, clean and free from oil

and grease.

Repairs

This tool complies with relevant safety

requirements. Repairs should only be carried out

by qualiﬁ ed persons using original spare parts;

otherwise this may result in considerable danger to

the user.

Electrical safety

This tool is double insulated; therefore

no earth wire is required. Always check

that the power supply corresponds to the

voltage on the rating plate.

• This appliance is not intended for use by young

or inﬁ rm persons without supervision. Children

must be supervised to ensure they do not play

with the appliance.

• If the supply cord is damaged, it must be

replaced by the manufacturer or an authorised

Black & Decker Service Centre in order to

avoid a hazard.

Additional safety instructions for grass

trimmers

The following warning symbols are found on the

tool:

Read the manual prior to operation.

Wear safety glasses or goggles when

operating this tool.

Keep people and animals at least 6 m

away from the cutting area.

Do not expose the tool to rain or high

humidity.

• Be familiar with the controls and the proper use

of the equipment.

• Only use the machine in daylight or good

artiﬁ cial light.

• Before use check the supply and extension

cord for any signs of damage or ageing.

If the cord becomes damaged during

use, disconnect the cord from the supply

immediately. DO NOT TOUCH THE CORD

BEFORE DISCONNECTING THE SUPPLY

• Do not use the lawn trimmer (edge trimmer), if

the cords are damaged or worn.

• Wear stout shoes or boots to protect your feet.

• Wear long trousers to protect your legs.

• Before using the tool, check that your cutting

path is free from sticks, stones, wire and any

other obstacles.

• Only use the tool in the upright position, with

the cutting line near the ground. Never switch

the tool on in any other position.

• Move slowly when using the tool. Be aware

that freshly cut grass is damp and slippery.

• Do not work on steep slopes. Work across the

face of slopes, not up and down.

• Never cross gravel paths or roads while the

tool is running.

• Never touch the cutting line while the tool is

running.

• Do not put the tool down until the cutting line

has come to a complete standstill.

• Use only the appropriate type of cutting line.

Never use metal cutting line or ﬁ shing line.

• Be careful not to touch the line trimming blade.

• Take care to keep the mains cable away

from the cutting line. Always be aware of the

position of the cable.

• Keep hands and feet away from the cutting

means at all times and especially when

switching on the motor.

• Warning. Cutting elements continue to rotate

after the motor is switched off.

• Never operate the machine with damaged

guards or without the guards in place.

• Always ensure that the ventilation openings

are kept clear of debris.

Features

This tool includes some or all of the following

features.

1. On/off switch

2. Handle

3. Cable restraint

4. Power inlet

5. Secondary handle

6. Adjustment button

7. Tube

8. Guard

9. Line trimming blade

10. Spool housing

11. Cutting line

12. Edge guide

6

ENGLISH

Assembly

Warning! Before assembly, make sure that the tool

is switched off and unplugged.

Fitting the guard (ﬁ g. A)

• Remove the Allen screws (13) from the head

(14).

• Place the guard (8) onto the tool as shown.

• Firmly press the guard until it snaps into place.

• Secure the guard with the Allen screws.

• Tighten the Allen screws using the Allen key

(15) provided.

Warning! Never use the tool unless the guard is

properly ﬁ tted.

Releasing the cutting line

In transit, the cutting line is taped to the spool

housing.

• Remove the tape holding the cutting line (11)

to the spool housing (10).

Connecting the tool to the mains

• Connect the female plug of a suitable

extension cable to the power inlet (4).

• Loop the cable through the cable restraint (3).

• Insert the mains plug into a mains outlet.

Warning! The extension cable must be suitable for

outdoor use.

Use

Warning! Let the tool work at its own pace. Do not

overload.

Setting the tool to trimming or edging mode

(ﬁ g. B - D)

The tool can be used in trimming mode as shown

in ﬁ g. B or in edging mode to trim overhanging

grass along lawn edges and ﬂ ower beds as shown

in ﬁ g. C.

Trimming mode (ﬁ g. B & D)

For trimming, the trimmer head should be in the

position shown in ﬁ g. B. If it is not:

• Depress the adjustment button (6).

• Rotate the tube (7), while releasing the button.

• When the head is in position, the button will

lock into place.

Note: The tube will only rotate in one direction.

Edging mode (ﬁ g. C & D) For edging, the trimmer

head should be in the position shown in ﬁ g. C. If it

is not:

• Depress the adjustment button (6).

• Rotate the tube (7), while releasing the button.

• When the head is in position, the button will

lock into place.

Note: The tube will only rotate in one direction.

Adjusting the height of the tool (ﬁ g. D)

This tool has a telescopic mechanism, allowing

you to set it to a comfortable height. There are

three height settings. To adjust the height setting,

proceed as follows:

• Depress the adjustment button (6).

• Gently pull the tube (7) out of the motor

housing (15) to the desired height, while

releasing the button.

• When the tube is in position, the button will

lock into place.

Switching on and off

• To switch the tool on, squeeze the trigger lever

(1).

• To switch the tool off, release the trigger lever.

Warning! Never attempt to lock the trigger lever in

the on position.

Hints for optimum use

General

• In order to achieve optimum cutting results,

only cut dry grass.

Trimming

• Hold the tool as shown in ﬁ g. B.

• Gently swing the trimmer from side to side.

• When cutting long grass, work in stages from

the top.

Take small cuts.

• Keep the tool away from hard objects and

delicate plants.

• If the tool starts running slowly, reduce the

load.

Edging

Optimum cutting results are achieved on edges

deeper than 50 mm.

• Do not use the tool to create edges. To create

edges, use an edging spade.

• Guide the tool as shown in ﬁ g. C.

• To make a closer cut, slightly tilt the tool.

Maintenance

Your tool has been designed to operate over a long

period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon

proper tool care and regular cleaning.

7

ENGLISH

Warning! Before performing any maintenance,

switch off and unplug the tool.

• Regularly clean the ventilation slots in your tool

using a soft brush or dry cloth.

• Regularly clean the cutting line and spool using

a soft brush or dry cloth.

• Regularly use a blunt scraper to remove grass

and dirt from the underneath of the guard.

Fitting a new spool of cutting line (ﬁ g. E & F)

Replacement spools of cutting line are available

from your Black & Decker dealer (cat. no. A6495).

• Keep the tabs (17) depressed and remove the

spool cover (18) from the housing (10).

• Remove the empty spool (19) from the spool

housing.

• Remove any dirt and grass from the spool

cover and housing.

• Take the new spool and push it onto the boss

in the spool cover. Rotate the spool slightly

until it is seated.

• Unclip the end of one of the cutting lines and

guide the line into one of the eyelets (20). The

line should protrude approx. 11 cm from the

spool cover.

• Unclip the end of the other cutting line and

guide the line into the other eyelet. The line

should protrude approx. 11 cm from the spool

cover.

• Align the tabs (17) on the spool cover with the

cut outs (21) in the housing.

• Push the cover onto the housing until it snaps

securely into place.

Warning! If the cutting lines protrude beyond the

trimming blade (9), cut them off so that they just

reach the blade.

Winding new line onto an empty spool (ﬁ g. G - I)

You may wind new cutting line onto an empty

spool.Replacement packs of cutting line are

available from your Black & Decker dealer (cat. no.

A6171).

• Remove the empty spool from the tool as

described above.

• Remove any remaining cutting line from the

spool.

• First wind new line onto the uppermost part of

the spool:

– Feed 2 cm of cutting line into one of the

slots in the upper section of the spool as

shown.

– Wind the cutting line onto the spool in the

direction of the arrow. Make sure to wind the

line on neatly and in layers. Do not criss-cross.

– When the wound cutting line reaches the

recesses (22), cut the line.

– Temporarily park the line in the slots (23)

on one side of the spool as shown.

• Repeat the above procedure for the second

cutting line on the lower section of the spool.

Park the line in the unused slots (23).

• Proceed as described above to ﬁ t the spool on

the tool. Do not forget to release the cutting

line from the parking slots (23).

Warning! Only use the appropriate type of

Black & Decker cutting line. Ensure that cutting line

is present in both sections of the spool.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be ﬁ tted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the

new plug.

• Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth

terminal. Follow the ﬁ tting instructions supplied

with good quality plugs. Recommended fuse: 5 A.

Troubleshooting

If your tool seems not to operate properly, follow

the instructions below. If this does not solve the

problem, please contact your local Black & Decker

repair agent.

Warning! Before proceeding, unplug the tool.

Tool runs slowly

• Check that the spool housing can rotate freely.

Carefully clean it if necessary.

• Check that the cutting line does not protrude

more than 11 cm from the spool housing. If it

does, cut it off so that it just reaches the line

trimming blade.

Automatic line feed does not work

• Keep the tabs depressed and remove the

spool cover from the housing.

• Pull the cutting line until it protrudes 11 cm

from the housing. If insufﬁ cient cutting line is

left on the spool, install a new spool of cutting

line as instructed above.

• Align the tabs on the spool cover with the cut

outs in the housing.

• Push the cover onto the housing until it snaps

securely into place.

• If the cutting line protrudes beyond the

trimming blade, cut it off so that it just reaches

the blade.

8

If the automatic line feed still does not work or the

spool is jammed, try the following suggestions:

• Carefully clean the spool cover and housing.

• Remove the spool and check if the lever can

move freely.

• Remove the spool and unwind the cutting

line, then wind it on neatly again as described

above. Replace the spool as instructed.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you ﬁ nd one day that your Black & Decker

product needs replacement, or if it is of no further

use to you, do not dispose of it with household

waste. Make this product available for separate

collection.

Separate collection of used products and

packaging allows materials to be recycled

and used again. Reuse of recycled materials

helps prevent environmental pollution and

reduces the demand for raw materials.

Local regulations may provide for separate

collection of electrical products from the

household, at municipal waste sites or by the

retailer when you purchase a new product.

Black & Decker provides a facility for the collection

and recycling of Black & Decker products once

they have reached the end of their working life. To

take advantage of this service please return your

product to any authorised repair agent who will

collect them on our behalf.

You can check the location of your nearest

authorised repair agent by contacting your local

Black & Decker ofﬁ ce at the address indicated in

this manual. Alternatively, a list of authorised

Black & Decker repair agents and full details of our

after-sales service and contacts are available on

the Internet at: www.2helpU.com

Technical data

GL701 GL716 GL720 GL741

Voltage V

AC

230 230 230 230

Power input W 550 580 600 700

No-load speed min

-1

6,500 6,500 6,500 6,500

Weight kg 3.2 3.2 3.2 3.2

EC declaration of conformity

GL701/GL716/GL720/GL741

Black & Decker declares that these products

conform to: 98/37/EC, 89/336/EEC, 73/23/EEC,

EN 60335, EN 55014, EN 61000, 2000/14/EC,

Annex VIII, Lawn trimmer, L ≤ 50 No. 0344, KEMA

Quality B.V., Utrechtseweg 310, 6802 ED Arnhem,

The Netherlands

Level of sound pressure, measured according to

2002/14/EC:

L

pA

(sound pressure) 81 dB(A)

L

WA

(acoustic power) 95 dB(A)

L

WA

(guaranteed) 96 dB(A)

Hand/arm weighted vibration value according to

EN 786: < 2,5 m/s

2

Kevin Hewitt

Director of Consumer

Engineering

Spennymoor, County Durham

DL16 6JG, United Kingdom

1-11-2005

UK patent application no. 059745.6

European Community design application nos.

340385-0001 & 339544-0001

ENGLISH

9

ENGLISH

Guarantee

Black & Decker is conﬁ dent of the quality of its

products and offers an outstanding guarantee. This

guarantee statement is in addition to and in no way

prejudices your statutory rights. The guarantee is

valid within the territories of the Member States of the

European Union and the European Free Trade Area.

If a Black & Decker product becomes defective

due to faulty materials, workmanship or lack of

conformity, within 24 months from the date of

purchase, Black & Decker guarantees to replace

defective parts, repair products subjected to fair

wear and tear or replace such products to ensure

minimum inconvenience to the customer unless:

• The product has been used for trade, professional

or hire purposes;

• The product has been subjected to misuse or

neglect;

• The product has sustained damage through

foreign objects, substances or accidents;

• Repairs have been attempted by persons

other than authorised repair agents or

Black & Decker service staff.

To claim on the guarantee, you will need to submit

proof of purchase to the seller or an authorised

repair agent. You can check the location of your

nearest authorised repair agent by contacting

your local Black & Decker ofﬁ ce at the address

indicated in this manual. Alternatively, a list of

authorised Black & Decker repair agents and full

details of our after-sales service and contacts are

available on the Internet at: www.2helpU.com

Please visit our website

www.blackanddecker.co.uk to register your

new Black & Decker product and to be kept up to

date on new products and special offers. Further

information on the Black & Decker brand and our

range of products is available at

www.blackanddecker.co.uk

Page is loading ...

www.blackanddecker.com

479753-02

BLACK+DECKER GL720 User manual

This manual is also suitable for

BLACK+DECKER GL720 User manual

in other languages

Related papers

Other documents