George Kovacs P8143-609-L User manual

  • Hello! I am an AI chatbot trained to assist you with the George Kovacs P8143-609-L User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
INSTALLATION INSTRUCTIONS
FOR P8143-609-L
FOR LED Chandelier/Pendant Light
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BRE AKE R.
AV E R T I S S E ME N T ! C O U P E R L E C O U R A N T A U N I V E A U D ES F U S I B L E S OU D O D I S J ON C T E U R
Page: 1/2
Fig. 2
HANGING THE FIXTURE
1. Carefully remove the fixture from the carton and check
that all parts are included as shown in the illustration.
2. Shut off power at the circuit breaker and remove old
fixture including the mounting hardware
SUGGESTED INSTALLATION (Fig. 1)
3. Attach the mounting plate (B) to the junction box (F)
using screws (D) (Screw Size: 8-32*1/2”L). The side of
the mounting plate marked “GND” must face out.
4. The support cable (N) is provided to support the weight
of the fixture while wiring. Attach the hook on support
cable (N) to the slot hole on the mounting plate (B).
Carefully allow the support cable (N) to support the
weight of the fixture while wiring.
CONNECTING THE WIRES (Fig. 2)
5. Connect the driver input wire with housing wire as
shown in Fig.2, making sure that all wire connectors
(C) are secured.
6. If your outlet box has a green or bare copper ground
wire, connect the fixture’s ground wire to it. Otherwise,
connect the fixture’s ground wire directly to the
mounting plate (B) using the green screw provided.
After wires are connected, tuck them carefully inside
the junction box (F).
COMPLETING THE INSTALLATION (Fig. 1)
7. Connect the canopy (A) with the mounting plate (B)
and secure with mounting screws (E).
8. Adjust the length of the cable to pull or push until the
desired length by pushing down the nod(G).
Your installation is now complete. Return power to the
junction box and test the fixture.
IMPORTANT: Fixture should be installed by a qualified electrician to
ensure proper wiring and installation.
Dimmable with ELV and/or LED compatible wall dimmer switches.
.
Fig.1
Set# A-021-197
- Mounting plate
- Ground screw
- Mounting screws*2pcs
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
White
(Neutral)
FIXTURE
WIRES
Bare
Copper
(Ground)
HOUSE
WIRES
Green
(Ground)
Fig.3
Page 2/2
Replacing LED module (Fig. 3&4)
The LED module can be replaced by a qualified
electrician without cutting of wire and without damage
to any decorative element to which the fixture is
attached.
a. Shut off power. Loosen screw (E) to disconnect
the canopy (A) from the mounting plate (B)
b. Disconnect the wire connectors (H) from the driver
and remove the protective rubber tube (L) on the
wire.
c. Loosen the wire clip (I).
d. Pushing down the nod (G) and pull the cable out.
e. Loosen screws (K) and metal clip (O) to
disconnect the aluminum ring (Q) (included LED
module) from the acrylic ring (P).
f. Reverse steps a-e for installing the new
aluminum ring (Q) and make sure that all wire
connectors (H) are secured and with electronic
tape for insulation. Connect the wires of the
largest aluminum ring to output wires from the
driver (L), as following middle aluminum ring to
driver (M) and the smallest aluminum ring to
driver (S) as shown in Fig.4
Note: The LED module should be provided by a
specified supplier.
Fig.4
/