PRO SIGNAL 50-14797. Operating instructions

Brand: PRO SIGNAL

Model: 50-14797.

Type: Operating instructions

70"

MAX

75x75/100x100

200x100/200x200

300x300/400x200

400x400/600x400

ISSUED: APR. 2014

CAUTION : DO NOT EXCEED RATED

LISTED WEIGHT CAPACITY. SERIOUS

INJURY OR PROPERTY DAMAGE MAY

OCCUR!

ASSEMBLY INSTRUCTIONS

Model 50-14797

50kg

(110lbs)

RATED

TV STANDS

www.mcmelectronics.com Model 50-14797

Warranty

This device is warranted against manufactures defects for a period of 1 year from the original date of

purchase. This warranty covers all internal components and the cost of labor to either repair or replace

the unit. This warranty covers only the unit, and does not cover connected equipment, or any loss that

may occur, regardless of cause. It will be the sole discretion of MCM Electronics to determine the

applicability of said warranty, and determination as to whether the unit will be repaired or replaced.

Questions regarding application, use, or problems with this unit should be directed to MCM Electronics

Tech Support, which can be found at www.mcmelectronics.com.

This completes the assembly steps of this stand.

As noted earlier, it is the ultimate responsibility of the user to ensure safe and secure

Installation of any television on this stand. There is no guarantee that every television,

even if within the size and weight limits specified, will be secure in every situation.

Once installation is complete, the user must make certain the television set is secure.

Failure to do so could result in property damage, electrical or fire hazard and personal

injury or death, should the television fall. Pro Signal, MCM Electronics and all retail

dealers providing this product cannot be held liable for damages that result from improper

or insecure installation.

Furniture including tables, dressers, entertainment centers and shelves must be tested

to ensure stability

Televisions should be installed out of reach of small children or pets that could potentially

pull or knock a set from its location

Connecting cables, including power cords, cable, antenna or satellite TV wires, cables

from other components, indoor antennas and similar items should be secured and tucked

out of the way to prevent being snagged or tripped over

Televisions should not be located in direct sunlight or in locations where they can come in

contact with rain or moisture.

Things to remember:

In the event the user is not confident in the safety of this installation it is highly

recommended that a qualified installation professional be contacted.

A1x6 A2x8 A3x14

A4x6 A5x4 A6x4

A7x1

B2x2

B5x2

Identify and verify all of the included hardware

To begin, place the glass base (B1) on a flat surface

with the shiny side facing upwards. It is best if this

is located on a table, where the mounting holes are

able to hang just over the side.

Locate the following parts:

•Glass Base (B1)

•Two rear pedestals (B2)

•Metal top plate (B3)

•Rear bracket plate (B4)

•Two vertical bars (B5)

•Six clear vinyl self adhesive feet

•Eight plastic washers (A2)

•14 metal washers (A3)

•Six hex head screws (A4)

•Four philips head screws (A5)

•Four wing nuts (A6)

•Allen wrench (A7)

A1x6

B2x2

A4x2

A3x2

A2x4 A3x4 A4x4 A7

Place the glass base on a table, glossy side facing

downward.

Attach the self-adhesive feet, one near each corner,

one each centered along of the front and rear edge,

as shown.

Holding the base vertical, and laying the rear supports

on the table, attach the rear supports to the base as

shown, using (A2) plastic washers, (A3) metal washers

and (A4) hex head screws. Make sure the (A2)

washers are between the (A3) washers and the base.

Be certain that the mounting holes on the rear supports (B2)

are located at the top of the rail, as shown in illustration

#2 and #3.

Tighten the hex head screws with the supplied (A7) Allen

wrench. These should be quite snug but do not

over-tighten, as damage to the base may occur.

As mentioned on the previous page, it may be easier to

lay the glass base flat, with the holes over the edge of

a desk, and the (B2) rear supports positioned vertically.

Once attached, position the rear supports upright, and

attach the top mounting plate (B3) across the two (B2)

rear supports

Using the (A4) screws and (A3) metal washers, attach

the plate to the top of the (B2) supports as shown in

illustration #3. It may be necessary to loosen the lower

screws and tighten all four at the same time in order to

ensure the rear supports are straight.

A2x4A6x4

A3x4

A3x4 A5x4

Determine the optimum height on the rear pedestal to

attached the (B4) bracket. The best method to do this

is to measure from the center of your television screen

to the bottom most edge of the TV set. This will tell you

the minimum clearance needed on this Universal Base.

The vertical center of the (B4) bracket must be at least 1”

higher from the base than your measurement taken on

your television. This will ensure you have enough clearance

for proper ventilation. It is also important to consider any

TV controls, connections or attached cables that may

require clearance.

Locate four (A5) philips head screws and four (A3) metal

washers. Slide each washer onto the (A8) screw.

Attach the bracket (B4) to the rear pedestals by sliding

the four (A5) screws through the appropriate holes.

Make sure the bracket is horizontally centered.

The (A5) screws will protrude from the rear of the pedestal.

Slide first a plastic washer (A2) then metal washer (A3) onto

each of the screws. Then attach a wingnut (A6) to each of

the screws and tighten until snug.

B5x2

Locate the two television mounting brackets (B1).

These brackets attach to the rear mounting points on most VESA

standard television sets. These are compatible with VESA sizes

up to 600 x 400. Using the screws and washers provided, these

will attached to the rear of your television set. As all sets differ

slightly, it is not possible to provide exact instruction in this

document. If possible, you should refer to your television owner’s

manual for this.

Many different screw sizes are provided to accommodate most

every television in the market. The critical issue is to choose screws

that are the correct TPI (threads), diameter, and appropriate length.

Choosing a screw that is too short will cause the mount to not

support the set.

Choosing a screw that is too long may cause you to insert too

far into the rear of your set, thus damaging internal components.

Attach the (B5) brackets to the rear of your set and be certain all

screws are properly and securely inserted.

On the rear of the (B5) brackets, locate the attachment

set screws facing downward. These secure the television

to the assembled stand. Fully loosen these screws until

They are just in their threaded holes.

It is now time to hang the television onto the base.

This this will require two people.

Hook the top of the (B5) bracket on to the

assembled stand. The (B5) bracket will hang on the top lip of

the horizontal bracket, with the set screws tightening against the

bottom lip. Tighten the screws against the bottom lip and test

the set to make sure it is secure.

PRO SIGNAL 50-14797. Operating instructions

Brand: PRO SIGNAL

Model: 50-14797.

Type: Operating instructions

Download PDF

report

PRO SIGNAL 50-14797. Operating instructions

PRO SIGNAL 50-14797. Operating instructions

Related papers

Other documents