urban ambiance UQL1379 Installation guide

Type
Installation guide

Urban Ambiance UQL1379: This stylish light fixture is designed to enhance the ambiance of any room with its industrial bronze finish and vintage-inspired design.

Capabilities:

  • Accommodates two A19 Medium Base bulbs (60W maximum)
  • Recommended for use with Medium Base Vintage Bulbs (not included)
  • Adjustable nipple allows for customization of fixture height
  • Easy installation with clear instructions and required tools listed

Possible Use Cases:

  • Create a warm and inviting atmosphere in living rooms or bedrooms
  • Add a touch of industrial charm to lofts or workshops
  • Illuminate hallways or entryways with a unique and eye-catching fixture

Urban Ambiance UQL1379: This stylish light fixture is designed to enhance the ambiance of any room with its industrial bronze finish and vintage-inspired design.

Capabilities:

  • Accommodates two A19 Medium Base bulbs (60W maximum)
  • Recommended for use with Medium Base Vintage Bulbs (not included)
  • Adjustable nipple allows for customization of fixture height
  • Easy installation with clear instructions and required tools listed

Possible Use Cases:

  • Create a warm and inviting atmosphere in living rooms or bedrooms
  • Add a touch of industrial charm to lofts or workshops
  • Illuminate hallways or entryways with a unique and eye-catching fixture
1of2
Package Contents
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar
Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(2)A19MediumBasebulbs60WMaximum,MediumBaseVintageBulbsarerecommended,bulbsnotincluded.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
STEP 1 Install Glass Panel-
A. Place the Glass Panel (D) into the bottom of the Cage (C).
STEP 2 -Install the Crossbar Assembly to Outlet Box and Adjust
the length of the Nipple
A. Attach the Crossbar Assembly (A) to the Outlet Box with the head of
the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included), tighten until snug
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Remove the mounting ball from the nipple. Place the Fixture Body
(B) over the nipple against the ceiling to determine the correct
position of the nipple. Thread the mounting ball onto the nipple.
Adjust the nipple to allow the Fixture Body (B) to rest against the
ceiling when held in place by the mounting ball.
.
Hex Nut and
Lock Washer
Nipple
Green Ground Screw
Outlet Box Screw
(not included)
Mounting Ball
Figure 2
BFixture Body
x1
CCage
x1
DGlass Panel
x1
D
C
D
Figure 1
A
B
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Figure 3
(Step 2 Continued)
D. Remove the mounting ball and the Fixture Body (B). Tighten the lock
washer and the hex nut against the crossbar to secure in place.
Installation Instructions: UQL1379
www.urbanambiance.com
2of2
STEP 4 Install Ceiling Canopy to Crossbar-
A. Attach the Ceiling Canopy (CC) over the end of the nipple and
secure with previously removed mounting ball. Hand tighten until
snug.
B
Figure 4
Nipple
Mounting Ball
Vintage Bulb
(Recommended
but not included)
STEP 5 Install Bulbs and Cage-
A. Remove lock balls from bolts on the Fixture Body (B).
B. Insert bulbs onto sockets and screw snugly into place.
C. Attach the Cage (C) with glass panels over the bolts on the Fixture
Body (B) and secure with previously removed lock balls. Hand
tighten until snug.
Your fixture is now assembled and ready to use. Enjoy!
B
Figure 5
Bolt
C
Lock Ball
RO1612IZ
FINISH: INDUSTRIAL BRONZE
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
11.5
11.5
6”
www.urbanambiance.com
  • Page 1 1
  • Page 2 2

urban ambiance UQL1379 Installation guide

Type
Installation guide

Urban Ambiance UQL1379: This stylish light fixture is designed to enhance the ambiance of any room with its industrial bronze finish and vintage-inspired design.

Capabilities:

  • Accommodates two A19 Medium Base bulbs (60W maximum)
  • Recommended for use with Medium Base Vintage Bulbs (not included)
  • Adjustable nipple allows for customization of fixture height
  • Easy installation with clear instructions and required tools listed

Possible Use Cases:

  • Create a warm and inviting atmosphere in living rooms or bedrooms
  • Add a touch of industrial charm to lofts or workshops
  • Illuminate hallways or entryways with a unique and eye-catching fixture

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI