ITEM# I-I-37003
Assembly Instructions
Model # 37003
www.eastpoi ntsports.com
TWO OR MORE ADULTS REQUIRED FOR ASSEMBLY
I TA FETY INSTRUCTI
1,
2,
3,
4,
S,
6,
7,
8,
9,
10,
11,
12,
Read all instructions - All the safety and operating instructions should be read carefully before this Hover
Hockey table can be operated or played.
Caution - This is not a toy and is intended for use by or under the supervision of adults. Adults should
review safety guidelines with children to avoid possible risk of electric shock or other injuries.
Caution - This table rotates on a central axis and can pose a small risk of a pinch hazard. Keep hands
clear when swivel cabinet is in motion.
Power Sources - This Hover Hockey game should be operated only from 100-12SV A.C., 50/60 cycle current
as indicated on the identification label. Ifyou are not sure of the type of power supply to your home,
consult your appliance dealer or local power company.
Power Cord Protection - Power cord should be routed so that it is not likely to be walked on or pinched
by items placed upon or against it. Pay particular attention to cords at plugs, convenience receptacles,
and the point of exit from the game.
Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or
electric shock.
Object and Liquid Entry - Never push objects of any kind into this game through openings as they may
touch dangerous voltage points or short-out parts which could result in a fire or electric shock. Never spill
liquid of any kind on the game. If cleaning the surface, follow the recommended manufacturer instructions
or call technical support for guidance.
Ventilation - Openings in the game are provided for the exhaust air to create a cushion/floating effect.
The openings on the air blower are for the intake air. Keep clear of the air blower during operation.
Do not allow hand, hair, or any other objects near the intake openings. To ensure reliable operation of
the game and protect it from overheating, these openings must not be blocked or covered.
Damage Requiring Service - Unplug the game from the wall outlet/receptacle. Do not attempt to service
the blower yourself as while opening and/or removing covers may expose you/others to dangerous voltage
or other hazards. Refer servicing to qualified service personnel under the following conditions:
a. When the power supply cord is damaged.
b. If liquid has spilled, or objects have fallen into the blower.
c. When the air blower exhibits a distinct change in performance - i.e. abnormal noise,
too much/too little air flow, this indicates a need for service
Grounding or Polarization - This game is equipped with a polarized alternating current line plug (a plug
having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace your obsolete outlet. DO NOT defeat the safety purpose of
the polarized plug.
CAUTION - ELECTRICALLY OPERATED PRODUCT - Not recommended for children under 8 years of age.
As with all electrical products, precautions should be observed during handling and use to reduce the
risk of electric shock.
We recommend - that the game be periodically examined for conditions that may result in the risk of fire,
electrical shock, or injury to persons. In the event such conditions exist, the game should not be used
until properly repaired.
13, Storage Conditions - This product is made from wood based components and is sensitive to extreme
temperatures and moisture / humidity. Subject to these conditions will effect game play, cosmetics
and longevity.
SaveT ese I ST CTI
Warn i n g _To Reduce The Risk Of Fire Or Electric Shock, Do Not UseThis Fan With Any Solid-State Speed Control Device
m m
Lay out al parts before you begin
- Please review the parts identifier and make sure that you have all parts before beginning assembly.
If any questions or issues, please contact us at 1-973-585-4747 BEFORE returning the product to the original place
of purchase.
• Please keep your original sales receipt. Staple it on the adjacent page in the space provided for future reference/use.
It will be required to receive service help or parts under warranty.
(9:00am to 5pm EST)
Technical Support or Replacement Parts
Visit us at: www.eastpointsports.com
Call: 973-585-4747
UIL G -
ease inspect your piayfiel
Your Cabinet (holds Billiard table and Hockey Playfield) is NOT replaceable. Any damage that exists to
your playfield is not reparable under warranty. If your play6eld is damaged, the entire game must be
returned to the original place of purchase for an exchange.
IP ...................... =11
I I
I I
ease attac
= IPT E =
I I
It will be required to receive service help or parts under warranty.
I I
I I
L ...................... =11
3
TOOLS
Required
• 1 - Phillips Head Screwdriver
(Standard Size) - Not Included
• 1 - HexWrench- Included
• 1 - Allen Wrench - Included
• Electric Screwdriver or Power Driver
CAUTION - DO NOT OVER TIGHTEN. OverTightening
will result in irreparable damage to the product. If using,
please make sure that the tool is set to a very low torque
to prevent damage to the product.
• Socket Wrench Set
TI I
How to use the:
Before you begin assembly, please make sure that
you have all the parts listed and in the correct
quantities. This will ensure the quickest and most
organized assembly.
Be sure to work on the assembly on a soft
non-marring surface such as carpet or the inside of
the corrugate box top to prevent causing damage
to the table surface during assembly.
Instructions Parts ID #
(_._ ,.. Part Name
J Part Name''
Item #"
"Step Used In
-Part Image
Part Quantity
TI I
9_)Cabinet - Billiards
..
_ron -End Board
# 37003-02S
)ton - Long Side Leg- Right (_ _Leg - Left _TI
jr
# 37003-01S # 37003-045 # 37003-035 _ [_
[
4
Components cont.
_ _ Leg Leveler
2_Lock Pin
Panel- Inner-
# 37003-05S
Panel- Inner-
# 37003-06S
(_') Ball Channel - End
Panel - Outer -
# 37003-08S
End Panel-Outer-
Non-Return End
(_ Goal Panel- Left
# 37003-10S
I
_Goal Panel - Right
_Goal Panel- Bottom
3_ Apron - Cabinet Side _End Rail - Top
_Cup Holder {_
0_ Pusher - Felt _ Pusher - Sombrero
......................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................i
Components cont.
Tennis Top - 3pc - Center
# 37003-15S
Q
b Post - TT
1
b Tennis Top - 3pc - End
b Net- TT
J
# 37003-19S
Tennis Top - Support
# 37003-17S
l_) Tennis Top - Cushion
Accessories
Billiard Balls
000
0000
0000
0000
Billiard Cue
c
I Paddle -T__)
# 37003-22S
Brush
BiNiard Chalk
# 37003-27S
Ball -TT
Triangle - Molded
Hockey Puck
(
_4_Screw-Wood-4x44,5mm
_Bolt- Allen-8x44,5mm
'0_ Bolt-Hex- 20mm
(1pcpre-assembled)
#37003-705
_Bolt- Allen-8x44,5mm
# 37003-615
_5_Screw-Wood-4x44,5mm
#37003-605
( _9_Screw-Wood-4x 32ram
7_Washer -Metal-20mm
(1pcpre-assembled)
6_Wrench -AllenStyle
# 37003-625
6_Bolt - Allen- 6,5x 32mm
#37003-665
)3_ Screw-Wood-4x18mm
Screw-Wood-4x44,5mm
#37003-715
7_Washer- Molded- 20mm
(1pcpre-assembled)
Hex
#37003-725 #37003-735
_ '4_Screw-Wood-4x18mm
[
7
BEFORE ")
LY INSTRUCTI
BEFORE BUILDING-
Please inspect your playfieid
and layout all your parts
Your Cabinet (holds Billiard table and Hockey
Playfield) is NOT replaceable. Any damage that
exists to your playfield is not reparable under
warranty. If your playfield is damaged, the entire
game must be returned to the original place of
purchase for an exchange.
®
0 D_ 0
G Cabinet- Hockey |
(_ Cabinet- Billiards F_
Open cabinet.
Take out all
parts and
remove brace
/Table Tennis
Top.
::)utside "Inside
I _I tl ¸
Q Apron-Long Side E_
Q Apron- End Board E_
0 Screw-Wood-4 x44.5mm |
Repeat for
both sides.
8
Step2Assembly
I Dill • I!
QLe0-Left
C)Le0-R,0ht
@ Leg Leveler r-_
step 2 Assembly |
Q Bolt-Allen-8x44.5mm F_
@ Wrench-AllenStyle F_
Repeat for
Both Sides.
Ball Return End Non-Ball Return End
v v
( STEP 5A _ rk_ STEP 5B
Ball Return End Non-Ball Return End
Step 4A Assembly
i
I
t
Step 4B Assembly
I DO II! •
Q nd Panel - Inner- |
Return End
Q End Panel-Inner- |
Non-Return End
@ Lock Pin
@ Screw-Wood-4x18mm
tt DO • • I! •
Q Ball Channel- End F_
Step 4A Assembly F_
step 4B Assembly
Q Screw-Wood-4x44.5mm F_
Do Not
Over Tighten.
STEP 6A_
BallReturnEnd
@
@
"_ STEP 6B "_
,. J
Non-Ball Return End
Step 5A Assembly
Step 6A Assembly
STEP 7B._____._._.__
Step 5B Assembly
Step 7A Assembly
( STEP 8 "_/
Step 7A
Assembly
Step 7B Assembly
Step 3
Assembly
Step 7B
Assembly
Q End Panel- Outer-Return End r_
End Panel - outer -
Non-Return End
Goal Panel- Left
Q Fq
®
©
pq
Goal Panel- Right
Goal Panel- Bottom
@ Screw-Wood-4 x44.5mm
O B01t-Allen-6.5x32mm F_
O De O
Step 5A Assembly r_
step 5B Assembly r_
step 6A Assembly r_
step 6B Assembly r-_
_llt _l ¸ i ¸
Q Screw-Wood-4x44.5mm
I DO 0
Step 3 Assembly F_
Step 7A Assembly
Step 7B Assembly
0 Bolt-Allen-8x44.5mm F_
Install parts
lOand 11
before installing
part 12.
Be Sure To
Install 5 Bolts
Into Each Leg.
10
(_ STEP9 ")
<-" - ..... 1 41 i
O Dt tt ¸
G Cabinet- Hockey |
(_ Cabinet- Billiards |
Q Screw-Wood-4x32mm ®
Make sure that
Billiard Cabinet
is completely
seated and
flush before
installing
Screws.
_l_ll Non-Ball Return Side
j,
Ball Return Side_
II DO O
Step 9 Assembly |
_IT _ tt ¸
Bolt- Hex-20mm
Q (1pcpre-assembled) ®
Washer-Metal-20mm
(1pcpre-assembled) F_
Washer-Molded- 20ram
(1pcpre-assembled)
@ Wrench-Hex r_
Side with
Electrical Cord
pre-assembled.
STEP 11
I DO tt ¸
Step 8 Assembly
Step 10 Assembly
1,UsingTwo
StrongAdults,
orientPlayfleld
Cabinetin proper
directionasper
drawing.
2.Gentlyset
Cabinetintoframe
beingcarefulnot
todamage
electricalcord.
3,ThreadCordas
perDrawing
11
@
O "0 O
@ Apron- Cabinet Side F_
Step 11 Assembly r_
Shows View from Inside
Q DI I
® Eo_Ro,,-XopF_
Step 12 Assembly r_
Q Screw-Wood-4 x 18mm
You will use 6
Screws per end
(4 inside and 2
outside).
STEP 14
® Cop,--,o,der F_
(_ STEP 15")
®
t DO t0
® Posher-Fe,t
Q Pusher- Sombrero E_
STEP 16
STEP 16A
"x
J
O DO 0
G Tennis Top- 3pc- CenterF_
Q TennisTop-3pc- End E_
Q Tennis Top- Support ®
G P°st-TT E_
G Net-TT ['_
Q Tennis Top- Cushion E_
Do Not
applythe
Cushions first.
Make sure
that they
align properly
with the top
aprons before
application.
TableTennis
Top should
only be set in
place when
Hover Hockey
playfield is
facing up.
13
iii_iii_!JiI!iiI!iiI!iiI!iiI!iiI!iiI!iiI!iiI!iiI!iiI!Jiii!!iiii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_i_¸i_i
Lira" rranty
Asdescribedin andaslimitedbythisLimitedWarranty,EastPointSports,Ltd.(the"Company")warrantsthisSwivelTable(the"Product")tobefreefromdefectsin
workmanshipandmaterialsfor aperiodof90daysfromthedateoforiginalpurchase.Thetermdefectsshallmeananyimperfectionsthat impairtheuseoftheproduct.
TheCompanyreservestherighttorequestconfirmationofProofofPurchasewhenrequestingpartsorserviceinordertoconfirmthat thegameiswithinitswarrantyperiod.
What is Covered: Exceptasprovidedherein,thisLimitedWarrantycoversalldefectsinmaterialsandworkmanship.ThisLimitedWarrantyisvoidiftheProductis:
Damagedthroughimproperusageorstorage,negligence,misuse,abuse,transportationdamage,actsofnature,oraccident(includingfailuretofollowthe
instructionssuppliedwiththeproduct)
Usedincommercialapplications,rentalsoracommercialenvironment
ModifiedorrepairedbyanyonenotauthorizedbytheCompany
What is Not Covered:
TheLimitedWarrantydoesnotcover:
Expendableitemssuchascosmeticparts,gameplayingaccessories,andanyotheritemsthatmayshowsignsofwearduetonormalusage
Anytransportation/delivery/installationcostsincurredbytheConsumer(eitherhomefromtheoriginalplaceofpurchaseorbacktotheoriginalplaceofpurchase)
What the Company Wiil Pay For:
IfanypartorcomponentoftheProductwhichiscoveredbythisLimitedWarrantyisfoundbytheCompanytobedefective,theCompanywill providereplacement
partswithoutcharge.TheCompany'sobligationtorepairorreplacetheProductoranyportionthereof,shahbelimitedtotheoriginalpurchasepriceoftheproduct.
IfduringtheLimitedWarrantyperiod,theproductisfoundtobedefective,theCompanywill,attheCompany'soption,repair,replace,ormakeremunerationforthe
Product(eitherthesameorequivalentvalue)withoutcharge.
How to Obtain Warranty Service: InordertoenforceyourrightsunderthisLimitedWarranty,youmustfollowtheseprocedures:
YoumustreturntheORIGINALCOPYOFYOURSALESRECEIPTtotheCompany.
YoumustcalltheCompany'sConsumerServiceDepartmentat1-973-585-4747ortoll freeat1-877-279-7071onMondaythroughFridaybetweenthehoursof9:00
A.M.and5:00P.M(EST)to notifytheCompanyofthenatureoftheproblem.AttheCompany'soption,replacementpartsoranewProduct(eitherthesameor
equivalentvalue)will besenttoyouatnocharge.
Ifyouareinstructedtoreturnthe ProducttotheCompanyforservicing,youareresponsibleforshippingtheProduct,atyourexpense,totheaddressdesignated
bytheCompanyin packagingthatwill protectagainstfurtherdamage.
Youmustalsoincludeyourname,address,daytimetelephonenumber,Productmodelnumber,andadescriptionofthe problem.
TheCompanywii[payforanyshippingchargestoreturntherepairedofreplacedProducttoyou.
THISLiMiTEDWARRANTYISAVAILABLEONLYTOTHEORIGINALPURCHASEROFTHEPRODUCTANDISVALIDONLYINTHEUNITEDSTATES.THECOMPANY'S
LIABILITYISLIMITEDTOTHEREPAIR,REPLACEMENT,ORREMUNERATION,ATITSOPTION,OFANYDEFECTIVEPRODUCTANDSHALLNOTINCLUDEANYLIABILITY
FORINDIRECT,INCIDENTAL,ORCONSEQUENTIALDAMAGESOFANYKIND.THISWARRANTYISEXPRESSLYMADEIN LIEUOFALLOTHERWARRANTIES,EXPRESSED
ORIMPLIED,INCLUDINGBUTNOTLIMITEDTOTHEIMPLIEDWARRANTYOFMERCHANTABILITYANDTHEIMPLIEDWARRANTYOFFITNESSFORAPARTICULAR
PURPOSE.SOMESTATESDONOTALLOWLIMITATIONSONHOWLONGANIMPLIEDWARRANTYLASTSORDONOTALLOWFOREXCLUSIONOFINCIDENTALOR
CONSEQUENTIALDAMAGES.TOTHATEXTENT,THEABOVELIMITATIONSMAYNOTAPPLYTOYOU.
ThisLimitedWarrantygivesyouspecificlegalrights,butyoumayalsohaveotherrightsthat varyfromstatetostate.
Ifyouhaveanyquestionsregardingthis LimitedWarrantyortheoperationofthe Product,youmaycallorwriteus.
ALLWARRANTYCLAIMSMUSTBEACCOMPANIEDBYA COPYOFTHESALESRECEIPT/PROOFOFPURCHASE.REPORTANYDEFECTSTO:
EASTPOINT
S P 0 l{ T S
628 ROUTE 1O,SUITE #5 WHIPPANY, NEW JERSEY 07981 • 1-973-585-4747
[ [? ?
14
,!
Table Top -
• It is OK to gently vacuum the felt side of the billiard table with any standard handheld vacuum brush
attachment.
• If Hockey or Table Tennis side needs to be cleaned, you can use any gentle surface cleaner (no bleach or
ammonia) with a lint free cloth.
NOTE: DO NOT spray the cleaning product directly on the table surface. It must be applied to the cloth
directly. Then the table top can be wiped in a lengthwise direction
Pucks -
• If a puck isrough or not gliding smoothly on top of the table surface, gently sand off the scuff marks with
fine grit sandpaper.
Speed -
• If faster puck speed isdesired, it isOK to use a wax or oil based cleaner to"slicken"the surface.
NOTE: DO NOT OVER APPLY. A little goes a long way.
NOTE: DO NOT spray the cleaning product directly on the table surface. It must be applied to
the cloth directly and then the table top can be wiped in a lengthwise direction.
EASTPOINT
S P O R T S
www.eastpoi ntsports.com
628 ROUTE 10, SUITE #5 WHIPPANY, NEW JERSEY07981 • 1-973-585-4747
/
