EastPoint Sports 1-1-37001 Installation guide

Type
Installation guide

This manual is also suitable for

ITEM# 1-1-37001
Crenr Cnrnes in l - dgrnn opciones dejuno
Assem ly
odel
www.eastpoi ntsports.com
TWO OR MORE ADULTS REQUIRED FOR ASSEMBLY
I TA FETY INSTRUCTI
1,
2,
3,
4,
S,
6,
7,
8,
9,
10,
11,
12,
Read all instructions - All the safety and operating instructions should be read carefully before this Hover
Hockey table can be operated or played.
Caution - This is not a toy and is intended for use by or under the supervision of adults. Adults should
review safety guidelines with children to avoid possible risk of electric shock or other injuries.
Caution - This table rotates on a central axis and can pose a small risk of a pinch hazard. Keep hands
clear when swivel cabinet is in motion.
Power Sources - This Hover Hockey game should be operated only from 100-12SV A.C., 50/60 cycle current
as indicated on the identification label. Ifyou are not sure of the type of power supply to your home,
consult your appliance dealer or local power company.
Power Cord Protection - Power cord should be routed so that it is not likely to be walked on or pinched
by items placed upon or against it. Pay particular attention to cords at plugs, convenience receptacles,
and the point of exit from the game.
Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or
electric shock.
Object and Liquid Entry - Never push objects of any kind into this game through openings as they may
touch dangerous voltage points or short-out parts which could result in a fire or electric shock. Never spill
liquid of any kind on the game. If cleaning the surface, follow the recommended manufacturer instructions
or call technical support for guidance.
Ventilation - Openings in the game are provided for the exhaust air to create a cushion/floating effect.
The openings on the air blower are for the intake air. Keep clear of the air blower during operation.
Do not allow hand, hair, or any other objects near the intake openings. To ensure reliable operation of
the game and protect it from overheating, these openings must not be blocked or covered.
Damage Requiring Service - Unplug the game from the wall outlet/receptacle. Do not attempt to service
the blower yourself as while opening and/or removing covers may expose you/others to dangerous voltage
or other hazards. Refer servicing to qualified service personnel under the following conditions:
a. When the power supply cord is damaged.
b. If liquid has spilled, or objects have fallen into the blower.
c. When the air blower exhibits a distinct change in performance - i.e. abnormal noise,
too much/too little air flow, this indicates a need for service
Grounding or Polarization - This game is equipped with a polarized alternating current line plug (a plug
having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should
still fail to fit, contact your electrician to replace your obsolete outlet. DO NOT defeat the safety purpose of
the polarized plug.
CAUTION - ELECTRICALLY OPERATED PRODUCT - Not recommended for children under 8 years of age.
As with all electrical products, precautions should be observed during handling and use to reduce the
risk of electric shock.
We recommend - that the game be periodically examined for conditions that may result in the risk of fire,
electrical shock, or injury to persons. In the event such conditions exist, the game should not be used
until properly repaired.
13, Storage Conditions - This product is made from wood based components and is sensitive to extreme
temperatures and moisture / humidity. Subject to these conditions will effect game play, cosmetics
and longevity.
SaveT ese I ST CTI
Warn i n g _To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device
m m
Lay out al parts before you begin
- Please review the parts identifier and make sure that you have all parts before beginning assembly.
If any questions or issues, please contact us at 1-973-585-4747 BEFORE returning the product to the original place
of purchase.
Please keep your original sales receipt. Staple it on the adjacent page in the space provided for future reference/use.
It will be required to receive service help or parts under warranty.
(9:00am to 5pm EST)
Technical Support or Replacement Parts
Email us at: [email protected]
Visit us at: www.eastpointsports.com
Call: 973-585-4747
UIL G -
ease inspect your piayfiel
Your Cabinet (holds Billiard table and Hockey Playfield) is NOT replaceable. Any damage that exists to
your playfield is not reparable under warranty. If your play6eld is damaged, the entire game must be
returned to the original place of purchase for an exchange.
IP ...................... =11
I I
I I
ease attac
= IPT E =
I I
It will be required to receive service help or parts under warranty.
I I
I I
L ...................... =11
3
TOOLS
Required
1 - Phillips Head Screwdriver
(Standard Size) - Not Included
1 - HexWrench- Included
1 - Allen Wrench - Included
Electric Screwdriver or Power Driver
CAUTION - DO NOT OVER TIGHTEN. OverTightening
will result in irreparable damage to the product. If using,
please make sure that the tool is set to a very low torque
to prevent damage to the product.
Socket Wrench Set
How to use the:
TSI TI I
Before you begin assembly, please make sure that
you have all the parts listed and in the correct
quantities. This will ensure the quickest and most
organized assembly.
Be sure to work on the assembly on a soft
non-marring surface such as carpet or the inside of
the corrugate box top to prevent causing damage
to the table surface during assembly.
Instructions Parts ID #
,_ .". Part Name
-'/Part Name""
. 2oooo-oo..
Item #"
%
"Step Used In
-Part Image
Part Quantity
TI I
Components
Panel -Left - A
# 37001-02S
_Leg Panel - Left - B
"L_
J Leg Panel - Right - A
(_ _ Leg Panel- Right- B (_)Z_)Leg Cap - Left _ ,"L_
-'/Leg Cap - Right
4
Components cont.
(_ _ Leg Leveler
Y
7_)Lock Pin
Leg Pedestal
_Ball Catcher Box
_2_-_ •.,
}_) Ball Board - Lower
_2T°°_-°_ .., _
_Leg - End Panel
Bali Board-Lower
3_Leg - Side Panel
(
J Table Top -Cabinet
_Top End Panel 5_ Hockey Scorer
_Cue Hook
(_ _) Pusher Felt _ ]_) Pusher- Sombrero
[
Hardware
(
_0_Screw-Wood-4x44,5mm
[_XXXXX\--_
#37001-605 xl 6
_1_Screw-Wood-4x25mm 2_ Screw-Wood-3x15mm (_ Screw-Wood-4x44,5mm
XXX\\_
Bolt-Allen-8x32mm
#37001-64S
Wrench-AllenStyle
# 37001-655
-_ Screw-Wood-4x44,5mm
\ \ \ \ \"c3:>
Screw-Wood-4x12mm
_ Screw-Wood-4x44,5mm (_9_Barrel Nut-Smm
# 37001-695
7_Bolt -HexHead-8x63,5mm
#37001-70S
7_Washer- Metal-8mm
©
#37001-71S
_ Bolt-Hex- 12mm
#37001-725
7_Washer -Metal-12mm
©
#37001-73S
7_Washer- Molded- 12mm
©
#37001-74S
Hex
#37001-75S
_'_ Screw-Wood-4x44,5mm
)\ \ \ \ \",,_3:>
[
6
Accessories
Triangle- Molded
BilliardBallSet
0000
0000
0000
0000
Table Tennis Playfield
Billiard Cue Billiard Chalk Foam Football
%
Hover Hockey Puck
Football Goal Net - Table Tennis
Post - Table Ten nis Paddle - Table Tennis Ball - Table Tennis
©
Brush
7
BEFORE ")
LY INSTRUCTI
BEFORE BUILDING-
Please inspect your playfieid
and layout all your parts
Your Cabinet (holds Billiard table and Hockey
Playfield) is NOT replaceable. Any damage that
exists to your playfield is not reparable under
warranty. If your playfield is damaged, the entire
game must be returned to the original place of
purchase for an exchange.
LEFT
o
( ®
RIGHT
l DI
Q Leg Panel- Left- A E_
Q Leg Panel- Left- B E_
_eo_one,-_,O,_-_E_
Q Screw-Wood-4 x44.5mm F_
Repeat for
all 4 legs.
(
STEP 2 "_
/
e
o
LEFT _
J_
o
o
o
o RIGHT
t DO 0
Q Le0Cap-Left r_
© LeoCap-R,O,t r_
Q Leg Leveler ®
Fq
Step 1 Assemblies
@ Screw-Wood-4x25mm 1-_
Repeat for
all 4 legs.
8
_[ STEP 3
O DO O
©_ock.,n I
Q Leg Pedestal r_
0 Screw-Wood-3x15mm |
Repeat for
both ends.
Do not
overtighten.
(4)
S'
Step 3 Assembly FLIP OVER FOR NEXT STEP
DO 0
Q Ball Catcher Box E_
Q Ball Board- Lower E_
Step 3 Assembly E_
Q Screw-Wood-4 x44.5mm |
Repeat for
both ends.
When
complete,
flip over.
STEP5
Step 4 --
Assembly
Step 2 Assemblies
I DO tl
Step 2 Assembly r-_
step 4 Assembly E_
Q Bolt-Allen-8x 32mm [-_
@ Wrench-AllenStyle F_
Repeat for
both ends.
STEP 6 ")
0 DI 0
@ Leg- End Panel
@ Ball Board- Lower E_
0 Screw-Wood-4x44.5mm E_
Repeat for
both ends.
(. 7 )
Step 6
Assembly
Step 5 Assembly
STEP 8
Step 7
Assembly
/
II De !I
Step 5 Assembly E_
Step 6 Assembly E_
,"11 _D 0
Q Screw-Wood-4x 12mm E_
I DO 0
Step 7 Assembly F_
0 Screw-Wood-4x44.5mm E_
Repeat for
both ends.
Repeat for
both ends.
10
semblies\
Step8 Assembly
Leg- Side Panel
Q BarrelNut- 8turn
Q BoIt- RexHead-8x 63.Smrn
Washer-Metal- 8mrn
Make SUre hole
in barrel nut is
facing the bolt.
Otherwise it
will not go in
all the way.
Repeat for
both sides.
s
Q TableTop-Cabinet
Repeat for
both ends.
f
;!
STEP 11
Step 10Assemb
tep 9 Assembly
Bolt-Rex-12turn
@ Washer-_#etal-12rnrn
Q Washer-Molded_72m
Wrench-Hex
Step 9Assembly
Step 10Assembly
Besuretodoit
evenly.
Whencomplete,
engageall4 Lock
Pins,
11
(
tll DO t
Step 1 1 Assembly
Q Top End Panel F_
Q Screw-Wood-4x44.5mm
Repeat for
both ends.
Do not over
tighten.
0 _0 0
Step 12 Assembly
@ Hockey Scorer F_
Q Cue Hook F_
To complete
this step, the
hockey side
must be
facing up.
If not,
disengage all
4 Lock Pins,
Swivel, then
re-engage all
4 Lock Pins.
( STEP14"_/
DO
@ Pusher- Sombrero
Peel back felt
and apply
evenly to
bottom of
Pushers.
iii_iii_!JiI!iiI!iiI!iiI!iiI!iiI!iiI!iiI!iiI!iiI!iiI!Jiii!!iiii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_ii!i!_i_¸i_i
Lira" rranty
Asdescribedin andaslimitedbythisLimitedWarranty,EastPointSports,Ltd.(the"Company")warrantsthisSwivelTable(the"Product")tobefreefromdefectsin
workmanshipandmaterialsfor aperiodof90daysfromthedateoforiginalpurchase.Thetermdefectsshallmeananyimperfectionsthatimpairtheuseoftheproduct.
TheCompanyreservestherighttorequestconfirmationofProofofPurchasewhenrequestingpartsorservicein ordertoconfirmthat thegameiswithinitswarrantyperiod.
What is Covered: Exceptasprovidedherein,thisLimitedWarrantycoversalldefectsinmaterialsandworkmanship.ThisLimitedWarrantyisvoidiftheProductis:
Damagedthroughimproperusageorstorage,negligence,misuse,abuse,transportationdamage,actsofnature,oraccident(includingfailuretofollowthe
instructionssuppliedwiththeproduct)
Usedincommercialapplications,rentalsoracommercialenvironment
ModifiedorrepairedbyanyonenotauthorizedbytheCompany
What is Not Covered:
TheLimitedWarrantydoesnotcover:
Expendableitemssuchascosmeticparts,gameplayingaccessories,andanyotheritemsthatmayshowsignsofwearduetonormalusage
Anytransportation/delivery/installationcostsincurredbytheConsumer(eitherhomefromtheoriginalplaceofpurchaseorbacktotheoriginalplaceofpurchase)
What the Company Wiil Pay For:
IfanypartorcomponentoftheProductwhichiscoveredbythisLimitedWarrantyisfoundbytheCompanytobedefective,theCompanywill providereplacement
partswithoutcharge.TheCompany'sobligationtorepairorreplacetheProductoranyportionthereof,shahbelimitedtotheoriginalpurchasepriceoftheproduct.
IfduringtheLimitedWarrantyperiod,theproductisfoundtobedefective,theCompanywill,attheCompany'soption,repair,replace,ormakeremunerationforthe
Product(eitherthesameorequivalentvalue)withoutcharge.
How to Obtain Warranty Service: InordertoenforceyourrightsunderthisLimitedWarranty,youmustfollowtheseprocedures:
YoumustreturntheORIGINALCOPYOFYOURSALESRECEIPTtotheCompany.
YoumustcalltheCompany'sConsumerServiceDepartmentat1-973-585-4747ortoll freeat1-877-279-7071onMondaythroughFridaybetweenthehoursof9:00
A.M.and5:00P.M(EST)to notifytheCompanyofthenatureoftheproblem.AttheCompany'soption,replacementpartsoranewProduct(eitherthesameor
equivalentvalue)will besenttoyouatnocharge.
Ifyouareinstructedtoreturnthe ProducttotheCompanyforservicing,youareresponsibleforshippingtheProduct,atyourexpense,totheaddressdesignated
bytheCompanyin packagingthatwill protectagainstfurtherdamage.
Youmustalsoincludeyourname,address,daytimetelephonenumber,Productmodelnumber,andadescriptionofthe problem.
TheCompanywii[payforanyshippingchargestoreturntherepairedofreplacedProducttoyou.
THISLiMiTEDWARRANTYISAVAILABLEONLYTOTHEORIGINALPURCHASEROFTHEPRODUCTANDISVALIDONLYINTHEUNITEDSTATES.THECOMPANY'S
LIABILITYISLIMITEDTOTHEREPAIR,REPLACEMENT,ORREMUNERATION,ATITSOPTION,OFANYDEFECTIVEPRODUCTANDSHALLNOTINCLUDEANYLIABILITY
FORINDIRECT,INCIDENTAL,ORCONSEQUENTIALDAMAGESOFANYKIND.THISWARRANTYISEXPRESSLYMADEIN LIEUOFALLOTHERWARRANTIES,EXPRESSED
ORIMPLIED,INCLUDINGBUTNOTLIMITEDTOTHEIMPLIEDWARRANTYOFMERCHANTABILITYANDTHEIMPLIEDWARRANTYOFFITNESSFORAPARTICULAR
PURPOSE.SOMESTATESDONOTALLOWLIMITATIONSONHOWLONGANIMPLIEDWARRANTYLASTSORDONOTALLOWFOREXCLUSIONOFINCIDENTALOR
CONSEQUENTIALDAMAGES.TOTHATEXTENT,THEABOVELIMITATIONSMAYNOTAPPLYTOYOU.
ThisLimitedWarrantygivesyouspecificlegalrights,butyoumayalsohaveotherrightsthat varyfromstatetostate.
IfyouhaveanyquestionsregardingthisLimitedWarrantyortheoperationofthe Product,youmaycallorwriteus.
ALLWARRANTYCLAIMSMUSTBEACCOMPANIEDBYA COPYOFTHESALESRECEIPT/PROOFOFPURCHASE.REPORTANYDEFECTSTO:
EASTPOINT
S P 0 l{ T S
628 ROUTE 1O,SUITE #5 WHIPPANY, NEW JERSEY 07981 1-973-585-4747
[ [? ?
14
,!
Table Top -
It is OK to gently vacuum the felt side of the billiard table with any standard handheld vacuum brush
attachment.
If Hockey or Table Tennis side needs to be cleaned, you can use any gentle surface cleaner (no bleach or
ammonia) with a lint free cloth.
NOTE: DO NOT spray the cleaning product directly on the table surface. It must be applied to the cloth
directly. Then the table top can be wiped in a lengthwise direction
Pucks -
If a puck isrough or not gliding smoothly on top of the table surface, gently sand off the scuff marks with
fine grit sandpaper.
Speed -
If faster puck speed isdesired, it isOK to use a wax or oil based cleaner to"slicken"the surface.
NOTE: DO NOT OVER APPLY. A little goes a long way.
NOTE: DO NOT spray the cleaning product directly on the table surface. It must be applied to
the cloth directly and then the table top can be wiped in a lengthwise direction.
EASTPOINT
S P O R T S
www.eastpoi ntsports.com
628 ROUTE 10, SUITE #5 WHIPPANY, NEW JERSEY07981 1-973-585-4747
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

EastPoint Sports 1-1-37001 Installation guide

Type
Installation guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI