KingFisher ABW12P is a high-performance undercounter glass and dishwashing machine designed for commercial use. It offers a remarkable capacity, capable of cleaning up to 1200 glasses or 540 plates per hour, making it ideal for busy restaurants, bars, and catering businesses.
KingFisher ABW12P is a high-performance undercounter glass and dishwashing machine designed for commercial use. It offers a remarkable capacity, capable of cleaning up to 1200 glasses or 540 plates per hour, making it ideal for busy restaurants, bars, and catering businesses.
1
USER MANUAL
FOR KINGFISHER DELUXE
UNDERCOUNTER GLASS & DISHWASHERS
2
INTRODUCTION
Welcome to your new Kingsher Deluxe Warewasher.
This manual refers to more than one type of unit in the range. For reference, refer to the
product specications overleaf to identify your appliance.
Unpacking & Positioning
This appliance is not designed to be moved by hand from area to area. It must be moved into
position on a pallet with a forklift or other suitable lifting equipment before unboxing.
Upon unwrapping, inspect the machine for damage immediately. If any issues are noticed,
please contact the retailer directly.
Read this user manually carefully, particularly installation instructions overleaf before
attempting to use or operate the machine.
Safety Instructions
Do not use the appliance in areas without sucient lighting.
Do not touch moving parts of the appliance whilst it is in operation.
Do not install or use the appliance in the presence of ammable or explosive materials.
Do not operate the appliance when it is not connected to a water supply
This appliance must be earthed in accordance with local regulations. All damage caused by
use when not earthed will not be covered under the warranty.
If for any reason there is a malfunction of the appliance which causes a leak of water, ensure
that the electrical supply is switched o at the plug/circuit breaker immediately before
touching the appliance.
In the event of a malfunction of the appliance which causes re or smoke, switch o the
electrical supply at the plug/circuit breaker immediately. Do not use water to extinguish and
instead use a re extinguisher suitable for electrical res.
For further assistance, please call our UK service partner on 01279 876 500 or write an
email to [email protected]
3
PRODUCT SPECIFICATIONS
Technical Information
Model Dimensions (mm) Weight (kg)
A500KF13
490(W)x4500(D)x770(H) 48
ABW12P
590(W)x600(D)x820(H) 61
Product Code ABW12P A500KF13
Capacity 1200 glasses/hour 540 plates/hour
Basket Dimensions 400x400mm 500x500mm
Total Power 2.7kw 3kw
Motor Power 0.25kw 0.55kw
Boiler Heating 2.5kw 2.5kw
Tank Heating 1.8kw 2.5kw
Operating Voltage 230v 230v
Fuse Rating 13A 13A
Water Pressure 2-4 bar 2-4 bar
Program Timer 120 seconds
Drain Pump Yes Yes
120 seconds
4
INSTALLATION
All Kingsher Deluxe glass washers &
dishwashers are supplied with the following:
1. 3 Pin 13 amp UK Plug (Pre-Installed)
2. Drain Hose (Pre-Installed)
3. Water Inlet Hose (Not Installed)
4. Detergent Intake Pipe (Pre-Installed)
5. Rinse Aid Intake Pipe (Pre-Installed)
6. Two Baskets
7. Height Adjustable Feet (4)
Preparation For Start Up
Before installing or using the appliance, read this quick start user manual carefully. Incorrect
installation of the machine may damage the product, cause injury to people and invalidate your
warranty. The company is not responsible for damage to the appliance because of incorrect use,
negligence, wrong connections etc.
1. This instruction manual should be kept in a safe place for future reference
2. Installation should be made by a qualified service engineer
3. Please check for local regulations and rules about proper use & connection
4. The appliance is designed for commercial use & operation by trained personnel only
5. In the event of a malfunction or failure, turn off the appliance immediately
6. The appliance should only be repaired by authorised service personnel
For further assistance, please call our UK service partner on 01279 876 500 or write an
email to [email protected]
IMPORTANT
Please take care when unpacking the
unit. Ensure the height adjustable feet
are installed on to the unit BEFORE
moving to the installation location.
Once in place ensure unit is level, left to
right, front to back as if not this can
aect the running of the machine.
GENERAL INFORMATION
1. Open up the packaging and remove all protective film
2. Adjust the feet to ensure the appliance is level. Check with a spirit measure to ensure
level back to front and side to side
3. Connect the elbowed part of the water supply hose to the water inlet solenoid at the rear
4. Unwind the drainage hose and clamp the nearest waste outlet. Make sure the hose is not
kinked and water can flow freely. The hose should not bend more than 90 degrees
5. Incoming water pressure should be between 2-4 bars. If the water pressure is lower or
higher, then a pressure reducing valve or booster pump must be fitted
6. A water softener should be fitted to prevent limescale build up. Failure to do so could
invalidate your machine warranty
7. Turn on the water supply and visually check all connections to confirm there are no leaks
and everything is connected tightly
5
RECOMMENDED
All units will come supplied with electric automatic
chemical dosing pumps fitted internally to the
machine. The pickup for these are the two pipes at
the rear of the machine.
The pipes will be labelled RINSE and DETERGENT.
Ensure that they are routed to the correct type of
chemicals and insert the tube to the liquid.
Connecting Chemicals:
Connecting Power:
•Always allow the machine to heat up prior to the first use of the day. Check the temperature
ready indicator prior to washing.
•Before placing items into the basket, it is recommended that you pre-wash. Any solid waste
should be cleared first with a sprayer. Heavily baked on grease or debris should be soaked prior
to washing in the machine.
•Do not wash materials that are made of plastic. Check items are suitable for washing in a
commercial dishwasher at high temperatures first.
•We recommend the use of liquid detergents with a foam control agent. Failure to use the
correct detergents could cause improper wash results, excess foaming and damage to your
machine.
•If you are using an external water softener, we recommend that you regularly check it to ensure
that it has been regenerated and topped up with salt.
•To gain access to the components/controls such as the thermostat temperature controls,
simply remove the front panel. IMPORTANT: Before removing the panel, make sure that you
disconnect the electric supply.
•The thermal reset button is located to the left of the thermostat.
•The top thermostat is for the Boiler and the bottom thermostat switch is for the Tank. To adjust
the boiler temperature to the recommended 80°c, turn the switch 3/4 clockwise. To adjust the
tank temperature to the recommended 55-60°c, turn the switch half way clockwise.
Important Notice: The machine must be connected directly to a mains socket that is suitable
for an appliance which draws a maximum of 13 Amps. You must not use the appliance with an
extension lead or multi-way adapter, etc.
Further Remarks:
It is always advisable to make a small hole in the lid of the chemicals and feed the tube through,
you will need to remove the weight and filter before doing so, re attach this when the tube has
gone through the lid, screwing the lid back on to the chemical bottle. Ensure the chemical dosing
tube has been fed through, so it is at the bottom of the bottle. This is to prevent Oxidization of
the chemicals, provide longer shelf life and prevent air locks.
Wash results and machine
longevity can be highly dependant
on the quality of chemicals used.
Kingsher has been tested with
and always recommends the use
of EntirePro.
6
OPERATION
Control Panel Overview
1. Shut the door of the appliance
2. Press the power switch (A) to turn on the appliance
•The machine will take the water inside and begin heating it
•The water ready light (B) will turn on when the water reaches temperature
3. After the water ready light (B) has turned on, Press the wash cycle start button (C)
•The machine will then start the 2 minutes wash cycle
4. During the wash cycle, the washing light will remain on
•Once the wash cycle has finished, this light will switch off
5. To perform an additional manual rinse cycle:
Regular Maintenance
•When the water in the washing tank gets dirty, it must be replaced with fresh water. To do
this, switch the machine off and then follow step 6 above to drain the machine.
•We recommend that you regularly clean the washing and rinse nozzles to keep washing
results as good as possible. To do this, turn off the machine and disconnect the power.
Unscrew each of the nozzles and rinse them through with fresh water. Apply descaler if
required to remove any scale build up. Once cleaned, re-assemble all parts and refill the
machine.
•If an air lock occurs in the detergent or rinse aid pumps, press and hold the manual rinse
cycle button (step 5 above).
6. To drain the water after a working day:
•Hold the Manual Rinse button (D)
•Turn off the machine by pressing the power switch (A)
•Open the door and take out the drain pipe and keep the door open
•Press and hold the manual rinse switch (D) to drain the water
•Once finished draining, open the door and put the drain plug back in
EXPLODED SPARE PARTS DIAGRAM
Kingfisher Deluxe Glasswasher 400mm
NO PRODUCT NAME
01 DOOR 09 SIGNAL LAMP 17 FASCIA
02 HANDLE 10 ON/OFF SWITCH 18 PLASTICS
03 FOOT 11 ON/OFF SWITCH 19 RUBBER
04 SHAFT & SHAFT BEARING 12 TIMER M48 20 DOOR STOP
05 LOCK 13 CONTACTOR 21 HEATING ELEMENT
06 SWITCH 14 PRESSURE SWITCH
07 ARM 15 PRESSURE SWITCH CABLE
08 SWITCH 16 CONNECTOR
NO PRODUCT NAME NO PRODUCT NAME
7
EXPLODED SPARE PARTS DIAGRAM PG.2
Kingfisher Deluxe Glasswasher 400mm
NO DESCRIPTION NO DESCRIPTION NO DESCRIPTION
01 WASH PUMP 16 NOZZLE 31 HEATING ELEMENT BOILER
02 SHAFT 17 NUT 32 RINSE AID DISPENSER
03 SUCTION FILTER PIN 18 FLANGE 33 BOILER
04 AMPLIFIER 19 SUCTION FILTER 34 SOLENOID VALVE
05 SHAFT 20 SUCTION FILTER BOTTOM 35 RINSE ARM
06 BEARING 21 NUT 36 NOZZLE
07 GASKET 22 DRAINER 37 NUT
08 BODY 23 DRAIN PIPE 38 PLUG
09 BODY 24 LID 39 THERMOSTAT
10 ARM25 PRESSURE POT 40 LIMITER
11 TERMINAL 26 HOSE 41 CLIP
12 BOLT 27 HOSE 42 CLIP
13 FLANGE 28 HOSE 43 CLIP
14 FLANGE 29 HOSE 44 CLIP
15 NOZZLE 30 HOSE 45 CLIP
8
EXPLODED SPARE PARTS DIAGRAM
Kingfisher Deluxe Dishwasher 500mm
NO PRODUCT NAME
01 DOOR 09 SIGNAL LAMP 17 FASCIA
02 HANDLE 10 ON/OFF SWITCH 18 PLASTICS
03 FOOT 11 ON/OFF SWITCH 19 RUBBER
04 SHAFT & SHAFT BEARING 12 TIMER M48 20 DOOR STOP
05 LOCK 13 CONTACTOR 21 HEATING ELEMENT
06 SWITCH 14 PRESSURE SWITCH
07 ARM 15 PIPE FOR PRESSURE SWITCH
08 SWITCH 16 CONNECTOR
NO PRODUCT NAME NO PRODUCT NAME
9
Kingfisher Deluxe Dishwasher 500mm
NO DESCRIPTION NO DESCRIPTION DESCRIPTION NO DESCRIPTION
01 WASH PUMP
13
FLANGE 25 LID 37 NOZZLE
02 SHAFT 14 FLANGE 26 PRESSURE POT 38 NUT
03 SUCTION FILTER 15 NOZZLE 27 HOSE 39 NUT
04 AMPLIFIER 16 NOZZLE 28 HOSE 40 THERMOSTAT
05 SHAFT 17 NUT 29 HOSE 41 LIMITER
06 BEARING 18 NUT 30 HOSE 42 CLIP
07 GASKET 19 FLANGE 31 DRAIN HOSE 43 CLIP
08 BODY 20 FILTER 32 HEATING ELEMENT 44 CLIP
09 BODY 21 BOTTOM 33 RINSEAID DISPENSER CLIP
10 ARM 22 NUT 34 BOILER 46 CLIP
11 TERMINAL 23 DRAINER 35 SOLENOID VALVE
12 BOLT 24 DRAIN PIPE 36 ARM
EXPLODED SPARE PARTS DIAGRAM
NO
45
10
Kingfisher Deluxe Glasswasher 400mm
ELECTRIC CIRCUIT DIAGRAM
S1 - On/Off Switch
S2 - Pressure Switch
S3 - Programme Start Button
S4 - Manual Rinse Button
S5 - Lid Switch
S6 - Drain Pump Button
ST - Limit Thermostat (100°C)
TB - Boiler Thermostat
TT - Tank Thermostat
T - Timer
CB - Boiler Contactor (15A)
CT - Tank Contactor (9A)
HB - Boiler Heater
HT - Tank Heater
WP - Washing Pump
DP - Drain Pump
SV - Solenoid Valve
LO - On/Off Light
LR - Water Ready Light
LW - Washing Light
11
Kingfisher Deluxe Dishwasher 500mm
S1 - On/Off Switch
S2 - Pressure Switch
S3 - Programme Start Button
S4 - Manual Rinse Button
S5 - Lid Switch
S6 - Drain Pump Button
ST - Limit Thermostat
TB - Boiler Thermostat
TT - Tank Thermostat
T - Timer
CB - Boiler Contractor (9A)
CT - Tank Contractor (12A)
HB - Boiler Heater
HT - Tank Heater
WP - Washing Pump
DP - Drain Pump
SV - Solenoid Valve
LO - On/Off Lamp
LR - Water Ready Lamp
LW - Washing Lamp
ELECTRIC CIRCUIT DIAGRAM
12
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
KingFisher ABW12P is a high-performance undercounter glass and dishwashing machine designed for commercial use. It offers a remarkable capacity, capable of cleaning up to 1200 glasses or 540 plates per hour, making it ideal for busy restaurants, bars, and catering businesses.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Metos 151S Operating instructions
-
Washtech XP User manual
-
Thermo Fisher Scientific KingFisher Apex Purification System User guide
-
GGM Gastro GLSPME44 User manual
-
Classic ECO2 H500 User manual
-
Buffalo DW319 User manual
-
Meiko EcoStar 545 D Operating instructions
-
-
Fagor AD?120CW User manual
-
Insinger RL-30 User manual
