George Kovacs P8143-609-L User manual

Brand: George Kovacs

Model: P8143-609-L

Type: User manual

George Kovacs P8143-609-L is a dimmable LED Chandelier/Pendant Light that can be installed on a ceiling. The chandelier/pendant light requires professional installation by a qualified electrician to ensure proper wiring and installation. It comes with a mounting plate, ground screw, and mounting screws to facilitate the installation. Additionally, a support cable is provided to support the weight of the fixture while wiring. The LED module can be replaced by a qualified electrician without cutting any wires or damaging any decorative elements.

INSTALLATION INSTRUCTIONS

FOR P8143-609-L

FOR LED Chandelier/Pendant Light

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BRE AKE R.

AV E R T I S S E ME N T ! C O U P E R L E C O U R A N T A U N I V E A U D ES F U S I B L E S OU D O D I S J ON C T E U R

Page: 1/2

Fig. 2

HANGING THE FIXTURE

1. Carefully remove the fixture from the carton and check

that all parts are included as shown in the illustration.

2. Shut off power at the circuit breaker and remove old

fixture including the mounting hardware

SUGGESTED INSTALLATION (Fig. 1)

3. Attach the mounting plate (B) to the junction box (F)

using screws (D) (Screw Size: 8-32*1/2”L). The side of

the mounting plate marked “GND” must face out.

4. The support cable (N) is provided to support the weight

of the fixture while wiring. Attach the hook on support

cable (N) to the slot hole on the mounting plate (B).

Carefully allow the support cable (N) to support the

weight of the fixture while wiring.

CONNECTING THE WIRES (Fig. 2)

5. Connect the driver input wire with housing wire as

shown in Fig.2, making sure that all wire connectors

6. If your outlet box has a green or bare copper ground

wire, connect the fixture’s ground wire to it. Otherwise,

connect the fixture’s ground wire directly to the

mounting plate (B) using the green screw provided.

After wires are connected, tuck them carefully inside

the junction box (F).

COMPLETING THE INSTALLATION (Fig. 1)

7. Connect the canopy (A) with the mounting plate (B)

and secure with mounting screws (E).

8. Adjust the length of the cable to pull or push until the

desired length by pushing down the nod(G).

Your installation is now complete. Return power to the

junction box and test the fixture.

IMPORTANT: Fixture should be installed by a qualified electrician to

ensure proper wiring and installation.

Dimmable with ELV and/or LED compatible wall dimmer switches.

Fig.1

Set# A-021-197

- Mounting plate

- Ground screw

- Mounting screws*2pcs

FIXTURE

WIRES

Black or

Smooth

HOUSE

WIRES

Black

(Hot)

FIXTURE

WIRES

White or

Ribbed

HOUSE

WIRES

White

(Neutral)

FIXTURE

WIRES

Bare

Copper

(Ground)

HOUSE

WIRES

Green

(Ground)

Fig.3

Page 2/2

Replacing LED module (Fig. 3&4)

The LED module can be replaced by a qualified

electrician without cutting of wire and without damage

to any decorative element to which the fixture is

attached.

a. Shut off power. Loosen screw (E) to disconnect

the canopy (A) from the mounting plate (B)

b. Disconnect the wire connectors (H) from the driver

and remove the protective rubber tube (L) on the

wire.

c. Loosen the wire clip (I).

d. Pushing down the nod (G) and pull the cable out.

e. Loosen screws (K) and metal clip (O) to

disconnect the aluminum ring (Q) (included LED

module) from the acrylic ring (P).

f. Reverse steps a-e for installing the new

aluminum ring (Q) and make sure that all wire

connectors (H) are secured and with electronic

tape for insulation. Connect the wires of the

largest aluminum ring to output wires from the

driver (L), as following middle aluminum ring to

driver (M) and the smallest aluminum ring to

driver (S) as shown in Fig.4

Note: The LED module should be provided by a

specified supplier.

Fig.4

George Kovacs P8143-609-L User manual

Brand: George Kovacs

Model: P8143-609-L

Type: User manual

Download PDF

report

George Kovacs P8143-609-L User manual

George Kovacs P8143-609-L User manual

Related papers

Other documents